• Structural Engineering and Mechanics
• /
• v.60 no.1
• /
• pp.1-19
• /
• 2016

In this study, the supersonic panel flutter of doubly curved composite sandwich panels with variable thickness is considered under aerothermoelastic loading. Considering different radii of curvatures of the face sheets in this paper, the thickness of the core is a function of plane coordinates (x,y), which is unique. For the first time in the current model, the continuity conditions of the transverse shear stress, transverse normal stress and transverse normal stress gradient at the layer interfaces, as well as the conditions of zero transverse shear stresses on the upper and lower surfaces of the sandwich panel are satisfied. The formulation is based on an enhanced higher order sandwich panel theory and the vertical displacement component of the face sheets is assumed as a quadratic one, while a cubic pattern is used for the in-plane displacement components of the face sheets and the all displacement components of the core. The formulation is based on the von $K{\acute{a}}rm{\acute{a}}n$ nonlinear approximation, the one-dimensional Fourier equation of the heat conduction along the thickness direction, and the first-order piston theory. The equations of motion and boundary conditions are derived using the Hamilton principle and the results are validated by the latest results published in the literature.

• Bulletin of the Korean Chemical Society
• /
• v.23 no.5
• /
• pp.741-744
• /
• 2002

Single phase of multicomponent oxide ZrTiO4 film could be prepared through surface sol-gel route simply by coating the mixture of 100 mM zirconium butoxide and titanium butoxide on $Pt/Ti/SiO_2Si(100)$ substrate, following pyro lysis at $450^{\circ}C$, and annealing it at 770 $^{\circ}C.$ The dielectric constant of the film was reduced as the film thickness decreased due to of the interfacial effects caused by layer/electrode and a few voids inside the multilayer. However, the dielectric property was independent of applied dc bias sweeps voltage (-2 to +2 V).The dielectric constant of bulk film, 31.9, estimated using series-connected capacitor model was independent of film thickness and frequency in the measurement range, but theoretical interfacial thickness, ti, was dependent on the frequency. It reached a saturated ti value, $6.9{\AA}$, at high frequency by extraction of some capacitance component formed at low frequency range. The dielectric constant of bulk ZrTiO4 pellet-shaped material was 33.7 and very stable with frequency promising as good applicable devices.

• Journal of ILASS-Korea
• /
• v.2 no.4
• /
• pp.29-35
• /
• 1997

Liquid film thickness is measured by $moir\acute{e}$ topography which monitored liquid surface. $Moir\acute{e}$ fringe measurement techniques share the inherent simplicity found in optical interferometric techniques have the advantage of use over a greater range of displacement. $Moir\acute{e}$ fringe are the geometric interference patterns observed when two dense line grating are superposed. Light transmitted through a fixed line grating is deviated by the liquid film surface, producing a distored image of the grating. The $moir\acute{e}$ fringe produced by projection of this optically distored grating onto a second stationary grating permit visualization of the liquid surface and measurement of the liquid film thickness. This study measured the small amplitude of liquid film thickness to the $moir\acute{e}$ fringe pattern produced when spherical metal was dropped glycerin put)1 And the measurement of liquid film thickness flowing down an inclined plate are required to calculate the liquid slope in a position.

• Journal of the Society of Naval Architects of Korea
• /
• v.45 no.5
• /
• pp.562-568
• /
• 2008

In this study, the target FSICR class is 1A whose target thickness of the brash ice is 46 mm in model scale. Normally ice floes for brash ice do not exceed 2 m in full scale, so the model ice sheet was cut by about 10 cm by 10 cm using hand saws. Since the target thickness of brash ice is 46 mm, 46 mm ice sheet makes one layer brash ice. For 23 mm thickness ice sheet, two layers should be accumulated to reach 46mm brash ice thickness. For 15mm thickness ice sheet, three layers need to be accumulated as the same as those in 23 mm ice sheet. New methodology to produce a brash ice was proposed. The results showed that it would be important to use multi-layer rather than single layer possibly because of significant thrust deduction from the propeller-ice interaction in the present ice condition (FSICR 1A).

• Solar Energy
• /
• v.17 no.1
• /
• pp.35-46
• /
• 1997

In this study comparison of experiment results with the computed results of linear theory and nonlinear theory using singularity method was obtainable. Specially singularity points like sources and vortexes on hydrofoil and freestreamline were distributed to analyze two dimensional flow field of supercavitating cascade using nonlinear theory, and governing equations of flow field were derived and hydraulic characteristics of cascade were calculated by numerical analysis of the governing equations. The results compared linear theory and nonlinear theory with the experiment results of the study are as follows: The tolerances of nonlinear theory were larger than those of linear theory in case of ${\alpha}<10^{\circ}$. Moreover the computational range of attack angles could be expanded from ${\alpha}=10^{\circ}$ to ${\alpha}=25^{\circ}$, the flow field of supercavitating cascade could be analyzed in the condition which the wake thickness and the length of cavity are a variable. The shapes of cavity were changed sensitively according to various variable such as attack angles, pitches and wake thickness, and the pressure distribution of hydrofoil surface was identical almost disregarding wake thickness but changed largely according to attack angle and the length of cavity. Lift coefficient and drag coefficient were reduced according to increasing of wake thickness but the influences of wake thickness were very little in the situation of small pitch and long cavity.

• Journal of Magnetics
• /
• v.14 no.4
• /
• pp.155-160
• /
• 2009

This study examined the effects of a decrease in thickness of magnetic alloy flakes on the electromagnetic wave absorption characteristics of nanocrystalline $Fe_{73.5}Cu_1Nb_3Si_{15.5}B_7$ (at.%) alloy flakes/polymer composite sheets available for a quasi-microwave band. The thickness of FeCuNbSiB alloy flakes decreased to 1-2 $\mu$m with increasing milling time up to 24 h, and the composite sheet including alloy flakes milled for 24 h exhibited considerably enhanced power loss properties in the GHz range compared to the sheets having non-milled alloy powders. Although a considerable increase in loss factor upon milling was observed in the narrow frequency range of 4-6 GHz, there was no correlation between the complex permeability and flake thickness. However, the complex permittivity increased with increasing milling time, and there was good agreement between the milling time and the frequency dependences of the complex permittivity and power loss.

• Proceedings of the Korean Nuclear Society Conference
• /
• 1995.10a
• /
• pp.450-455
• /
• 1995

A three-dimensional numerical tool is developed to calculate the potential distribution, electric field, and conductance for any types of conductance probes immersed in the wavy liquid film with various shapes of its free surface. The tool is validated against various analytical solutions. It is applied to find out the characteristics of the wire-wire probe, the flush-wire probe and the flush-flush probe in terms of resolution, linearity, and sensitivity. The wire-wire probe shows high resolution and excellent linearity for various film thickness, but comparably low sensitivity for low film thickness fixed. The flush-wire probe shows good linearity and high sensitivity for varying film thickness, but resolution degrading with an increase in film thickness. In order to check the applicability of the three types of probes in the real situation, the Korteweg-de Vries(KdV) two-dimensional solitary wave is simulated. The wire-wire probe is strongly affected by the installation direction of the two wires; when the wires are installed perpendicularly to the flow direction, the wire-wire probe shows large distortion of the solitary wave. In order to measure the transverse profile of waves, the wire-wire probes and the flush-wire probes are required to be separately installed 2mm and 2mm, respectively.

• Journal of the Korean Society for Heat Treatment
• /
• v.13 no.5
• /
• pp.355-359
• /
• 2000

Ion beam assisted deposition system was used to deposit CNx coatings with various thickness on the substrates of high-frequency induction hardened steels. Rolling contact fatigue tests were performed using Polymet RCF-1 machine with a constant supply of lubricant. Rolling contact fatigue life was substantially different in the steels with various thickness of CNx coatings. The optimum thickness of CNx coating was found to be $8.9{\mu}m$, showing the longest fatigue life, mainly caused by higher resistance to initiation of cracks and protective overcoat remaining to the surface failure during rolling contact fatigue. Cracks were initiated in the substrates under the surface of wear track and propagated to the surface, which eventually resulted in the failure. The reduction of fatigue life observed in the specimen with elimination of CNx coating during rolling contact fatigue was explained by the substrates deformation.

• Clinics in Shoulder and Elbow
• /
• v.6 no.2
• /
• pp.161-166
• /
• 2003

Purpose: To evaluate the usefulness of arthroscopic repair that was related with full thickness rotator cuff tear and assess clinical result. Materials and Methods: Twenty-one cases of arthroscopically repaired full thickness tear of rotator cuffs were studied. Between October 1998 to July 2002 we have analysed 21 repairs of FTRCT the average age 54(42∼74) years old, mean follow-up was 24(12∼41) months We analyzed the results statistically by paired t-test. Results: Postoperative VAS of pain improved average 7.2 to 1.9, UCLA score improved 13.9 to 31.9, ADL improved 11.5 to 25.5 respectively(all, p<0.001). Eighty-seventh ％ of the patients showed excellent St good results at the final follow-up. The satisfied rate was 90.5%(19cases). Conclusions: Arthroscopic repair in full thickness rotator cuff tear is effective surgical methods.

• Korean Journal of Poultry Science
• /
• v.25 no.3
• /
• pp.103-111
• /
• 1998

This study was carried out to estirnate the heritabilities and genetic correlations on egg shape index and internal egg qualities ; shell thickness, alburnin heights and Haugh units for breeding plan and selection in Korean native chicken. Data analyzed were the records of 46,908 eggs from 43() layers from April, 1994 to September, 1995. The egg shape index at the first egg, 300 days and 500 days of ages were 74.771, 74.468 and 73.702; the shell thickness were 0.345, 0.344 and 0. 334mm; the alburnen heights were 6.579, 6.130 and 5.318mm; the Haugh units were 86.859, 81.014 and 73.565 respectively. The heritability estimates of egg shape index and internal egg qualities based on the variance of sire, dam and combined components at 300 days of age were 0.136, 0.954 and 0.545 for egg shape index; 0.201, 0.622 and 0.421 for shell thickness; 0.410, 0.961 and 0.633 for albumen height ; 0.353, 0.962 and': 0.608 for Haugh units. The genetic correlation coefficient between shell thickness and albumen height was -0.044~0.824; 0.016~0.949 between Haugh units and shell thickness 0.313~0.941 between albumen height and Haugh units, respectively.