• The Journal of the Korean dental association
• /
• v.54 no.7
• /
• pp.542-550
• /
• 2016

Recent technological advance have greatly expanded the application of invisible orthodontic treatment using clear thermoplastic materials. However, the final outcomes using clear aligner system do not achieve the level of final goal frequently, which results in case refinement, midcourse correction, or fixed orthodontic treatment. Therefore, mechanical properties of thermoplastic materials should be considered to improve the quality of outcomes. The purposes of this special article were to evaluate the force and stress depending on the materials, deflection and thickness of thermoplastic materials and to evaluate the mechanical properties of thermoplastic materials after repeated loading. Thickness and amount of deflection rather than products and materials showed the largest effect on force and stress. In all products, at least 159 gf of force was required for more than 1.0 mm deflection or when materials with 1.0 mm thickness were deflected. Orthodontic forces delivered by thermoplastic materials depend on the materials, thickness, amount of activation, and intra-oral condition. Proper thickness of thermoplastic materials and deflection level of tooth movement should be decided for the efficient and physiologic tooth movement.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.36 no.7
• /
• pp.447-452
• /
• 1987

In this paper, the dependence of piezoelectric properties in the 0-3 composite system of piezoelectric-ceramics polymer materials on particle size of ceramics were investigated. Radial mode and thickness mode of composite were observed similar to single phase of piezoelectric ceramics. The measured values of dielectric constant and dissipation factor were dependent on particle size, which increased with the increasing particle size. the planar coupling factor, thickness coupling factor and thickness frequency constant with the particle size were almost constant, while planar frequency constant increased. The thickness coupling factor decreased with the increasing thickness of specimen. It is found that maximum voltage coeffidient was calculated on the specimen with particle size smallar than 46 ${\mu}m$.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.07b
• /
• pp.1007-1010
• /
• 2003

We made use of $Alq_3$ which is the representative light-emitting material. Electric conduction mechanism and luminance characteristics were analyzed in this paper. We have also measured current density-thickness-voltage characteristics with thickness variation from 60 to 400nm. we analyzed the low electric and the high electric field in theoretically. Also, maximum luminous efficiency is the thickness 200 nm of $Alq_3$ in luminous-thickness characteristics.

• Journal of The Korean Digital Architecture Interior Association
• /
• v.11 no.2
• /
• pp.31-39
• /
• 2011

Concrete-filled steel tube(CFT) columns have become popular for building construction due to not only composite effect of steel tube and infilled concrete, but also more economical. The purpose of this paper is to propose the applicable boundary formula of width-to-thickness ratio for rectangular steel tube as using CFT column. A parametric study was performed taking width-to-thickness ratio of rectangular steel tube and compressive strength of concrete as the main parameter. The strength of concrete are selected to 30, 60, 90MPa. The non-linear analysis was adopted in order to take into account the effect of concrete strength. Finally, from the test and analysis results, the effect of increasing strength according to concrete strength and width-to-thickness of steel tube and plastic behavior of specimens were verified distinctly.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2010.06a
• /
• pp.232-232
• /
• 2010

Simulation Program (AFORS-HET 2.4.1) was used, include the basic structure of crystalline silicon thin film as above, under the intrinsic a-Si:H films bonded symmetrical structure (Symmetrical structure) were used. The structure of ITO, a-Si p-type, intrinsic a-Si, c-Si, intrinsic a-Si, a-Si n-type, metal (Al) layer has one of the seven. When thickness for each layer was given the change, the changes of a-Si p-type layer and the intrinsic a-Si layer on top had an impact on efficiency. Efficiency ratio of p-type a-Si:H layer thickness was sensitive to, especially a-Si: H layer thickness is increased in a rapid decrease in Jsc and FF, and efficiency was also decreased.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.124-125
• /
• 2008

The charge trapping and tunnelling characteristics with various thickness of $Si_3N_4$ layer were investigated for application of TBE (Tunnel Barrier Engineered) non-volatile memory. We confirmed that the critical thickness of no charge trapping was existed with decreasing $Si_3N_4$ thickness. Also, the charge trap centroid x and charge trap density were extracted by using CCS (Constant Current Stress) method. Through the optimized thickness of $Si_3N_4$ layer, it can be improve the performance of non-volatile memory.

• Journal of Mechanical Science and Technology
• /
• v.15 no.7
• /
• pp.859-865
• /
• 2001

This paper reports on the theoretical analysis of mixed lubrication for the piston ring. The analytical model is presented by using the average flow and asperity contact model. The cyclic variations of the nominal minimum oil film thickness are obtained by numerical iterative method. The total friction is calculated by using the hydrodynamic and asperity contact theory. The effect of the roughness height, pattern, and engine speed on the nominal minimum film thickness, friction force, ad frictional power losses are investigated. As the roughness height increases, the nominal oil film thickness and total friction force increase. Also, the effect of the surface roughness on the boundary friction is dominant at low engine speed and high asperity height. The longitudinal roughness pattern shows lower mean oil film pressure and thinner oil film thickness compared to the case of the isotropic and transverse roughness patterns.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1997.04a
• /
• pp.567-571
• /
• 1997

Recently, automobile industry has led to increasing use of aluminum alloy for weight reduction. Automobile made of aluminum alloy can be given lighter, stronger and a harder surface by anodizing than one made of steel-alloy. In this paper, we investigate the influence of lap length, adherend thickness and adhesive thickness on adhesive strength of single-lap adhesive joints by conducting tensile-shear tests. Single-lap adhesive joints of aluminum was calculated using joint factor by using adhesive length, adherend thickness of specimen.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.06a
• /
• pp.686-689
• /
• 2003

Many technologies are applied to the measurement of elastohydrodynamic lubrication (EHL) film thickness. In particular, optical in-situ interferometric method has many advantages in making the actual contact behaviors realized with the experimental apparatus. Careful selection of incident lights greatly enhances the fringe resolution up to nanometer scale by using image processing technology. In this work, it is found that dichromatic incident light can provide much finer resolution of EHL film thickness than monochromatic incident light, because it has much more variables of color components to be discriminated among the wavelengths of colors according the variations of EHL film thickness. Some simulated interferometric images are shown how the film thickness is resolutionized in nanometer scale

• Journal of the Korean Society for Precision Engineering
• /
• v.6 no.2
• /
• pp.58-64
• /
• 1989

Plastic instability in uniaxial tension of commercial purity Al has been studied with the emphasis of effects of thickness in cold worked specimens and recrystallized specimens. The thickness change gave rise to change in stress state and the amount of strain localization in specimen after diffuse necking. Therefore the thickness of speci- men could control modes of plastic instability. Regardless of recrystallized or cold worked state, the necking mode changed from diffuse necking to local necking, at about 1.5 .approx. 2 mm in thickness.