• Proceedings of the KIEE Conference
• /
• 2006.07d
• /
• pp.1799-1800
• /
• 2006

ATPS(Automatic Transmission Position Sensor) is the position sensor of an automatic transmission which transforms the gear changes into the electrical signals and transmits them to TCU. This paper deals with an development of the sensor output signal analysis system for ATPS inspection using LabVIEW. The developed system is designed to carry easily, and it can be installed for inspection directly in a car fitted with an automatic transmission. The system can not only detect the output signals of the sensor but also inspect the sensor behavior under the running state of a car. For this, the system is designed to control the position and the speed of motor. Also, it has the database system for the systematic output data management and the convenient GUI for user.

• Proceedings of the IEEK Conference
• /
• 2002.07c
• /
• pp.1768-1771
• /
• 2002

Automatic Transmission System(ATS) was designed to replace the human's manual operation of the gear box. So far, this system operates with the fixed shift pattern information. In this paper, new algorithm considering driver's operation tendency is proposed. Also, to get rid of the uselessly frequent shift of the ATS, the conditions and the status of the vehicle would be included for the evaluation in making a decision of shifting. A field test is done in a car equipped with the computer set connected to Transmission Control Units(TCU) to check the status of the test car, and it shows the excellency of the proposed algorithm.

• Proceedings of the Earthquake Engineering Society of Korea Conference
• /
• 2003.09a
• /
• pp.82-89
• /
• 2003

Near-field ground motions exhibit special characteristics that are different from ordinary far-field ground motions. In this study the shaking table tests were conducted to evaluate the effect of earthquake ground motions with different characteristics on the response of the structure. The ground motions used in this study were the scenario earthquake, design earthquake, and Chi-Chi earthquake measured in TCU052 station. These earthquakes have different frequency contents. The test results show that the frequency content of ground motion is very important to the response of structures. The floor responses of structure were greatly affected by the higher modal frequencies, as well as the fundamental frequency. The responses of third floor were significantly reduced due to the interaction between the structure and the base isolated mass installed at the third floor.

• Journal of Drive and Control
• /
• v.10 no.4
• /
• pp.7-13
• /
• 2013

A tractor is a farm vehicle that is designed to provide a high tractive effort at low speed. It is used for versatile agricultural tasks such as hauling a trailer, tillage, mowing and construction work. As the intensity of work increases, tractors equipped with automatic transmission become popular due to the work convenience. Though manual and power shuttle transmissions are produced by domestic corporations, development for full-automatic power shift transmissions has never been challenged, and so related technology level is quite low. This paper gives a survey of the automatic transmissions from advanced foreign company, which includes layout of gear train, the way hydraulics controls clutches and brakes, electronic control system. The results are expected to be utilized as a basis in the development of original power train design for tractor.

• Journal of Korean Society of Environmental Engineers
• /
• v.35 no.6
• /
• pp.442-448
• /
• 2013

There are two approaches in measuring colors (or chromaticity) in water, i.e., visual comparison method and spectrophotometric method. The color of sample was determined by comparing with that of platinum-cobalt standard solution in the visual comparison method. Single or multiple wavelengths are used for the spectrophotometric method. As the accuracy and precision of visual comparison method depend on the eye sight of the analyzer, the results are not so reliable and representative. In addition, it is hard to measure chromaticity less than 5 TCU. Single wavelength approach in spectrophotometric method, can be applied for groundwater or surface water with natural organic matter (i.e., humic substances) while it's hard to measure the color of wastewater which includes anthropogenic chemical compounds. The measurements with multiple wavelengths approach resulted in reliable data regardless of the source of sample water, i.e., surface water and wastewater. As dozens of measurements and complicated calculations for one sample were required for the multiple wavelengths approach, the approach could not be applied for field measurement. In the present study, the authors tested efficient method which could measure the color of water sample accurately and precisely regardless of the source of water. With the colorimeter with multiple wavelengths and calculation program, the colors of water samples could be measured within 3~4 seconds with accuracy and precision.

• Journal of the Korean Society for Precision Engineering
• /
• v.27 no.5
• /
• pp.27-35
• /
• 2010

A loader used for uploading materials into truck is a kind of construction equipment. Mainly, a wheel loader is applied to construction work. Recently, an automatic transmission for the wheel loader is used to help drivers get the repetitive works done comfortably. It is composed of geartrain, clutch pack, hydraulic control system and TCU. Especially, a high-performance proportional control valve and its control algorithm is demanded to achieve the shift quality during a change of speed. In this paper, the commercial package program was used in order to justify model of the proportional control valve and simulate it. Steady-state and dynamic characteristics of PCV were analyzed to classify attractive forces and hydraulic control characteristics. This model also was verified the validity compared to the experimental result. Using the developed model, performances of PCV were predicted as studying design parameters.

• Journal of Drive and Control
• /
• v.17 no.3
• /
• pp.47-56
• /
• 2020

As a shift control of automatic transmission was managed with the electronic control unit (ECU), shift quality which is a measure of shift shock during gear change has markedly improved. However, the initial clutch pressure control of the clutch filling phase should continue to rely on the predetermined control input since the input and output speeds are unchanged until the shifting process attains the inertia phase. It is critical to minimize the clutch response time and control the clutch pressure accurately at the end of clutch fill to achieve quick shift response and smoothness. Advanced transmission companies have adopted an auto calibration method which establishes the databases for the clutch piston fill-up attributes and the frictional characteristics of the disks. In this study, a distinctive auto calibration algorithm for forklift transmission under development is proposed and verified with the real-vehicle test. The experimental calibration results showed consistent turbine dynamics at the initial stage of shifts with the properly calibrated clutch-fill control parameters. By using this technique, it is necessary to finalize the shift control for the various operation conditions.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.19 no.1
• /
• pp.132-141
• /
• 1995

The torque converter, an important component of automatic transmissions, is a hydrodynamic device which has a great influence on transient characteristics of vehicle during shift. To predict the accurate driving performance in extremely transient state such as shifting process, a detailed analysis of the torque converter is required. In this study, one dimensional performance model of the torque converter based on the concept of mean flow path, was used to analyze the shifting transients and the exact values of equivalent parameters were determined from the experimental results by using BOX program. The dynamic modelings of the components of power transmission systems such as engines, planetary gear systems, clutches and one-way clutches, were carried out. To analyze the shifting transients of tracked vehicle, a simulation program was developed. In the modeling of power transmission systems, the stiffness of shafts was neglected and shifting control logic(TCU) was included. Using the developed simulation program, the driving conditions were simulated and the results of simulation were verified through the experiments on the dynamometer.

• Proceedings of the KIEE Conference
• /
• 2007.07a
• /
• pp.1585-1586
• /
• 2007

In this paper, a system of durability test for ATPS(Automatic Transmission Position Switch), which is used for automatic transmission, has been developed. ATPS is the position sensor for an automatic transmission which transforms the gear changes into the electrical signals and transmits them to TCU(Transmission Control Unit). This system can detect the output signals of the sensor, and also it has been designed to control the position and velocity of a motor to realize the sensor's movement under the running state of a car. And a database system and a GUI system have been developed for the systematic output data management and the convenient interface for users. Also, the operation data and the inspection reference data of a motor can be easily changed in this system, and with some modification the system is also able to used for the durability test of the similar products.

• Journal of Drive and Control
• /
• v.11 no.3
• /
• pp.47-54
• /
• 2014

Clutches are an integral part of the automatic transmission for changing gears. Modern automatic transmissions make extensive use of wet multiple-disc clutches employing hydraulic actuation mechanism with electronic control. Although nowadays, highly advanced shifting algorithm implements the superior shift quality and transmission efficiency, its performance should be based on smooth, reliable engagement with a reasonably durable friction material as well as stable clutch piston dynamics. Particularly, clutch filling control is the crucial part of shifting process because only the open-loop control is available due to the lack of measurement. In this paper, the effect of clutch-fill control parameters on clutch piston dynamics is experimentally investigated by using clutch piston test equipment which enables the clutch piston to actuate similar to real shifting conditions. The experimental analysis results can be expected to be utilized for the calibration of proportional solenoid valve as reference current profile data in vehicle test.