• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.07b
• /
• pp.934-937
• /
• 2003

Glasses in the system $CuO-P_2O_5-V_2O_5$ were prepared by a press-quenching method on the copper plate. The glass-ceramics from these glasses were obtained by post-heat treatment, and the crystallization behavior and DC conductivities were determined. The conductivities of the glasses were range from $10^{-6}s.Cm^{-1}$ at room temperature, but the conductivities of the glass-ceramics were $10^{-3}s.Cm^{-1}$ increased by $10^3$ order. The crystalline product in the glass-ceramics was $CuV_2O_6$. Heat-treatment conditions influenced the crystal growth of $CuV_2O_6$ and conductivity. The linear relationship between in (${\sigma}T$) and $T^{-1}$ suggested that the electrical conduction in the present glass-ceramics would be due to a small polaron hopping(SPH) mechanism.

• Journal of the Korean Ceramic Society
• /
• v.30 no.1
• /
• pp.17-24
• /
• 1993

Sol-gel spin-coating technique was used to produce Nb2O5 thin films on silicon substrates from Nb(OC2H5)5 precursor. The films were heat-treated at temperatures between $600^{\circ}C$ and 100$0^{\circ}C$ in oxygen atmosphere and their crystalline phases, chemical states, and dielectric characteristics were investigated by X-ray diffractometry (XRD), Auger electron spectroscopy (AES), and C-V measurements, respectively. After 1 hour heat-treatment at 80$0^{\circ}C$, T-type Nb2O5 was formed, and its chemical composition was homogeneous with no appreciable SiO2 oxide at interfaces between the films and substrates. The films heat-treated at temperatures between $600^{\circ}C$ and 80$0^{\circ}C$ exhibit dielectric constant of less than 20 while the films heat treated at 100$0^{\circ}C$ show dielectric constant of 28.

• Proceedings of the KWS Conference
• /
• 2002.10a
• /
• pp.59-64
• /
• 2002

Effects of the aging treatments on the microstructure and strength of heat affected zone(HAZ) in the welds of a age-hardened Al-Mg-Si alloy, 5N01-T5, were investigated. The base metal aging treatments before MIG welding were conducted at 423K to 473K for 28.8ks Post weld heat treatment(PWHT) to recover the HAZ strength was performed at 448K for 28.8ks. Microstructure observations, hardness measurements and tensile tests were conducted to study properties of the MIG weld joints. The position of the softest region in HAZ where the hardness insufficiently recovered after natural aging and PWHT was at a distance of approximately 15mm from the center of the fusion zone. Hardness of the softest regions after natural aging and PWHT decreased with increase in the base metal aging temperature. TEM observation clarified that strengthening ${\beta}$"(Mg$_2$Si) precipitates and coarse ${\beta}$′ precipitates affected the hardnes of HAZ. Incomplete recover of hardness in HAZ after PWHT was caused by the precipitating of non-hardening ${\beta}$′ phase during the weld thermal cycle. In order to examine the effects of weldheat input and welding speed, the laser weld joints were also investigated and compared with the MIG weld ones. Laser welding had the narrower width of the softened regions in HAZ compared with MIG welding. The hardness of the softest regions of the laser welds after PWHT was higher than that of the MIG welds. Quantitative relations between hardness of the softest region and base metal aging temperature were obtained for both welding processes. Accordingly, the equations to estimate the strength of the weld joints after PWHT with varying base metal temperatures were proposed for MIG welding and laser welding.

• Journal of the Korean Society for Heat Treatment
• /
• v.31 no.2
• /
• pp.49-55
• /
• 2018

A T-shape structure was manufactured by the superplastic forming and diffusion bonding process using two Ti-3Al-2.5V alloy tubes. A Ti-3Al-2.5V tube was prepared for the hydroforming in the superplastic condition until it reaches a surface area such as a roof welded in the hole of another Ti-3Al-2.5V tube. Afterward, the superplastic forming process and the diffusion bonding process were carried out simultaneously until the appropriate bonding along the interface area of two Ti-3Al-2.5V tubes was obtained. The bonding qualities were different at each location of the entire interface according to the applied process conditions such as strain, pressure, temperature, holding time, geometries, etc. The microstructures of bonding interface have been observed to understand the characteristics of the applied processes in this study.

• Journal of Korea Foundry Society
• /
• v.13 no.3
• /
• pp.259-267
• /
• 1993

The effects of casting processes-direct and indirect squeeze casting, permanent mold casting and die casting on the microstructure and mechanical properties were studied for the hypereutectic B390 aluminium alloy. The effects of T5 and T6 heat treatment were also examined. The direct and indirect squeeze casting showed no casting defects such as porosity and shrinkage were observed in permanent mold castings and die castings. The primary silicon phase was refined and homogeneously distributed in the order of indirect squeeze casting, diecasting, direct squeeze casting and permanent mold casting. Depletion of primary silicon phase in die casting surface was disappeared in indirect squeeze casting. Tensile strength of cast and heat treated specimens were increased in the order of direct squeeze casting, permanent mold casting, indirect squeeze casting and die casting. Hardness of indirect squeeze castings was larger than that of other castings. As indirect squeeze casting of B390 aluminium alloy, the time of T6 heat treatment to achieve high strength can be reduced.

• Journal of Korea Foundry Society
• /
• v.36 no.6
• /
• pp.181-186
• /
• 2016

The typical microstructure of Al-5%Mg-2%Zn cast alloy mainly consists of an aluminum matrix with a small amount of AlMgZn 2nd phase. The secondary dendrite arm spacing and the grain size of the cast alloy tend to be inversely proportional to the section thickness of casting; however, the tensile properties cannot be said to be clearly related to the cast microstructure. After T6 heat treatment, the tensile strength of the alloy was enhanced significantly. TEM analysis results show that very fine AlMgZn precipitates were formed after the heat treatment. The corrosion resistance, measured according to the corrosion potential, was found to increase slightly after the conducting of heat treatment.

• Journal of the Korean Ceramic Society
• /
• v.32 no.3
• /
• pp.385-393
• /
• 1995

Akali-resistant porous glass was prepared by phase separation in Na2O-B2O3-SiO2 system containing ZrO2 and MgO. ZrO2 was added for alkali-resistance and MgO for anti-cracking during leaching. Optimal content of ZrO2 for alkali-resistance was 7wt% and devitrification by heat treatment resulted from further addition. Pore size and pore volume were decreased and specific surface area was increased with ZrO2 addition due to depression in phase separation. Addition of 3mol% MgO to mother glass containing 7wt% ZrO2 was effective for anti-crack during leaching. In this case, with phase separation at 55$0^{\circ}C$ and 5$25^{\circ}C$ for 20 hrs. crack-free porous glasses could be prepared. The relation between pore size r and heat treatment time t at 55$0^{\circ}C$ was D=25.58＋18.16t. According to measurement of gas permeability, the mechanism of gas permeation was Knudsen flow. N2 and He permeability of porous glass which was prepared by heat treatment at 55$0^{\circ}C$ for 20 hrs. were 0.843$\times$10-7mol/$m^2$.s.Pa and 2.161$\times$10-7mol/$m^2$.s.Pa respectively.

• Journal of the Korean Society for Heat Treatment
• /
• v.4 no.4
• /
• pp.34-43
• /
• 1991

A small amount of misch metal and/or Zr was added as a dopant to 70.5wt----Cu-26wt----Zn-3.5wt----Al shape memory alloy in order to study the effect of grain refinement and heat treatments on the transformation behavior, stabilization of martensite, and shape memory ability. It was found that the addition of misch metal and Zr was very effective for reducing the grain size. The fracture mode has been changed from intergranular brittle fracture to ductile fracture with void formation and coalescence by the addition of misch metal and Zr. Aging of the ${\beta}$-phase decreases the $M_s$ temperature, but that of the martensite phase increases the $A_s$ temperature. The hysteresis of transformation temperature ${\Delta}T(A_s-M_s)$ has an increasing tendancy by grain refinement. The crystal structure of martensite was identified as monoclinic structure. As the grain size decreased, martensite stabilization more easily occured and the shape, memory ability has been reduced by the grain size refined.

• Progress in Superconductivity
• /
• v.8 no.1
• /
• pp.54-58
• /
• 2006

We have fabricated double stacked 385 filamentary Bi2212/Ag round wires which have different Ag ratios. The wires have been heat-treated at the maximum temperature($T_{max}$) of $882{\sim}896^{\circ}C$ for 0.5 h. Effect of heat treatment on critical current density and critical temperature on Bi2212/Ag round wires has been studied. Critical current density of the wire heat -treated at $890^{\circ}C$ showed 206,250 $A/cm^2$ at 4.2 K, 0 T and critical temperature of the wire was 83 K. Microstructure of the wires also has been studied via optical microscopy and SEM.

• Journal of the Korean Society for Heat Treatment
• /
• v.5 no.1
• /
• pp.32-40
• /
• 1992

This content is a part of the results of the study on the development of the vacuum carburizing technology. In this study the vacuum carburizing furnace being used was the furnace that developed through the joint project between KIMM and Kyung-Pook Heat Treating Co. from June 1988 to Nov. 1990. And the used carburizing gas was the propane gas and the introducing methods of the gas applied two methods such as pulse and constant pressure. By this study we established the basis of the furnace manufacturing technology and of the processing technology in the vacuum carburizing. Above all in this work there are notable meanings in a viewpoint of the foremost research in home. Hereafter, we are going to industrialize the vacuum carburizing technology by improving the results of the present work and by developing the process for the mass production.