• Journal of Fashion Business
• /
• v.15 no.1
• /
• pp.63-79
• /
• 2011

This study examines the relationship between breast shape and brassiere construction through the comparative analysis of brassiere pattern on the breast shape. This researcher drew the brassiere pattern of developing a pre-study for Chinese female adults according to average size based on the four breast shapes. And then we measures brassiere pattern size and comparatively analyzes breast between size and shape. Comparative analysis results of brassiere patterns are verified differences of size and shape on the breast shape. Above all an angle of cup dart showed remarkable differences on the breast shape. An angle of cup dart isn't proportioned to breast size. An angle of cup dart for cone shape is bigger than dome shape. Because cone shape breast is protruded center part but dome shape breast have a shape of smooth curve like a half globe. So an angle of a cone shape breast cup dart is determined bigger than dome shape breast. For increasing the uplift effect of brassiere, brassiere pattern is different on the breast shape. And a brassiere pattern need different drawing methods about the angle of cup dart, breast inner side diameter, slope and so on. This study has an important significance that it established a mechanical relationship of breast shape and brassiere pattern.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.50 no.9
• /
• pp.456-465
• /
• 2001

In this paper, breakdown voltages in $SF_6-N_2$ mixtures were experimentally investigated to understand characteristics of dielectric strength and physical phenomena in nonuniform field disturbed by a needle shape protrusion. The test voltages are the lightning impulse$(\pm1.2/44 \mus)$ and the damped oscillatory impulse$(\pm400 ns / 0.83 MHz)$ voltages which can be occurred by the operation of disconnecting switches in gas-insulated switchgears(GIS). The effects of the polarity and wave shape of the test voltages, and the gas pressure on the V-t characteristics were in detail examined. The V-t characteristic curves were measured in different two ways : (1) one is the method by taking the maximum voltage recorded at or prior to breakdown against the time to breakdown, that is, the Procedures recommended in IEC 60060-1, (2) the other is the method by taking the voltage at the instant of chopping against the time to breakdown. As a result, the V-t characteristics of $SF_6-N_2$ mixtures in nonuniform electric field were significantly affected by the polarity and wave shape of the applied voltages. The positive breakdown voltages resulted in lower breakdown voltages in the time ranges considered, and the V-t curves for the negative oscillatory impulse voltage were extended over the longer time range. For the lightning impulse voltages, the V-t curves obtained by IEC Pub. 60060-1 were nearly same with the V-t curves obtained by the voltage at the instant of chopping against the time to breakdown. It is clear that the actual breakdown voltages were much lower than the maximum voltages appearing at or prior to breakdown because of the displacement current produced as a result of the dV/dt during the oscillatory transient voltage app1ication. The scattering of the negative actual breakdown voltages was much larger than that of the positive.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2017.05a
• /
• pp.58-59
• /
• 2017

Through the case study, we surveyed the performance of a CNC-T BAR system on irregular-shaped building construction project. By CNC T-BAR system, we mean a surface curvature control system has been used in aircraft and ship manufacturing by controlling entire surface points on shape. For the past 10 year, the number of irregularly-shaped building design and construction project has been increased, and also the studies on irregular-shaped construction methods have been conducted. However, the previous studies did not review on the performance of the CNC T-BAR system. We collected construction-completed cases in Korea, which applied the CNC T-BAR system, and we studied its performance by comparing with a segment system in terms of construction duration and its quality. The result shows that the CNC T-BAR system can shorten the construction duration comparing with segment-assembly system while maintaining high quality. The CNC T-BAR system is expected to apply on the more number of irregularly-shape building construction project.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.25 no.2
• /
• pp.250-256
• /
• 2017

Automatic transmission(A/T) is one of a car's core components. The durability of A/T has an effect on the durability of the car. The input shaft of A/T passes the power directly from the engine, so the durability of the input shaft for A/T is likewise vital. In this study, the test method of the input shaft is considered and the load spectrum of A/T is analyzed to secure durability of the input shaft. The shape parameter, T-N curve of the input shaft torsional fatigue test are obtained for life evaluation and analysis. Results of this study can be used to get the basic background of the durability test for A/T components.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.32 no.3
• /
• pp.443-453
• /
• 2008

The purpose of this study was to identify the perception between real and ideal body shapes of college students and to investigate the preferred body shape of college students. The research subjects numbered one hundred forty five male and female students, aged 20 to 29, who lived in Gwangju and Chonnam province. The anthropometric data was collected including both direct and indirect measurements. The data was analyzed by mean and standard deviation, t-test, and factor analysis. The results of t-test showed the significant difference($p{\leq}.001$) between real body size and ideal body size. The result showed that male students want to have bigger chest circumference and a taller height than their real body, the research also showed that the female students want to have a narrow bust and hip width along with a taller height than real body. Regarding ideal body shape, male students pursued bigger height and want an inverted-triangle body shape. On the other hand, female students pursued bigger height and slim body shape. This study established the factors(dimension of torso, height, the side shape of torso, and shoulder shape) as the perception between real and ideal body shapes. In terms of real body, the factor analysis shows two contrasting results in which the height is the most important factor for female students, while the torso dimension is the most important factor for male students. In terms of ideal body, the height factor is the most important for both the male and female students.

• Korean Journal of Computational Design and Engineering
• /
• v.9 no.4
• /
• pp.306-314
• /
• 2004

This paper explains the qualitative shape representation scheme and general shape analysis procedure based on shape feature categories. It takes two different groups of architectural drawings as examples and comparer them so as to confirm that the procedure is capable of comparing one group with another. In order to verify the validity of qualitative shape representation scheme, we used statistical methods as well as symbolic representation and analysis techniques. This paper concludes that two different groups of architectural drawings of similar kind are analyzed to be distinguished and specifically characterized. 11 drawings of Kahn and 13 drawings of Aalto are taken into considerations. Linear regressions are used in characterizing the shape featural relationships.

• Transactions of Materials Processing
• /
• v.18 no.7
• /
• pp.550-555
• /
• 2009

In the multi-pass shape drawing process, the pass schedule that includes the determination of reduction ratio and intermediate die shape is very important. This study used the equal reduction, equal load, and electric field analysis method for pass schedule of the multi-pass shape drawing. The reduction ratio was calculated by the equal reduction and equal load method. And the intermediate die shape was determined by the result of the electric field analysis and the calculated reduction ratio. The proposed pass schedule method was applied to a shape drawing for producing cross roller guide. Finally, FE-analysis and shape drawing experiment were performed to verify the effectiveness of the proposed method.

• Journal of Biosystems Engineering
• /
• v.26 no.3
• /
• pp.279-286
• /
• 2001

The purpose of this study were to organize a sorting system, to develop an algorithm of image processing for the shape sorting, and to finally develop a scientific and objective shape sorting system of Korean Red-Ginseng for mechanization of the shape sorting. The results of this study are followed. 1. The shape sorting system of Korean Red-Ginseng consists of a control computer, a color CCD camera(WV-CP4110) for image processing, an image processing board(DT3153), and an image acquisition unit. 2. Many image processing skill, such as sliding, stretching, threshold, binary and D$\sub$t/ were used to analyze the shape sorting factors of Korean Red-ginseng. 3. The sorting accuracy of the shape sorting system for the Korean Red-Ginseng was 74.7%. It is 21.1% lower than that of human inspector. Although the system has low accuracy, using more cameras may improve its sorting accuracy.

• 한국전산유체공학회:학술대회논문집
• /
• 2007.10a
• /
• pp.88-91
• /
• 2007

In the shape design optimization of an airfoil, the shape function has been used to find the optimal airfoil shape for given conditions. The parameters determining the airfoil shape are used in the shape design optimization as design variables. However, they usually don't have physical meaning. The PARSEC (Parametric Shapes) function is a recently proposed shape function and its parameters have the physical meaning. In this study the usefulness of the PARSEC is tested for the RAE2822 airfoil in the transonic flow region to reduce the shock strength and the result is compared with Hicks-Henne function. The optimized airfoils reduce the shock strength and they show similar result.

• Transactions of Materials Processing
• /
• v.18 no.4
• /
• pp.323-328
• /
• 2009

The prediction of drawing load is very important in the drawing process. However, it is not easy to calculate the drawing load for the shape drawing process through a theoretical model because of a complex arbitrary final cross section shape. The purpose of this study is to predict drawing load in shape drawing process. The cross section of product is divided with small angle as much as similar with fan-shape. The drawing load of each section was calculated by theoretical model of round to round drawing process. And the shape drawing load was determined by summation of drawing load of each section. The effectiveness of the proposed method was verified through the FE analysis and shape drawing experiment. It had a good agreement between proposed method, FE analysis and experiment within about 3% errors.