• Steel and Composite Structures
• /
• v.52 no.2
• /
• pp.121-134
• /
• 2024

To investigate the compressive behavior of partially encased recycled aggregate concrete (PERAC) stub columns after exposed to elevated temperatures, 22 specimens were tested. The maximum temperature suffered, the replacement ratio of recycled coarse aggregate (RCA), the endurance time and the spacing between links were considered as the main parameters. It was found that the failure mode of post-heated PERAC columns generally matched that of traditional partially encased composite (PEC) columns, but the flange of specimens appeared premature buckling after undergoing the temperature of 400℃ and above. Additionally, the ultimate strength and ductility of the specimens deteriorated with the elevated temperatures and extended heating time. When 400℃< T ≤ 600℃, the strength reduction range is the largest, about 11% ~ 17%. The higher the replacement ratio of RCA, the lower the ultimate strength of specimens. At the temperature of 600℃, the ultimate strength of specimens with the RCA replacement ratio of 50% and 100% is 0.94 and 0.91 times than that of specimens without RCA, respectively. But the specimen with 50% replacement ratio of RCA showed the best ductility performance. And the bearing capacity and ductility of PERAC stub columns were changed for the better due to the application of links. When the RCA replacement ratio is 100%, the ultimate strength of specimens with the link spacing of 100 mm and 50 mm increased 14% and 25% than that of the specimen without links, respectively. Based on the results above, a formula for calculating the ultimate strength of PERAC stub columns after exposure to high temperatures was proposed.

• Journal of the Korean Society of Industry Convergence
• /
• v.27 no.5
• /
• pp.1189-1197
• /
• 2024

Due to the rapid development of the industry, the use of iron is increasing rapidly in various industrial fields. Among these iron use areas, problems caused by corrosion of iron are seriously occurring in water-related industries. In particular, as the importance of environmental management has emerged, the water industry market desperately needs to replace aging water infra structure due to corrosion. In order to overcome this problem, research on a method capable of corrosion prevention system is being actively conducted. As the method for corrosion prevention system has various voltages and currents applied depending on the surrounding environment, the demand for an appropriate voltage regulator is increasing rapidly. In particular, as the IOT industry develops, the capacity of corrosion prevention system is increasing by expanding the area in which the method machine operates. Therefore, rectifiers for preventing corrosion are being changed from conventional flyback systems suitable for small capacities to inverter-type rectifiers suitable for large capacities. The inverter-type rectifier has various problems by reducing it to the initial rush current when starting. Therefore, this paper proposes a new starting method that can reduce initial inrush current in inverter-type rectifiers. T he proposed method can secure DC phase voltage for stable operation of the inverter by implementing discontinuous boosting operation using the switch of the inverter. In addition, the excellence of the proposed method was verified through simulations and experiments.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.20 no.6
• /
• pp.1163-1170
• /
• 2016

A hardware implementation of ultra-lightweight block cipher algorithm PRESENT which was specified as a standard for lightweight cryptography ISO/IEC 29192-2 is described. The PRESENT crypto-processor supports two key lengths of 80 and 128 bits, as well as four modes of operation including ECB, CBC, OFB, and CTR. The PRESENT crypto-processor has on-the-fly key scheduler with master key register, and it can process consecutive blocks of plaintext/ciphertext without reloading master key. In order to achieve a lightweight implementation, the key scheduler was optimized to share circuits for key lengths of 80 bits and 128 bits. The round block was designed with a data-path of 64 bits, so that one round transformation for encryption/decryption is processed in a clock cycle. The PRESENT crypto-processor was verified using Virtex5 FPGA device. The crypto-processor that was synthesized using a $0.18{\mu}m$ CMOS cell library has 8,100 gate equivalents(GE), and the estimated throughput is about 908 Mbps with a maximum operating clock frequency of 454 MHz.

• Journal of the Korean Applied Science and Technology
• /
• v.32 no.2
• /
• pp.330-338
• /
• 2015

The influences of fluorescence, scattering, and flocculation in turbid material by light scattering of N-propyl-N,N-dimethylethanolamine, fluorescence agent and absorption agent were interpreted for the scattered fluorescence intensity and wavelength. They have been studied the molecular properties by the spectroscopy of laser induced fluorescence (LIF) and flocculation. The effects of optical properties in scattering media have been found by the optical parameters(${\mu}_s$, ${\mu}_a$, ${\mu}_t$). Flocculation is an important step in many solid-liquid separation processes and is widely used. When two particles approach each other, interactions of several colloid particles can come into play which may have major effect on the flocculation and LIF process. The values of scattering coefficient ${\mu}_s$ are large by means of the increasing scattering of scatterer, The values have been found that the slope decays exponentially as a function of concentration from laser source to detector by our experimental result. It may also aid in designing the best model for oil chemistry, bio-pharmaceutical, laser medicine and application of medical engineering on LIF and coagulation in particle transport mode.

• Applied Chemistry for Engineering
• /
• v.10 no.7
• /
• pp.1014-1019
• /
• 1999

Copolyamic acid PMDA/6FDA-PDA(PAA) and homopolyamic acids PMDA-PDA(PAA) and 6FDA-PDA(PAA) were synthesized from 1,2,4,5-benzenetetracarboxylic dianhydride(PMDA) and 2,2'-bis(3,4-dicarboxyphenyl) hexafluoropropane dianhydride(6FDA) as the dianhydride and 1,4-phenylenediamine (PDA) as the diamine. Residual stresses were detected in-situ during thermal imidization of the co- and homopolyimide precursors as a function of processing temperature over the range of $25{\sim}400^{\circ}C$ using thin film stress analyzer(TFSA), and morphological structures were investigated by WAXD. In comparison, the resultant residual stress of polyimide films composed of different compositions decreased with the increasing content of PMDA unit in the chain and was about 5 Mpa in compression mode for PMDA-PDA. In this study, the synthesis of random PMDA/6FDA-PDA copolyimide could be completed and compensate for the difficulty of process due to high $T_g$ of PMDA-PDA and relatively higher stress of 6FDA-PDA. It showed that we can make a low level stress copolyimied having excellent mechanical properties by incorporating appropriate rod-like rigid structure PMDA-PDA unit into 6FDA-PDA polyimide backbone which generally shows higher stress due to rotational hinges such as bulky di(trifluoromethyl). Specially, PMDA/6FDA-PDA(0.9:0.1:1.0) satisfied excellent mechanical property and low level stress as an inter layer showing low dielectric constant.

• The korean journal of orthodontics
• /
• v.40 no.4
• /
• pp.267-275
• /
• 2010

Objective: The aim of this study was to evaluate and compare the shear bond strength (SBS) and failure-mode of orthodontic buttons bonded to erupted and unerupted teeth with conventional and self-etching adhesive systems. Methods: Eighty-four erupted and 84 unerupted, human third-molar teeth were used. For both groups, the buccal surfaces of each tooth were assigned one of the following type of adhesive systems (n = 12). A, Conventional systems: 1, Transbond XT (3M Unitek, Monrovia, CA, USA); 2, Prime & Bond NT (Dentsply/Caulk, Milford, USA); 3, Single Bond (3M ESPE, Minnesota, USA); and B, Self-etching adhesives; 4, Clearfil SE Bond (Kuraray, Okayama, Japan); 5, Transbond Plus (3M Unitek, Monrovia, CA, USA); 6, Clearfil S3 (Kuraray, Tokyo, Japan); 7, G Bond (GC, Tokyo, Japan). The SBSs of the attachments and the adhesive remnant index (ARI) scores were recorded. Data were analyzed with analysis of variance (ANOVA), independent-sample t-test and chi-square tests. Results: When the SBSs of erupted and unerupted teeth were compared, only the Clearfil-SE Bond and G-Bond were significantly different. Bond strengths of all adhesive systems were higher in unerupted teeth than erupted teeth, except the Single-Bond system. Conclusions: When using conventional adhesives, bonding to erupted and unerupted teeth may not be significantly different. However, clinicians need to take into consideration the types of self-etching systems before usage.

• Progress in Medical Physics
• /
• v.11 no.1
• /
• pp.73-83
• /
• 2000

In this study, we investigate the effects of poor shimming on quantitative measurement of ratios of metabolite levels by proton magnetic resonance spectroscopy ($^1$H MRS). Coefficient of variation (COV) of metabolite ratios for point resolved spectroscopy (PRESS) and stimulated-echo acquisition mode (STEAM) spectra was evaluated from a phantom containing in vivo levels of metabolites using a conventional whole body 1.5T MR system and conventional acquisition and analysis protocol. A statistical P-value was also calculated from a linear regression for relationship of metabolite ratios. N-acetylaspartate (NAA)/ creatine (Cr) and NAA/ choline (Cho) had low COV values for the long and short TE spectra (29.1 and 27.5%; 23.8 and 12.6 %), whereas Cho/Cr and Cr/Cho had high COV values (50.0 and 68.6 %; 27.5 and 29.3 %). A linear relationship between NAA/Cr and Cho/Cr, and between NAA/Cho and Cr/Cho revealed the statistical significance in the long and short TE spectra, respectively (P < 0.0001 and P < 0.0001; P = 0.015 and P = 0.005). There was no significant relationship between Cho/NAA and Cr/NAA in the measurement (P = 0.159; P = 0.910). The present study suggested that NAA/Cr and NAA/Cho could be useful for data with poor shimming in $^1$H MR spectroscopy. In conclusion, statistical significance of metabolite ratios indicated that the Cr and Cho levels could be interpreted as a significant alteration factor in the long and short TE spectra, and then should be used with care to provide precise metabolite quantification.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.10 no.5
• /
• pp.462-468
• /
• 2017

In this paper IoT/WSN(Internet of Things/Wireless Sensor Network) has been modeled with a random geometric graph. And a performance of the decentralized code for the efficient storage of data which is generated from WSN has been analyzed. WSN with n=100 or 200 has been modeled as a random geometric graph and has been simulated for their performance analysis. When the number of the total nodes of WSN is n=100 or 200, the successful decoding probability as decoding ratio ${\eta}$ depends more on the number of source nodes k rather than the number of nodes n. Especially, from the simulation results we can see that the successful decoding rate depends greatly on k value than n value and the successful decoding rate was above 70% when $${\eta}{\leq_-}2.0$$. We showed that the number of operations of BP(belief propagation) decoding scheme increased exponentially with k value from the simulation of the number of operations as a ${\eta}$. This is probably because the length of the LT code becomes longer as the number of source nodes increases and thus the decoding computation amount increases greatly.

• The Korean Journal of Financial Management
• /
• v.20 no.1
• /
• pp.191-212
• /
• 2003

Recently, there is a growing body of literature that suggests that information inefficiency is one of the causes of the asymmetric volatility. If this explanation for the asymmetric volatility is appropriate, then innovations, such as the introduction of futures, may be expected to impact the asymmetric volatility of stock market. As transaction costs and margin requirements in the futures market are lower than those in the spot market, new information is transmitted to futures prices more quickly and affects spot prices through arbitrage trading with spots. Also, the merit of the futures market may attract noise traders away from the spot market to the futures market. This study examines the impact of futures on the asymmetry of stock market volatility. If the asymmetric volatility is significant lower post-futures and exist in the futures market, it has validity that the asymmetric volatility is caused by information inefficiency in the spot market. The data examined are daily logarithmic returns on KOSPI 200 stock price index from January 4, 1993 to December 26, 2000. To examine the existence of the asymmetric volatility in the futures market, logarithmic returns on KOSPI 200 futures are used from May 4, 1996 to December 26, 2000. We used a conditional mode of TGARCH(threshold GARCH) of Glosten, Jagannathan and Runkel(1993). Pre-futures the spot market exhibits significant asymmetric responses of volatility to news and post-futures asymmetries are significantly lower, irrespective of bear market and bull market. The results suggest that the introduction of stock index futures has an effect on the asymmetric volatility of the spot market and are inconsistent with leverage being the sole explanation of asymmetry. However, it is found that the volatility of futures is not so asymmetric as expected.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.46 no.12
• /
• pp.105-112
• /
• 2009

In this paper, we investigated abnormal ESD failure on guard-rings in the smart power IC fabricated with $0.35{\mu}m$ Bipolar-CMOS-DMOS (BCD) technology. Initially, ESD failure occurred below 200 V in the Machine Model (MM) test due to current crowding in the parasitic diode associated with the guard-rings which are generally adopted to prevent latch-up in high voltage devices. Optical Beam Induced Resistance Charge (OBIRCH) and Scanning Electronic Microscope (SEM) were used to find the failure spot and 3-D TCAD was used to verify cause of failure. According to the simulation results, excessive current flows at the comer of the guard-ring isolated by Local Oxidation of Silicon (LOCOS) in the ESD event. Eventually, the ESD failure occurs at that comer of the guard-ring. The modified comer design of the guard-ring is proposed to resolve such ESD failure. The test chips designed by the proposed modification passed MM test over 200 V. Analyzing the test chips statistically, ESD immunity was increased over 20 % in MM mode test. In order to avoid such ESD failure, the automatic method to check the weak point in the guard-ring is also proposed by modifying the Design Rule Check (DRC) used in BCD technology. This DRC was used to check other similar products and 24 errors were found. After correcting the errors, the measured ESD level fulfilled the general industry specification such as HBM 2000 V and MM 200V.