• Journal of the Korea Organic Resources Recycling Association
• /
• v.18 no.3
• /
• pp.77-86
• /
• 2010

In this study, the model of the indirect wind suction waste sorting machine for characteristics of the screening of waste was studied using computational fluid dynamics and the drag coefficient for the model and the suction wind speed were obtained. The wind separator are developing by installing a cyclone air outlet to the suction blower impeller waste is selective in a way that does not pass the features and characteristics of the inlet pipe of the pressure loss and separation efficiency can have a significant impact on. Using Wind separator for selection of waste in the waste prior research on the aerodynamic properties are essential. For plastic cases, it is reasonable to take the drag coefficient between 0.8 and 1.0, and for cans, compression depending on whether the cans, the drag coefficient is in the range from 0.2 to 0.7. The separation efficiency of waste as change suction speed was the highest efficiency when the suction speed was 25~26 m/s. Shape of the inlet, depending on how the transfer pipe of the duct pressure loss occurs because the inlet velocity changes through the appropriate design standards to allow for continued research is needed.

• The Journal of Engineering Geology
• /
• v.20 no.3
• /
• pp.243-255
• /
• 2010

The slope design of an open-pit mine must consider economical efficiency and stability. Thus, the overall slope angle is the principal factor because of limited support or reinforcement options available in such a setting. In this study, slope displacement, as monitored by a GPS system, was analyzed for a coal mine at Pasir, Indonesia. Predictions of failure time by inverse velocity analysis showed good agreement with field observations. Therefore, the failure time of an unstable slope can be roughly estimated prior to failure. A GIS model that combines fuzzy theory and the analytical hierarchy process (AHP) was developed to assess slope instability in open-pit coal mines. This model simultaneously considers seven factors that influence the instability of open-pit slopes (i.e., overall slope gradient, slope height, surface flows, excavation plan, tension cracks, faults, and water body). Application of the proposed method to an open-pit coal mine revealed an enhanced prediction accuracy of failure time and failure site compared with existing methods.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.42 no.3
• /
• pp.169-178
• /
• 2006

This research aims at establishing the fundamental characteristics of the kite through the analysis of the flow field around various types of kites. The approach of this study were adopted for the analysis; visualization by CFD(computational fluid dynamics). Also, the lift/drag and PIV(particle image velocimetry) tests of kites had been performed in our previous finding. For this situation, models of canvas kite were designed by solidworks(design program) for the CFD test using the same conditions as in the lift/drag tests. And we utilized FloWorks as a CFD analysis program. The results obtained from the above approach are summarized as follows: According to comparison of the measured and analyzed results from mechanical tests, PIV and CFD test, the results of all test were similar. The numerical results of lift-coefficient and drag-coefficient were 5-20% less than those of the tests when attack angle is $10^{\circ},\;20^{\circ}\;and\;30^{\circ}$. In particular, it showed the 20% discrepancy at $40^{\circ}$. The numerical results of the ratio of drag and lift were 8-13% less than those of the tests at $10^{\circ}$ and 10% less than those of the tests at $20^{\circ},\;30^{\circ}\;and\;40^{\circ}$. Pressure distribution gradually became stable at $10^{\circ}$. In particular, the rectangular and triangular types had the centre of the high pressure field towards the leading edge and the inverted triangular type had it towards the trailing edge. The increase of the attack angle resulted in the eddy in order of the rectangular, triangular and inverted triangular type. The magnitude of the eddy followed the same order. The effect of edge-eddy was biggest in the triangular type followed by the rectangular and then the inverted triangular type. The action point of dynamic pressure as a function of the attack angle was close to the rear area of the model with the small attack angle, and with large attack angle, the action point was close to the front part of the model.

• Journal of Distribution Science
• /
• v.13 no.2
• /
• pp.105-112
• /
• 2015

Purpose - There is a recent social trend that is focused on the revitalization of business-founding. Business-founding now has an important impact on the progress of the national economy because of youth unemployment and an increase in baby-boom generation retirees. However, the support and infrastructure required for business-founding of the disabled are very insufficient. Since most supporting policies are on youth or middle-aged business-founding, business-founding by the disabled and the socially weak is losing competitiveness. Accordingly, this study diagnosed the issues by analyzing the current status of business-founding by the disabled and suggested a fostering direction for the advance of business-founding by the disabled. An idea for the founding of various business items is required for the competitiveness of business-founding by the disabled and the establishment of a growth-model based on marketing is required so that business-founding by the disabled would advance toward commercialization with growth potential. Research design, data, and methodology - Regarding the study method, the existing study literature on the status and issues in business-founding was mainly explored. In addition, the existing literature on the status and issues in business-founding by the disabled was also studied. The support on business-founding by the disabled by policy enforced by the 'Welfare Service Agency for the Disabled'and the support of related agencies including financial support on the commercialization of business-founding by the disabled were also examined. Results - Existing studies on business-founding by the disabled are very insufficient. It is very difficult to study a viable business-founding by the disabled fostering policy without thorough learning on the difficulties of business-founding by the disabled. Therefore, this study suggested a direction for the resolution of various issues such as market, funds, item, operational matters, and service by analyzing the difficulties in business-founding by the disabled until now. Particularly, this study suggested that building a commercialization model from the aspect of marketing strategy and the effort to change the growth aspect of the disabled into competitiveness are essential. Conclusions - This study examined the aspect of developing an item-development process for the growth and founding of disabled-owned businesses and the requirement of a government support system by multiple policies. Since the number of studies on business-founding by the disabled is very small, it is expected that this study would become an important study in the field of business-founding by the disabled. The revitalization of business-founding by the disabled substantially contributes to the progress of the state of the economy and continuous interest is required from the viewpoint of equal advance in the society. Success models in business-founding by the disabled should be created continuously and active publicizing of them to the disabled business-founders by analyzing the success cases would also be required. In addition, it is believed that a market entry strategy by way of a win-win strategy and cooperative relation with big companies should be also developed in the future.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.12 no.3
• /
• pp.167-173
• /
• 1979

It is preented the removable moving screen media-activated sludge (REMSMAS) process by using the biological fixed-film systems. The substrate removal kinetic difference between the aeration-only completed mixing activated sludge (CMAS) process and REMSMAS process were observed. The substrate removal kinetics were developed based on the attached and suspended microbial growths. The units of the aeration-only CMAS process were continously operated with the normal detention time of 4.5, 6, 9.5 and 12 flours studies after steady-state condition and the operating of the REMSMAS units conducted with the normal detention time of 6 and 12 hours studies in nonsteady-state condition. The feed solution was diluted 18 times to the raw starch wastewater in of order to maintain the proper COD (950mg/l) and BOD (450mg/l) concentration. Design parameters related to the suspended microbial growths were caculated by the equations used in the aeration-only CMAS model and these parameters used to evalute the kinetic constants in the REMSMAS process. The kinetic constant values of $Y_2,\;K_d,(\mu_{max})_s\;and\;K_s$ from Monod equations were respectively 0.78, 0.027/hr, 1.1/hr and 95mg/l in the aeration-only CMAS process. The value of the aera capacity (F) appeared to be $9.1\;mg/cm^2-day$ and the mean value of the saturation constant $(K_g)$ appeared to be 53.5 mg/l in the REMSMAs process. Also, the substrate removal .ate of the REMSMAS process was higher than that of the normal activated sludge process when this system was operated in steady-state condition. However, the rate was reduced as the critical operating day was approached.

• The Journal of the Korea Contents Association
• /
• v.9 no.11
• /
• pp.280-288
• /
• 2009

This study is to design and produce a detailed model for volume variety of three dimensional reconstruction images and to evaluate the changes of volume, area and the length of the model in the process of the reconstruction of RTP system. CT simulation was operated at the thickness of 1.25, 2.5, 5, 10mm and average, standard deviation of scan direction(X), thickness(Y), table movement direction(Z), area(A), and volume(V) of the three dimensional volume rendering, were measured according to the shape and thickness of the phantoms. As a result, at the thickness of 1.25, 2.5min, the phantom's shape decreased maximum 0.13cm(p<0.05) to the direction of X, Y, Z and length, area, volume decreased 0.1cm, $0.8cm^2$, $3.99cm^3$ which led to an approximate image of the phantoms. However, at the thickness of 5, 10mm, the phantom of the original form decreased maximum 0.58cm(p<0.05) and volume, area, length decreased maximum 0.45cm, $8.21cm^2$, $11.03cm^3$. Volume varieties according to the thickness and shape of the phantoms have occurred diversely, when CT simulation was operated, and it is considered that a clinically appropriate volume rendering can be obtained only when the thickness is below 3mm.

• Journal of the Korean Society for Railway
• /
• v.16 no.1
• /
• pp.7-13
• /
• 2013

A scaled version of a roller rig is developed to demonstrate the dynamic characteristics of a railway vehicle for academic purposes. This rig is designed based on Jaschinski's similarity law. It is scaled to 1/10 of actual size and allows 9-DOF motion to examine the up and down vibration of a train set. The test rig consists of three sub-hardware components: (i) a driving roller mechanism with a three-phase AC motor and an inverter, (ii) a bogie structure with first and second suspensions, and (iii) the vehicle body. The motor of the rig is capable of 3,600rpm, allowing the test to simulate a vehicle up to a maximum speed of 400Km/hr. Because bearings and joints are properly connected to the sub-structures, various motion analyses, such as a lateral, pitching, and yawing motion, are allowed. The slip motion between the rail and the wheel set is also monitored by several sensors mounted in the rig. After the construction of the hardware, an experiment is conducted to obtain the natural frequencies of the dynamic behavior of the specimen. First, the test rig is run and data are collected from six sets of accelerometers. Then, a numerical analysis of the model based on the ADAMS program is derived. Finally, the measurement data of the first three fundamental frequencies are compared to the analytical result and the validation of the test rig is conducted. The results show that the developed roller rig provides good accuracy in simulating the dynamic behavior of the vehicle motion. Although the roller rig designed in this paper is intended for academia, it can easily be implemented as part of a dynamic experiment of a bogie and a vehicle body for a high-speed train as part of the research efforts in this area.

• International Journal of Highway Engineering
• /
• v.7 no.4 s.26
• /
• pp.41-47
• /
• 2005

Traffic data such as traffic volume, speed, and vehicle Class are very important basic data for the plan and design of highway. Based on traffic data, the future service level of a specific highway and geometry of newly constructed or expended road is predicted and determined. The Ministry of Construction & Transportation has simultaneously surveyed coverage count and permanent count at highways since 1985. Traffic volume survey sections were determined at jointed nodes of highways and jointed nodes of highways and other roads such as freeway and local highway. Volume survey was performed at these sections. The premise to decide these sections is assumed that links between jointed nodes of main highways exhibit similar traffic characteristics. Recently, due to the change of highway geometries such as construction of detour road and installations of traffic facilities such as installation of media, traffic characteristics of the existing traffic volume survey sections was changed. To reflect these changes, traffic characteristics at homogeneous road sections was widely evaluated and analyzed. Using Genetic Algorithms, a model was developed for the evaluation of traffic characteristics at homogeneous road sections. Traffic volume survey sections were then determined through the application of the developed model for current traffic system.

• Journal of IKEEE
• /
• v.1 no.1 s.1
• /
• pp.31-46
• /
• 1997

In this paper, a parallel Optimal Best-First search Branch-and-Bound(B&B) algorithm(pobs) is designed and evaluated for MIN-based multiprocessor systems. The proposed algorithm decomposes a problem into G subproblems, where each subproblem is processed on a group of P processors. Each processor group uses tile sub-Global Best-First search technique to find a local solution. The local solutions are broadcasted through the network to compute the global solution. This broadcast provides not only the comparison of G local solutions but also the load balancing among the processor groups. A performance analysis is then conducted to estimate the speed-up of the proposed parallel B&B algorithm. The analytical model is developed based on the probabilistic properties of the B&B algorithm. It considers both the computation time and communication overheads to evaluate the realistic performance of the algorithm under the parallel processing environment. In order to validate the proposed evaluation model, the simulation of the parallel B&B algorithm on a MIN-based system is carried out at the same time. The results from both analysis and simulation match closely. It is also shown that the proposed Optimal Best-First search B&B algorithm performs better than other reported schemes with its various advantageous features such as: less subproblem evaluations, prefer load balancing, and limited scope of remote communication.

• Proceedings of the Korean Association of Geographic Inforamtion Studies Conference
• /
• 2003.04a
• /
• pp.472-477
• /
• 2003

멸종위기종의 서식지를 효율적으로 관리하기 위해서는 해당 종의 서식 가능한 지역의 분포를 알아야 한다. 본 연구의 목적은 GIS와 퍼지집합을 이용하여 산양(Nemorhaedus caudatus)의 서식지적합성모형을 개발하여 멸종 위기종의 서식지를 관리하기 위한 정보를 제공하는 것이다. 산양의 서식지적합성모형 개발을 위한 본 연구의 주요내용은 다음과 같다. 첫째, 산양 서식지 이용에 관한 기존 연구를 바탕으로 산양의 잠재적 서식지 환경변수를 분류하였으며, 분석 대상지의 산양 흔적 조사를 통해 서식지 환경변수의 재분류 및 x²검정(Chi-square test)을 통한 변수들의 유용성을 파악하고, 쌍체비교를 통한 환경변수별 가중치를 계산하였다. 둘째, 기존 부울논리(boolean logic)의 단점을 보완하기 위해 현장 조사의 결과를 바탕으로 퍼지논리(fuzzy logic)에 의한 산양 서식지의 각 환경변수별 주제도를 작성하고, 주제도들의 상관관계를 분석하여 상호 관련성이 높은 변수들의 중복을 피하였다. 셋째, 환경변수별 주제도와 변수별 가중치를 바탕으로 다기준평가기법(MCE, Multi-Criteria Evaluation)을 이용하여 분석대상지의 산양 서식지적합성모형을 개발하였다. 마지막으로, 개발된 서식지적합성모형의 타당성을 검증하기 위해 분석대상지 외부 지역을 대상으로 검증을 실시하였다. 분석 결과 분석대상지의 분류정확도는 서식가능성 0.5를 기준으로 93.94%의 매우 높은 분류정확도를 나타내었으며, 검증대상지에서는 95.74%의 분류정확도를 나타내어 본 모형의 분류정확도는 일관성이 높은 것으로 판단되었다. 또한 전체 공원구역에서 서식가능성 0.5이상의 면적은 59%를 차지하였다.퇴적이 우세한 것으로 관측되었다.보체계의 구축사업의 시각이 행정정보화, 생활정보화, 산업정보화 등 다양한 분야와 결합하여 보다 큰 시너지 효과와 사용자 중심의 서비스 개선을 창출할 수 있는 기반을 제공할 것을 기대해 본다.. 이상의 결과를 종합해볼 때, ${\beta}$-glucan은 고용량일 때 직접적으로 또는 $IFN-{\gamma}$ 존재시에는 저용량에서도 복강 큰 포식세로를 활성화시킬 뿐 아니라, 탐식효율도 높임으로써 면역기능을 증진 시키는 것으로 나타났고, 그 효과는 crude ${\beta}$-glucan의 추출조건에 따라 달라지는 것을 알 수 있었다.eveloped. Design concepts and control methods of a new crane will be introduced in this paper.and momentum balance was applied to the fluid field of bundle. while the movement of′ individual material was taken into account. The constitutive model relating the surface force and the deformation of bundle was introduced by considering a representative prodedure that stands for the bundle movement. Then a fundamental equations system could be simplified considering a steady state of the process. O