• Journal of the Korean Applied Science and Technology
• /
• v.16 no.2
• /
• pp.135-141
• /
• 1999

A synthesis of Dimer acid was studied from a tall oil fatty acid. Catalytic activity measured as reactant conversion in a autoclave reactor increase in accordance with the acidity. The optimization of process conditions were tested by an experimental design method. Optimization synthetic conditions of dimer acid and were reaction of tall oil fatty acid during 2 hour at $250^{\circ}C$, used of 7.3 wt% active clay and $1.2{\sim}1.4wt%$ water, and found reation pressure $8{\sim}9Kg/cm^2$. The maximum conversion rate was researched $74{\sim}76%$.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.6 no.4
• /
• pp.129-140
• /
• 1998

A numerical method is proposed to optimize automotive cam profiles. An acceleration curve of a cam follower motion is described by Hermite spline curves. Because of the intrinsic characteristics of the Hermite curve, it is possible to design an acceleration curve with arbitrary shape. Design variables in the optimization problem are location of control points which define the acceleration curve. Objective function includes dynamic performances as well as kinematic properties of a valve train. Similar optimization procedure was also performed using Polydyne cam profile synthesis method. Optimized profiles using the Hermite curve are proved to be superior to those using the Polydyne method.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.18 no.6
• /
• pp.576-584
• /
• 2009

Up to now, it has been said that no satisfactory computer solution has been found for synthesizing four-bar linkage based on the prescribed coupler link curve. In our study, an algorithm has been developed to improve the design synthesis of four bar linkage based on the 5 precision points method. The suggested algorithm generates the desired coupler curve by using NURBS, and then the generated curve approximates as closely as possible to the desired curve representing coupler link trajectory. Also, when comparing each generated curve by constructing the control polygon, rapid comparison is easily achieved by applying convex hull of the control polygon. Finally, an optimization process using ADS is incorporated into the algorithm based on the 5 precision point method to reduce the total optimization process time. As for examples, two four bar linkages were tested and the result well demonstrated the effectiveness of the algorithm.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.22 no.3
• /
• pp.454-468
• /
• 1997

This paper presents a bitwidth optimization algorithm for efficient hardware sharing in digital signal processing system. The proposed algorithm determines the fixed-point representation for each signal through bitwidth optimization to generate the hardware requiring less area. To reduce the operator area, the algorithm partitions the abstract operations in the design description into several groups, such that the operations in the same group can share an operator. The partitioning result are fed to a high-level synthesis system to generate the pipelined fixed-point datapaths. The proposed algorithm has been implemented in SODAS-DSP an automatic synthesis system for fixed-point DSP hardware. Accepting the models of DSP algorithms in schematics, the system automatically generates the fixed-point datapath and controller satisfying the design constraints in area, speed, and SNR(Signal-to-Noise Ratio). Experimental results show that the efficiency of the proposed algorithm by generates the area-efficient DSP hardwares satisfying performance constraints.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.24 no.11
• /
• pp.2665-2671
• /
• 2000

Dimensional Synthesis, which is apart of kinematic synthesis, is to determine the dimensions of a mechanism of preconceived typer for a specified task and prescribed performance. In this paper, in an effort to provide designers with flexibility, a dimensional approximate synthesis method is presented for utilizing prescribed tolerance both the displacement and joint positions of a mechanism to be synthesized. For this, a constrained optimization problem is formulated with displacement parameters and joint positions as variables. The proposed method is applied to the synthesis of a 5-SS multi link suspension mechanism. The method discussed here, however, can be easily applied to any mechanism of which the kinematic constraint equations can be derived.

• Aerospace Engineering and Technology
• /
• v.4 no.1
• /
• pp.25-30
• /
• 2005

The 4-bar linkage is the simplest model for the simulation of a retractable landing gear. In general, a designer uses a commercial software to design a linkage, which requires tedious iterations to obtain a good solution. By applying synthesis methodology the iteration process can be reduced remarkably. However, most of solutions obtained using synthesis process may not be an optimized solution. In this study, the characteristics of the optimization solution domain has been analyzed so that an optimization process can be adapted easily to a synthesis process.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.17 no.10 s.113
• /
• pp.1007-1019
• /
• 2006

In this paper, the synthesis method of multibeam radiation pattern with multi-directional beams and nulls is proposed. Genetic algorithm is applied for the optimization of amplitude and phase of the feeding signal into each element that is structured in planar array of single patch antenna with an arbitrary field distribution. To verify the validity of the proposed method, $2{\times}2$ planar array antenna is used for the measurement and the measured far field radiation pattern is compared with the simulation result. As a result, the synthesis of multibeam radiation pattern is implemented by the optimization of amplitude and phase of the feeding signal into each element of $8{\times}8$ planar array antenna system.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.16 no.3
• /
• pp.137-144
• /
• 2016

In this paper, we have proposed a circuit complexity optimization ILP algorithm of high-level synthesis system for new multiprocessor design. We have analyzed to the operator characteristics and structure of datapath in the most important high-level synthesis. We also introduced the concept of virtual operator for the scheduling of multi-cycle operations. Thus, we demonstrated the complexity to implement a multi-cycle operation of the operator, regardless of the type of operation that can be applied for commonly use in the ILP algorithm. We have achieved is that standard benchmark model for the scheduling of the 5th digital wave filter, it was exactly the same due to the existing datapath scheduling results.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.32 no.6
• /
• pp.34-48
• /
• 2004

In this paper an optimization algorithm is suggested to reduce the huge computation time in the optimum design of large structures, especially in spacecraft structures. It combines the coupled load analysis model using a constrained mode of component mode synthesis and the modal transient analysis. The computer simulation code is developed and evaluated in optimizing spacecraft platforms. The developed algorithm can alleviate the computational load with adequate accuracy. From the optimization of a spacecraft structural member, the characteristics of each structural member can be understood.

• 한국신재생에너지학회:학술대회논문집
• /
• 2011.05a
• /
• pp.74.2-74.2
• /
• 2011

A simulation study on synthesis gas process in GTL process was carried out in order to find optimum operation conditions for GTL (gas-to-liquid) pilot plant design. Optimum operating conditions for synthesis gas process were determined by changing reaction variables such as feed temperature and pressure. During the simulation, overall synthesis process was assumed to proceed under steady-state conditions. It was also assumed that physical properties of reaction medium were governed by RKS (Redlich-Kwong-Soave) equation. The effect of temperature and pressure on synthesis gas process $H_2$/CO ratio were mainly examined. Simulation results were also compared to experimental results to confirm the reliability of simulation model. Simulation results were reasonably well matched with experimental results.