• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.33A no.11
• /
• pp.140-151
• /
• 1996

In this study, we designed the routing structure and logic block of a SRAM cell-based FPGA with symmetrical-array architecture. The designed routing structure is composed of switch matrices, routing channels and I/O blocks, and the routing channels can be subdivided into single length channels, double length channels and global length channels. The interconnection between wires is made through SRAM cell-controlled pass transistors. To reduce the signal delay in pass transistors, we proposed a scheme raising the gate-control voltage to 7V. The designed SRAM cells have built-in shift register capability, so there is no need for separate shift registers. We designed SRAM cells in the LUTs(look-up tables) to enable the wirte operations to be performed synchronously with the clock for ease of system application. Each logic block (LFU) has four 4-input LUTs, flip-flops and other gates, and the LUTs can be used a sSRAM memory. The LFU also has a dedicated carry logic, so a 4-bit adder can be implemented in one LFU. We designed our FPGA using 0.6.mu.m CMOS technology, and simulation shows proper operation of a 4 bit counter at 100MHz.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.10 no.2
• /
• pp.237-246
• /
• 1999

A miniaturized waveguide bandpass filter is designed by combining a corrugated lowpass structure and a highpass configuration based on the cut-off effect of waveguides. It is smaller than the conventional waveguide bandpass filter composed of half-wavelength resonators and has wider spurious free characteristics. Optimized design data for a seven-order waveguide bandpass filter with the symmetrical structure are given at the center frequency of 10 GHz with 800 MHz bandwidth. Measured bandwidth of the center frequency of 9.97 GHz is 840 MHz and measured insertion loss is 0.97dB, The length of the bandpass filter is 64.38mm. The first spurious response is produced at 26.1 GHz.

• Journal of the Korea Society of Computer and Information
• /
• v.8 no.2
• /
• pp.88-96
• /
• 2003

Microstrip line is one of the most essential elements of microwave and milimeter-wave integrated circuits. And then the frequency dependent characteristics of the microstrip line have previously been analyzed using several frequency domain approaches But the 3-D TLM method presented in this Paper is another independent approaches for obtaining frequency domain results for microstrip line. The structure analysed with this TLM algorithm is step discontinuity microstrip line and the symmetrical condensed node is used. After numerical analysis, the frequency dependent scattering Parameters of a step discontinuity microstrip line have been calculated by Fourier transform of the time domain data. From the time domain TLM numerical results. this numerical analysis is shown to be an efficient method for modelling complicated structure as step discontinuity microstrip line.

• Proceedings of the KIEE Conference
• /
• 1995.07b
• /
• pp.871-873
• /
• 1995

The purpose of this paper is to design and construct the compact type joint driver and controller of the biped robot. This biped robot will be designed to be suitable for the practical usages and applications in the work environment, which is not plat floor, like a stairs by taking the stand-alone style that equipped all the parts except power sources. Generally, highly nonlinear motion dynamics of the biped robot is realized to linear approximations by installing a high-ratio speed reducer at each joint and dividing motions into a several piecewise linear motions, which is realized by the digital controller design techniques. This biped robot has symmetrical structure to get the stable walking ability and also the hierachical structure to control each joint as well. That is, all of the joint controllers are connected to the main controller in the composition of overall controllers. The driver and controller of each joint uses PI controller that compensate the velocity and position errors by the data of the encoder. And the signal characteristics of each joint controller forms a trapezoid speed profile which is predefined by the values of direction, maximum velocity and position.

• Structural Engineering and Mechanics
• /
• v.56 no.5
• /
• pp.787-796
• /
• 2015

When the temperature of a structure varies, there is a tendency to produce changes in the shape of the structure. The resulting actions may be of considerable importance in the analysis of the structures having non-prismatic members. The computation of design forces for the non-prismatic beams having symmetrical parabolic haunches (NBSPH) is fairly difficult because of the parabolic change of the cross section. Due to their non-prismatic geometrical configuration, their assessment, particularly the computation of fixed-end horizontal forces and fixed-end moments becomes a complex problem. In this study, the efficiency of the Artificial Neural Networks (ANN) and Adaptive Neuro Fuzzy Inference Systems (ANFIS) in predicting the design forces and the design moments of the NBSPH due to temperature changes was investigated. Previously obtained finite element analyses results in the literature were used to train and test the ANN and ANFIS models. The performances of the different models were evaluated by comparing the corresponding values of mean squared errors (MSE) and decisive coefficients ($R^2$). In addition to this, the comparison of ANN and ANFIS with traditional methods was made by setting up Linear-regression (LR) model.

• Journal of Power Electronics
• /
• v.18 no.6
• /
• pp.1920-1929
• /
• 2018

In order to provide a source for nine phases suitable for 18-pulse ac to dc power, this paper proposes a new structure for a step-up asymmetrical delta-connected transformer for converting three-phase ac power to nine-phase ac power. The design allows for symmetry between the nine output voltages to improve the power quality of the supply current and to minimize the THD. The results show that this new structure proves the equality between the output voltages with $40^{\circ}-{\alpha}$ and $40^{\circ}+{\alpha}$ phase shifting and produces symmetrical output currents. This result in the elimination of harmonics in the network current and provides a simulated THD that is equal to 5.12 %. An experimental prototype of the step-up asymmetrical delta-autotransformer is developed in the laboratory and the obtained results give a network current with a THD that is equal to 5.35%. Furthermore, a finite element analysis with a 3D magnetic field model is made based on the dimensions of the 4kVA, 400 V laboratory prototype three-phase with three-limb delta-autotransformer with a six-stacked-core in each limb. The magnetic distribution flux, field intensity and magnetic energy are carried out under open-circuit operation or load-loss.

• The Bulletin of The Korean Astronomical Society
• /
• v.44 no.1
• /
• pp.50.2-50.2
• /
• 2019

Understanding three-dimensional structure and parameters (e.g., radial velocity, angular width, source location and density) of coronal mass ejections (CMEs) is essential for space weather forecast. In this study, we determine CME mean density in solar corona and near the Earth. We select 38 halo CMEs, which have the corresponding interplanetary CMEs (ICMEs), by SOHO/LASCO from 2000 to 2014. To estimate a CME volume, we assume that a CME structure is a full ice-cream cone which is a symmetrical circular cone combined with a hemisphere. We derive CME mean density as a function of radial height, which are approximately fitted to power-law functions. The average of power-law indexes is about 2.1 in the LASCO C3 field of view. We also obtain power-law functions for both CME mean density at 21 solar radii and ICME mean density at 1AU, with the average power-law index of 2.6. We estimate a ratio of CME density to background density based on the Leblanc et al.(1998) at 21 solar radii. Interestingly, the average of the ratios is 4.0, which is the same as a default value used in the WSA-ENLIL model.

• Structural Engineering and Mechanics
• /
• v.77 no.1
• /
• pp.57-74
• /
• 2021

The thermal eigenvalue responses of the graded sandwich shell structure are evaluated numerically under the variable thermal loadings considering the temperature-dependent properties. The polynomial type rule-based sandwich panel model is derived using higher-order type kinematics considering the shear deformation in the framework of the equivalent single-layer theory. The frequency values are computed through an own home-made computer code (MATLAB environment) prepared using the finite element type higher-order formulation. The sandwich face-sheets and the metal core are discretized via isoparametric quadrilateral Lagrangian element. The model convergence is checked by solving the similar type published numerical examples in the open domain and extended for the comparison of natural frequencies to have the final confirmation of the model accuracy. Also, the influence of each variable structural parameter, i.e. the curvature ratios, core-face thickness ratios, end-support conditions, the power-law indices and sandwich types (symmetrical and unsymmetrical) on the thermal frequencies of FG sandwich curved shell panel model. The solutions are helping to bring out the necessary influence of one or more parameters on the frequencies. The effects of individual and the combined parameters as well as the temperature profiles (uniform, linear and nonlinear) are examined through several numerical examples, which affect the structural strength/stiffness values. The present study may help in designing the future graded structures which are under the influence of the variable temperature loading.

• ETRI Journal
• /
• v.45 no.2
• /
• pp.338-345
• /
• 2023

A filtering power divider based on air-filled substrate-integrated waveguide (AFSIW) technology is proposed in this study. The AFSIW structure is used in the proposed filtering power divider for substantially reducing the transmission losses. This structure occupies a large area because of the use of air as a dielectric instead of typical dielectric materials. A filtering power divider provides power division and frequency selectivity simultaneously in a single device. The proposed filtering power divider comprises three AFSIW cavities. The filtering function is achieved using symmetrical inductive posts. The input and output ports of the proposed circuit are realized by directly connecting coaxial lines to the AFSIW cavities. This transition from the coaxial line to the AFSIW cavity eliminates the additional transitions, such as AFSIW-SIW and SIW-conductor-backed coplanar waveguide, applied in existing AFSIW circuits. The proposed power divider with a second-order bandpass filtering response is fabricated and measured at 5.5 GHz. The measurement results show that this circuit has a minimum insertion loss of 1 dB, 3-dB fractional bandwidth of 11.2%, and return loss exceeding 11 dB.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.22 no.1
• /
• pp.252-264
• /
• 2023

This paper proposes a design of a dual-band band-pass filter that integrates a λg/2 open SIR structure, a transmission line, and a fork-type structure with symmetric and asymmetric open stubs. To obtain the dual-band effect, the proposed filter uses the SIR structure and adjusts the impedance ratio of the SIR structure. Therefore, the position of the harmonics of the filter is shifted through the adjustment of the impedance ratio, and this can obtain a double-band effect. In order to obtain the dual-band characteristics, the dual-band effect is obtained by inserting a open stub between the SIR structures with the SIR structure divided in half. In addition, the second frequency response is obtained by adjusting the length of the open symmetrical stub in the fork-shaped structure. The asymmetrical open stub in the fork form achieves optimum bandwidth by adjusting the length. Therefore, the first center frequency of the proposed band-pass filter is 5.896 GHz and the bandwidth is 13.6 %. At this time, the measurement results are 0.13 dB and 33.6 dB. The second center frequency is 5.906 GHz and the bandwidth is 13.6 %. At this time, the measurement results are 0.15 dB and 19.8 dB. The reason is that when the impedance ratio (Δ) is higher than 1, the position of the harmonic is shifted to a lower frequency band. However, if the impedance ratio (Δ) is lowered by one step, the position of harmonics will move to a higher frequency band. The function of the filter designed using these characteristics can be obtained from the measurement result. The proposed band-pass filter has no coupling loss and no via energy concentration loss because there is no coupling structure of input/output and no via hole. Therefore, system integration is possible due to its excellent performance, and it is expected that dedicated short-range communication (DSRC) system applications used in traffic communication systems will be possible.