• Bulletin of the Korean Chemical Society
• /
• v.16 no.2
• /
• pp.189-190
• /
• 1995

• Journal of Power Electronics
• /
• v.6 no.4
• /
• pp.330-339
• /
• 2006

This paper deals with novel electronic ballast based on single-stage power processing topology using a symmetrical half-bridge inverter and current injection circuit. The half-bridge inverter drives the output parallel resonant circuit and injects current through the power factor correction (PFC) circuit. Because of high frequency current injection and high frequency modulated voltage, the proposed circuit maintains the unity power factor (UPF) with low THD even under wide variation in ac input voltage. This circuit needs minimum and lower sized components to achieve the UPF and high efficiency. This leads to an increase in reliability of ballast at low cost. Furthermore, to reduce cost, the electronic ballast is designed for two series-connected fluorescent lamps (FL). The analysis and experimental results are presented for ($2{\times}36$ Watt) fluorescent lamps operating at 50 kHz switching frequency and input line voltage (230 V, 50 Hz).

• Proceedings of the KIEE Conference
• /
• 2002.07b
• /
• pp.694-696
• /
• 2002

Transformers together with all equipment and accessories shall be designed and constructed to withstand the mechanical and thermal stresses produced by external short circuit which include three phase, single line-to-ground, double line-to-ground and line-to-line faults etc. Generally the Short Circuit Test of transformers is tested according to the ANSI/IEEE, IEC/JEC, KS etc, in domestic. In this study, it will be showed and compared the difference of symmetrical current for short circuit test of a Pad -mounted transformer according to with ANSI /IEEE and IEC.

• Transactions on Electrical and Electronic Materials
• /
• v.10 no.2
• /
• pp.44-48
• /
• 2009

A simulation study of a 10-bit two-stage DAC was done by using a conventional current switch cell. The DAC adopts the segmented architecture in order to reduce the circuit complexity and the die area. The 10-bit CMOS DAC was designed in 2 blocks, a unary cell matrix for 6 MSBs and a binary weighted array for 4 LSBs, for fabrication in a 0.35-${\mu}m$ CMOS process. To cancel the accumulation of errors in each current cell, a symmetrical switching sequence is applied in the unary cell matrix for 6 MSBs. To ensure high-speed operation, a decoding circuit with one stage latch and a cascode current source were developed. Simulations show that the maximum power consumption of the 10-bit DAC is 74 mW with a sampling frequency of 100 MHz.

• Bulletin of the Korean Chemical Society
• /
• v.31 no.5
• /
• pp.1326-1330
• /
• 2010

Evidences have proved the versatile role of sulfur atom in supramolecular chemistry. $^1$Presence of S atom in the molecule usually results in the specific structural properties of molecules. In the present study, $S{\cdots}arene$, $N{\cdots}arene$, $CH{\cdots}{\pi}$, $CH{\cdots}S$ and $CH{\cdots}N$ type of weak interactions stabilize the conformation and self assembly of symmetrical as well as dissymmetrical molecules.

• Proceedings of the KIEE Conference
• /
• 2001.11a
• /
• pp.216-218
• /
• 2001

This paper deals with the control of magnetic field around the down conductor of lightning protection systems. The magnetic field strength in the vicinity of down conductor is shown to drop off rapidly with distance from the down conductor and is reversely proportional to the number of down conductor. Also the magnetic field strength is decreased in the structures as the down conductor is installed with the symmetrical arrangement, and it is zero at the center of symmetry. The magnetic field strengths for the symmetrical arrangement of two down conductors are less than one half compared with that for a down conductor. A proper arrangement of down conductor can reduce or cancel the magnetic field in a restricted place where information-oriented and computerized facilities are densely installed.

• Proceedings of the IEEK Conference
• /
• 2002.07a
• /
• pp.401-404
• /
• 2002

This paper proposes a new symmetrical bandpass filter based on capacitive loading with a coplanar waveguide (CPW) structure. The filter was numerically designed at the operating frequency around 2 ㎓ by using IE3D software package. The characteristics of the proposed filter were then measured which the results were in good agreement with simulation. The passband insertion loss was considerably low (~3 ㏈) and the return loss was high (greater than 10 ㏈). The size of the proposed filter was also decreased approximately 50% when comparing with the fitters using conventional transmission lines.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.18 no.8
• /
• pp.664-671
• /
• 2006

We propose the correlation to predict the spreading thermal resistance on a plate with symmetrical four heat sources. The correlation transforms four heat sources to a single equivalent heat source and then the spreading thermal resistance can be obtained with the existing equation for a single heat source. When the four heat sources are mounted on a square base plate, the correlation is expressed as a function of the heat source size, the length of base plate, the plate thermal conductivity and the distance between heat sources. Compared to the results of three-dimensional numerical analysis, the spreading thermal resistance by the proposed correlation is in good agreement within 10 percent accuracy.

• Transactions of Materials Processing
• /
• v.15 no.7 s.88
• /
• pp.479-484
• /
• 2006

The evolution of strain states and textures during rolling with various conditions was investigated by finite element method (FEM) simulations and measurements of rolling textures. Symmetrical rolling with a high friction gives rise to a strong variation of shear strains in rolled sample leading to the formation of texture gradients throughout the thickness layers. A small variation of shear strains during rolling with a well lubrication condition leads to the formation of a fairly homogeneous rolling texture throughout the sheet thickness. During asymmetrical rolling, a proper control of rolling parameters provides the evolution of a fairly homogeneous shear texture throughout the whole sheet thickness.

• 유체기계공업학회:학술대회논문집
• /
• 2002.12a
• /
• pp.433-438
• /
• 2002

The flow field around a symmetrical airfoil in a uniform flow under the generation of noise was numerically studied and compared with experimental datum. The numerical simulation was carried out by LES which employs a deductive dynamic model as subgrid-scale model. The result of an attack angle of $6^{\circ}$ indicate that the discrete frequency noise is generated when the separated laminar flow reattaches near the trailing edge of the pressure side and the turbulent boundary layer is formed over the suction side of the airfoil near the trailing edge. The periodic behavior of vortex formation was observed around the trailing edge and it persists further downstream in the wake. The frequency of the vortex formation in the wake was consistent with that of the discrete frequency noise.