• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.56 no.11
• /
• pp.1995-1997
• /
• 2007

In this paper we propose a wavelength-switchable fiber ring laser that employs a polarization-dependent fiber band stop filter. The fiber filter was fabricated by inscribing a long-period fiber grating on a high birefringent fiber. Dual-wavelength switching operation was accomplished by controlling the rotatable linear polarizer which rotated the polarization plane of the light circulating through the fiber laser cavity. The amplitude variation of both laser lines was measured to be less than 0.5 dB and the signal-to-amplified spontaneous emission ratio was more than 55 dB.

• ETRI Journal
• /
• v.29 no.5
• /
• pp.688-690
• /
• 2007

This letter presents a filter for a car navigation system integrating a low-grade inertial measurements unit (IMU) and a global positioning system receiver. The filter is designed according to the state variables to be estimated and the usable measurements. The usable measurements change from case to case, and the estimative state variables also change due to the measurements; therefore, multiple models must be used for real environmental maneuvers. In this letter, four models for land navigation are chosen and switched by rearranging the system matrix and resetting the error covariance matrices.

• Korean Journal of Optics and Photonics
• /
• v.12 no.5
• /
• pp.401-405
• /
• 2001

We propose a novel channel-switching transmission filter using segmented chirped fiber Bragg gratings (CFBG's) each of which has separate transmission bands in the reflection spectrum of the CFBG. The segmented CFBG's are made by using specially designed slits. The separated reflection spectral bands of the segmented CFBG's are controlled by the attached fiber stretchers, and the controlled reflection bands are used to choose the channels independently. Tunability of the transmission spectra is experimentally demonstrated in WDM transmission experiments.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.29 no.3
• /
• pp.69-80
• /
• 2015

This paper is writing about developing magnet power supply. It is very important for power supply to obtain output current in high precision and high stability. As a switching noise and a power noise are the cause of disrupting the stability of output current, to remove these at the front end, low pass filter with 300Hz cutoff frequency is designed and placed. And also to minimize switching noise of the current into magnet and to stop abrupt fluctuations, output filter should be designed, when doing this, we design it by considering load has high value inductance. As power supply demands the stability of less than 5ppm, high precision 24bit(300nV/bit) analog digital converter is needed. As resolving power of 24bit(300nV/bit) analog digital converter is high, it is also very important to design the input stage of analog digital converter. To remove input noise, 4th order low pass filter is composed. Due to the limitation of clock, to minimize quantization error between 15bit DPWM and output of ADC having 24bit resolving power, ${\Sigma}-{\Delta}$ modulation is used and bit contracted DPWM is constituted. And before implementing, to maximize efficiency, simulink is used.

• Journal of Electrical Engineering and Technology
• /
• v.11 no.2
• /
• pp.405-415
• /
• 2016

This paper presents a model predictive control for shunt active power filters in synchronous reference frame using space vector pulse-width modulation (SVPWM). The three phase load currents are transformed into synchronous rotating reference frame in order to reduce the order of the control system. The proposed current controller calculates reference current command for harmonic current components in synchronous frame. The fundamental load current components are transformed into dc components revealing only the harmonics. The predictive current controller will add robustness and fast compensation to generate commands to the SVPWM which minimizes switching frequency while maintaining fast harmonic compensation. By using the model predictive control, the optimal switching state to be applied to the next sampling time is selected. The filter current contains only the harmonic components, which are the reference compensating currents. In this method the supply current will be equal to the fundamental component of load current and a part of the current at fundamental frequency for losses of the inverter. Mathematical analysis and the feasibility of the suggested approach are verified through simulation results under steady state and transient conditions for non-linear load. The effectiveness of the proposed controller is confirmed through experimental validation.

• Journal of Electrical Engineering and Technology
• /
• v.10 no.5
• /
• pp.2197-2204
• /
• 2015

In recent years, medical image diagnosis has growing significant momentous in the medicinal field. Brain and lung image of patient are distorted with salt and pepper noise is caused by moving the head and chest during scanning process of patients. Reconstruction of these images is a most significant field of diagnostic evaluation and is produced clearly through techniques such as linear or non-linear filtering. However, restored images are produced with smaller amount of noise reduction in the presence of huge magnitude of salt and pepper noises. To eliminate the high density of salt and pepper noises from the reproduction of images, a new efficient fuzzy based median filtering algorithm with a moderate elapsed time is proposed in this paper. Reproduction image results show enhanced performance for the proposed algorithm over other available noise reduction filtering techniques in terms of peak signal -to -noise ratio (PSNR), mean square error (MSE), root mean square error (RMSE), mean absolute error (MAE), image enhancement factor (IMF) and structural similarity (SSIM) value when tested on different medical images like magnetic resonance imaging (MRI) and computer tomography (CT) scan brain image and CT scan lung image. The introduced algorithm is switching filter that recognize the noise pixels and then corrects them by using median filter with fuzzy two-sided π- membership function for extracting the local information.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.23 no.2
• /
• pp.129-138
• /
• 2018

Previous single-phase transformerless inverters used active bypass switching circuits that need auxiliary power switches to minimize ground leakage current. However, switching and gate driving losses are increased due to the use of additional power switches. To cope with this drawback, this work proposes a transformerless inverter using a passive bypass filter without any auxiliary power switch. The operation and control of the proposed inverter are described. The ground leakage current characteristics are analyzed for the proposed inverter with the passive bypass filter. The experimental results of the proposed inverter for a 1.0kW prototype system are presented.

• Journal of Institute of Control, Robotics and Systems
• /
• v.14 no.2
• /
• pp.133-140
• /
• 2008

In this paper, a small and effective attitude estimation system for a humanoid robot was developed. Four small inertial sensors were packed and used for inertial measurements(3D accelerometer and three 1D gyroscopes.) An effective 3D pose estimation algorithm for low cost DSP using an extended Kalman filter was developed and evaluated. The 3D pose estimation algorithm has a very simple structure composed by 3 modules of a linear acceleration estimator, an external acceleration detector and an pseudo-accelerometer output estimator. The algorithm also has an effective switching structure based on probability and simple feedback loop for the extended Kalman filter. A special test equipment using linear motor for the testing of the 3D pose sensor was developed and the experimental results showed its very fast convergence to real values and effective responses. Popular DSP of TMS320F2812 was used to calculate robot's 3D attitude and translated acceleration, and the whole system were packed in a small size for humanoids robots. The output of the 3D sensors(pitch, roll, 3D linear acceleration, and 3D angular rate) can be transmitted to a humanoid robot at 200Hz frequency.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2016.05a
• /
• pp.397-400
• /
• 2016

In digital images, the addition due to noise occurs in the process of obtaining, saving, and transmitting. For examples of noise, there are salt and pepper noise, Gaussian noise, and composition noise where various noises are mixed. Existing filters have insufficient noise removal characteristics because it uses single filters in composite noise environment. Therefore the study suggested a switching filter that processes with special weighted value and median filter according to local mask salt and pepper noise density when central pixel is damaged by salt and pepper noise, and processes by applying weighted values differently according to standard deviation of local mask when damaged by Gaussian noise.

• Proceedings of the KIPE Conference
• /
• 2001.10a
• /
• pp.236-241
• /
• 2001

This paper presents a novel prototype of active voltage-clamping capacitor-assisted edge resonant soft switching PWM inverter operating at a constant frequency variable power (VPCF) regulation scheme, which is suitable for consumer high-power induction-heating cooking appliances. New generation IGBT with a trench gate is particularly improved in order to reduce conduction loss due to its lowered saturation voltage characteristics. The soft switching load resonant and quasi-resonant inverter designed distinctively using the latest IGBTs is evaluated from an experimental point of view.