• Nuclear Engineering and Technology
• /
• v.55 no.6
• /
• pp.1999-2010
• /
• 2023

Undesirable flapping motion of discs can cause the failure of swing check valves in nuclear passive safety systems. Time-resolved particle image velocimetry (PIV) was employed to investigate the flow characteristics around a free-to-rotate plate and the motion response, with the Reynolds numbers, based on the hydraulic diameter of the channel, from 1.32 × 10⁴ to 3.95 × 10⁴. Appreciable flapping motion (±3.52°) appeared at the Reynolds number of 2.6 × 10⁴ with the frequency of 5.08 Hz. In the low-Reynolds-number case, the plate showed negligible flapping. In the high-Reynolds-number case, the deflection angle increased with reduced flapping amplitude. The torque from the fluid determined the flapping amplitude. In the low-Reynolds-number case, Karman vortices were absent. With increasing Reynolds numbers, Karman vortices developed behind the plate with larger deflection angles. Strong interaction between the wake flow from the leading and trailing edge of the plate was observed. Based on power spectrum density (PSD) analysis, the vortex shedding frequency coincided with the flapping frequency, and the amplitude was positively correlated to the strength of the vortices. Proper orthogonal decomposition (POD) modes evince that, in the case of appreciable motion, coherent structures exhibited a larger spatial scale, enhancing the magnitude of the external torque on the plate.

• Journal of Drive and Control
• /
• v.19 no.2
• /
• pp.11-16
• /
• 2022

It is important to measure the excavator's work productivity that estimates the bucket's payloads on a process. If the bucket isn't filled at every working cycle, the excavator's operator has to drive the machine more to achieve his work quota. If bucket is filled over with the load, the other way around, the transferred object has to spread out on the workplace. That causes additional work to clean the site. This paper proposes a method that can estimate the bucket's payload to improve the excavator's work productivity. This method assumes that the excavator is a lumped mass system. And it uses a 3 points angle (boom link, arm link, swing) and 2 points pressure (boom cylinder's input port and output port) of measurable data. Depending on assumptions, the bucket's payload can be calculated by the payload's motion equation. And this suggested method can be verified by simple experiments.

• Journal of Korean Physical Therapy Science
• /
• v.10 no.1
• /
• pp.90-101
• /
• 2003

Gait analysis can provide a better understanding of how the alignment of the lower limb and foot can contribute to force observed at the knee. Anatomic and mechanical factors that affect loading in the knee pint can contribute to pathologic change seen at the knee in degenerative pint disease and should be considered in treatment plan. The purpose of this study is to present the gait analysis data and to determine whether there is any relationships between alignment of the lower limb, foot progression angle and knee pint moments in elderly healthy women with 3-dimensional motion analyzer. The results were as follows; 1. Cadence showed 114.8 steps/min, gait speed showed 1.05 m/s, time per a stride showed 1.06 sec, time per a step showed 0.53 sec, single-supporting phase was 0.41 sec, double-supporting phase was 0.24 sec, stride length was 1.04 m, Step length was 0.56 m. 2. According to the parameters of kinematics, the maximal knee flexion angle through swing phase showed left $46.82^{\circ}$, right $40.19^{\circ}$ and the maximal knee extension angle showed left $-1.32^{\circ}$, right $2.01^{\circ}$. knee varus showed left $26.90^{\circ}$, right $30.93^{\circ}$. 3. Moment, one of kinetic parameters of knee pint the maximal flexion moment showed left 0.363. Nm/kg, right 0.464 Nm/kg and maximal extension moment showed left 0.389 Nm/kg, right 0.463 Nm/kg. The maximal. adduction moment showed left 0.332 Nm/kg, right 0.379 Nm/kg and the maximal internal rotatory moment showed left 0.13 Nm/kg, right 0.140 Nm/kg. 4. On sagittal plane, the maximal power of knee joint showed left 0.571 J/kg, right 0.629 J/kg. On coronal plane, the maximal power of knee joint showed left 0.11 J/kg, right 0.12 J/kg. On transverse plane, the maximal power of knee joint showed left 0.058 J/kg, right 0.072 J/kg. 5. The subject who had varus alignment of the lower extremity had statistically higher in knee adduction moment in mid stance phase. 6. The subject who had large foot progression angle had statistically lower in knee adduction moment in late stance phase. A relationship was observed between the alignment of the lower extremity and the adduction moment of the knee joint during stance phase. Hence, we need some research to figure, out the change of adduction moment according to the sort of knee joint osteoarthritis and the normal geriatrics as well. And we also require more effective, specific therapeutic program by making use of those background of researches.

• Archives of design research
• /
• v.17 no.4
• /
• pp.141-148
• /
• 2004

The purpose of this study is to define the emotion that expressed in step animation and to quantify the intuitional expression of emotion that related step for using extract, measure, analysis the stimulate element about step. The survey of relation with 27 word of emotional expressions and 36 moving pictures of step sample is used for method of this test. The emotional mental structure is transferred to 2 dimensional planes as applying the results of analysis of integrated data using Quantification Method 3, which the integrated data is composed two axial - confidential axial and stabling axial. Analysis of distribution of 2 dimensional diagram shows that the second of the plane and the third of the plane have much data. However, the first of the plane and the forth of the plane have a little data. Through this kind of analysis of graph, it is difficult to express a different emotion between unstable the timidity mind and stable feel the timidity mind using only step analysis. Six difference types about physical elements affecting to emotion are selected and analyzed such as the paces of step, the rate of step, the movement angle of pelvis, the swing range of arm, angle of backbone and the lean angle of body. The result is that the rate of stop and the lean angle of body are the major element that effects to emotional stimulate of stop. This thesis argues about methods transforming subjective expression to objective and quantitative expression with the state of delicate emotion of character apply to step animation naturally. Those data to apply to multi-contents in future are the main target in this study.

• Korean Journal of Applied Biomechanics
• /
• v.12 no.2
• /
• pp.159-177
• /
• 2002

The purpose of this study was to investigate the relations between the segments of the body, the three dimensional anatomical angle and the angular velocity of the air born phase and understand the control mechanism of the high-bar movement, the somersault, the double somersault, the double somersault with full twist. For this study seven well trained university gymnastic volunteered, Zatsiorky and Seluyanov(1983, 1985)'s sixteen segment system anatomical model was used for this study. For the movement analysis three dimensional cinematographical method(Arial Performance Analysis System : APAS) was used and for the calculation of the kinematic variables a self developed program was used with the LabVIEW 5.1 graphical profromming(Johnson, 1999) program. By using Eular's equations the three dimensional anatomical Cardan angles of the joint and angular velocity were defined. As a result of this study 1. As the rotation of the body increased in the air born phase the projection angle of the CM of the total increased, this resulted the increased of the max hight of the CM. 2. In three dimensional angular velocity the Z axis(vertical direction) projection angular velocity increased as the rotation of the body increased in the airborn phase, but the Y axis and the X axis projection angular velocity did not show significant differences. 3. As the rotation of the body increased in the air born phase the angular movement of the shoulder and the hip showed significant change. These movement act as the starter in the preparation phase. 4. The somersault angle, the twist angle, the tilt angle of the upper body related to the global reference frame in the releas phase the average somersault angle of the three types of high-bar movement was $57.7^{\circ}$, $38.8^{\circ}$, $39.7^{\circ}$, the average tilt angle was $-1.5^{\circ}$, $-5.4^{\circ}$, $-8.4^{\circ}$, the average twist angle was $13.4^{\circ}$, $10.6^{\circ}$, $23.3^{\circ}$. This result showed that the somersault with full twist had the largest movement.

• Journal of rehabilitation welfare engineering & assistive technology
• /
• v.7 no.2
• /
• pp.75-84
• /
• 2013

In this study, the patterns and characteristics according to gait cycle were analyzed using to EMG signals during walking, and analyzed in the time domain and frequency domain. The experiments was performed divide to level-ground walking and stair walking, and gait cycle was analysis by stance and swing. In the sagittal plane by using the tilt sensor measures the angle of the lower leg, and EMG was measured from the quadriceps and biceps femoris. The tilt of the lower leg was showed the biggest tilt at HS, and showed lowest value at TO. All in walking according to the gait cycle IEMG showed a specific pattern, and is expected useful to determine the gait cycle and kind. In the frequency domain analysis was using STFT on able to frequency analysis according to time, and using the tilt sensor was identify gait cycle. We analyzed also spectrum of the results of the STFT in all gait types, and recognized that stance had broad bandwidth than that of swing. Through this study, it was confirmed the possibility of judgment and analysis of the gait cycle using EMG and the tilt in the sagittal plane of the lower leg. When used it, can improve the quality of life of amputation patients

• The Journal of Korean Physical Therapy
• /
• v.17 no.4
• /
• pp.633-650
• /
• 2005

The aim of this study was to investigate the kinematics of young adults during ascent ramp climbing at different inclinations. Twenty-three subjects ascended a four step at four different inclinations(level, $8^{\circ},\;16^{\circ},\;24^{\circ}$). The 3-D kinematics was analysed by a camera-based falcon system. Groups difference was tested with one -way ANOVA and SNK test. The different kinematic patterns of ramp ascent were analysed and compared to level walking patterns. The kinematics of ramp walking could be clearly distinguished from the kinematics of level walking. In sagittal plane, Ankle joint was more dorsiflexed at initial contact and Max. dorsiflex. during stance phase with $16^{\circ},\;24^{\circ}$ inclination and more plantarflexed at toe off and Max. plantarflex. during swing phase with $24^{\circ}$(p<.001). Knee joint was more flexed at initial contact with $16^{\circ},\;24^{\circ}$ inclination(p<.001). Hip joint was more flexed at initial contact and Max. flex. during swing phase with $16^{\circ},\;24^{\circ}$ inclination and at toe off with $24^{\circ}$(p<.001) and was more extended at Max. ext. during stance phase with $24^{\circ}$(p<.05). In frontal plane, ankle joint was more everted at Max. eversion. during stance phase with $16^{\circ},\;24^{\circ}$ inclination(p<.001). Knee joint was more increased at Max. varus. during stance phase with $16^{\circ},\;24^{\circ}$ inclination(p<.001). Hip joint was not differentiated with different inclinations. In horizontal plane, all joints were not differentiated with different inclinations. Conclusionally, In ascent ramp walking, the different gait pattern generally occurred at over $16^{\circ}$ on the ascending ramp in sagittal and frontal plane. These results suggest that there is a certain inclination angle or angular range where subjects do switch between a level walking and a ascent ramp walking gait pattern. This shows their motor control strategy between level and ascent ramp walking. Further studies are necessary to confirm and detect the ascent ramp gait patterns.

• The Journal of the Korean bone and joint tumor society
• /
• v.3 no.1
• /
• pp.18-25
• /
• 1997

Prosthetic replacement is one of the most common methods of reconstruction after resection of malignant tumor around the knee. Gait analysis provides a relative objective data about the gait function of patients with prosthesis. The purpose of this study was to compare the gait pattern of the patients who underwent limb salvage surgery with prosthesis for distal femur and that of patients with prosthesis for proximal tibia. This study included ten patients (4 males, 6 females, mean age 22.7 years, range 14-36) who underwent a wide resection and Kotz hinged modular reconstruction prosthesis replacement and six normal adult(Control). The site of bone tumor was the distal femur (Group 1) in six patients and proximal tibia (Group 2) in 4 patients. The follow-up period ranged from 15 to 82 months (mean : 33 months). The evaluation consisted of clinical assessment, radiographic assessment, gait analysis using VICON 370 Motion Analysis System. The gait analysis included the linear parameters such as, walking velocity, cadence, step length, stride length, stance time, swing time, single support and double support time and the three-dimensional kinematics (joint rotation angle, velocity of joint rotation) of ankle, knee, hip and pelvis in sagittal, coronal and transverse plane. For the kinetic evaluation, the moment of force (unit: Nm/kg) and power (unit: Watt/kg) of ankle, knee and hip joint in sagittal, coronal and transverse plane. In the linear parameters, cadence, velocity, step time and single support were decreased in both group 1 and group 2 compared with control. Double support decreased in group 2 compared with control significantly(p<.05). In contrast to our hypothesis, there was no significant difference between group 1 and group 2. In Kinematics, we observed significant difference (p<.05) of decreased knee flexion in loading response (G2

• Korean Journal of Applied Biomechanics
• /
• v.29 no.2
• /
• pp.121-128
• /
• 2019

Objective: The aim of this study was to examine the relation between swing phase and airborne phase of Tkatchev motion which was successfully performed with following motion by excellent middle and high school athletes in horizontal bar. Method: The subjects for this study were 8 male middle and high school top athletes. After their Tkatchev motions were filmed by two digital highspeed camcorders setting in 90 frames/sec at the 44th National Gymnastics against Cities and Provinces, the % lapse time lapse time of each instant, inferred maximum force acting on horizontal bar, and other kinematical variables were calculated through DLT method. After the relations among the % lapse times of each instants of downswing-start, downswing-finish, whipswing-finish, release, peak-height, and lapse time of regrasp, the relation among maximum force acting on bar, % lapse time, peak height, and the relation between % lapse time and release height were examined, the biomechanical timing characteristics of Tkatchev motion were as follows. Results: Firstly, it was revealed that the whole lapse time was $1.62{\pm}.06s$ and the correlation between the % lapse time of downswing-start and % lapse time of release was .819. Secondly, it was revealed that the pattern of COG path was shifted forwardly and tilted 11 clockwise from origin. Thirdly, it was revealed that maximum force acting on bar was inferred in $2,283{\pm}425N$ ($4.7{\pm}.6BW$) and the correlation between maximum force and peak height was r = .893. Lastly, it was revealed that the horizontal and vertical component of body COG velocity was $-2.14{\pm}.29m/s$, $2.70{\pm}.43m/s$ respectively, release height was $.49{\pm}.12m$, and shoulder angle was $139{\pm}5deg$, and that the later the % lapse time of release, the higher the release height (r = .935). Conclusion: It is desired that the gymnastic athletes should delay the downswing-start near the horizontal plane on $2^{nd}$ quadrant because the later the % lapse time of downswing, the higher the release height. After all the higher release height could ensure the athletes to regrasp the bar safely, the athletes should exercise to make downswing-start delay.

• Korean Journal of Applied Biomechanics
• /
• v.16 no.2
• /
• pp.97-108
• /
• 2006

C. H. OH, S. N. CHOI, T. G. NAM, The Kinematic Analysis of the Tennis Flat Serve Motion, Korean Jiurnal of Sports Biomechanics, Vol. 16, No. 2, pp. 97-108, 2006. By the comparison and the analysis of the different factors during the tennis flat serve motion such as the required time per section, the movement displacement of the racket, the velocity of the upper limbs joints, the physical center of gravity, and the angle and the angular velocity of the upper limbs joints between an ace player and a mediocre player, these following results were drawn. First, the experiment result of the total time required per section in a tennis flat serve motion showed that an ace player was faster than a mediocre player by 0.4 seconds. This result suggested that it was required to increase the speed of the racket head by a swift swing to perform an effective flat serve motion. Second, the experiment result of the movement displacement of the racket in the tennis flat serve motion showed that an ace player greatly moved toward the left side on an x-axis. But both an ace and a mediocre player were shown to be at the similar points on a y-axis at the moment of the impact of the racket. An ace player was also shown to be located at a higher position on a z-axis by 0.23m. Third, the velocity of the center of gravity of an ace player was faster in every phase than that of a mediocre player in a tennis flat serve motion. Fourth, the velocity of the upper limb joints of an ace player was faster in every phase than that of a mediocre player in a tennis flat serve motion. Fifth, the experiment result of the speed of the racket head in tennis flat serve motion showed that a mediocre player was faster than an ace player in the first phase, but the latter was faster than the former in the second, third, and the fourth phases. Sixth, at the moment of impact of a tennis flat serve, an ace player had greater flexion of the angle of the wrist joints by an 11.8 degree than a mediocre player. An ace player also had greater extension of the angle of the elbow joint and the shoulder joint respectively by a 5.2 degree and a 1.4 degree with a mediocre player. Seventh, an ace player had greater angular velocity of the upper limb joints and the hip joints than a mediocre player at the moment of the impact of tennis flat serve. Eighth, an ace player was shown to have a greater change of the forward and the backward inclination (or the anterior and posterior inclination) of the upper body