• Journal of the Korean Wood Science and Technology
• /
• v.27 no.2
• /
• pp.38-45
• /
• 1999

This study was to figure out proper Formaldehyde/Urea molar ratio of UF resin with satisfactory bonding strength of plywood and properties of particleboard. The six kinds of UF resins were manufactured with F/U molar ratio 1.0, 1.2, 1.4, 1.6, 1.8, and 2.0. The boards were made of three kinds of raw materials : Veneer, Sliver-Particle and Strand-Particle. Manufacturing condition of plywood : amount of mixing resin was 150g/$m^2$. The fourty secs/mm simple-pressing schedule in the pressure 10kgf/$m^2$ was applied for 480mm${\times}$700mm board at the temperature of $110^{\circ}C$ in a hot press. Manufacturing condition of particleboard : Target density was 0.65g/$cm^2$. The stepwise 9 minutes- multi-pressing schedule in the maximum pressure 40kgf/$cm^2$, the minimum pressure 15kgf/$cm^2$ was applied for $480mm{\times}634mm{\times}12mm$ board at the temperature of $150^{\circ}C$ in a hot press. The results are as follows : I. In bonding strength, plywood which was made by F/U molar ratio 1.2 showed the highest value. Other molar ratio resin also gave the satisfied value of KS standard, 7.5kgf/$cm^2$. 2. In internal bond strength of particleboard, Sliver-Particleboard(SLPB) and Strand-Particleboard(STPB) varied respectively from 5.9kgf/$cm^2$ to 4.8kgf/$cm^2$, from 6.7kgf/$cm^2$ to 5.4kgf/$cm^2$. SLPB with F/U=1.2 and STPB with F/U=1.6 had higher IB value. Also, both SLPB and STPB showed lower IB value in F/U molar ratio 2.0 and 1.0. 3. SLPB and STPB with six kinds of UF resin respectively satisfied bending strength of KS standard 150 Type(130kgf/$cm^2$) and 200 Type(180kgf/$cm^2$). Bending strength data for both of SLPB and STPB showed little or no loss from F/U=1.8 to F/U=1.2. Also, STPB was approximately two times higher than that of SLPB. Therefore, the raw material's shape had more effect on bending strength than the FlU molar ratio. 4. F/U=1.6 and 1.4 showed the lower thickness swelling in SLPB and STPB. All of STPBs satisfied thickness swelling of KS standard, under 12%.

• Journal of the Korean Wood Science and Technology
• /
• v.16 no.2
• /
• pp.1-41
• /
• 1988

For the purpose of utilizing the sawdust having poor combining properties as board raw material and resulting in dimensional instability of board, polypropylene chip (abbreviated below as PP chip) or oriented PP thread was combined with sawdust particle from white meranti(Shorea sp.). The PP chip was prepared from PP thread in length of 0.25, 0.5, 1.0 and 1.5 cm for conventional blending application. Thereafter, the PP chip cut as above was combined with the sawdust particle by 3, 6, 9, 12 and 15% on the weight basis of board. Oriented PP threads were aligned with spacing of 0.5, 1.0 and 1.5cm along transverse direction of board. The physical and mechanical properties on one, two and three layer boards manufactured with the above combining conditions were investigated. The conclusions obtained at this study were summarized as follows: 1. In thickness swelling, all one layer boards combined with PP chips showed lower values than control sawdustboard, and gradually clear decreasing tendendy with the increase of PP chip composition. Two layer board showed higher swelling value than one layer board, but the majority of boards lower values than control sawdustboard. All three layer boards showed lower swelling values than control sawdustboard. 2. In the PP chip and oriented thread combining board, the swelling values of boards combining 0.5cm spacing oriented thread with 1.0 or 1.5cm long PP chip in 12 and 15% by board weight were much lower than the lowest of one or three layer. 3. In specific gravity of 0.51, modulus of rupture of one layer board combined with 3% PP chip showed higher value than control sawdustboard. However, moduli of rupture of the boards with every PP chip composition did not exceed 80kgf/cm2, the low limit value of type 100 board, Korean Industrial Standard KS F 3104 Particleboards. Moduli of rupture of 6%, 1.5cm-long and 3% PP chip combined boards in specific gravity of 0.63 as well as PP chip combined board in specific gravity of 0.72 exceeded 80kgf/$cm^2$ on KS F 3104. Two layer boards combined with every PI' chip composition showed lower values than control sawdustboard and one layer board. Three layer boards combined with.1.5cm long PP chip in 3, 6 and 9% combination level showed higher values than control sawdustboard, and exceeded 80kgf/$cm^2$ on KS F 3104. 4. In modulus of rupture of PP thread oriented sawdustboard, 0.5cm spacing oriented board showed the highest value, and 1.0 and 1.5cm spacing oriented boards lower values than the 0.5cm. However, all PP thread oriented sawdustboards showed higher values than control saw-dustboard. 5. Moduli of rupture in the majority of PP chip and oriented thread combining boards were higher than 80kgf/$cm^2$ on KS F 3104. Moduli of rupture in the boards combining longer PP chip with narrower 0.5cm spacing oriented thread showed high values. In accordance with the spacing increase of oriented thread, moduli of rupture in the PP chip and oriented thread combining boards showed increasing tendency compared with oriented sawdustboard. 6. Moduli of elasticity in one, two and three layer boards were lower than those of control sawdustboard, however, moduli of elasticity of oriented sawdustboards with 0.5, 1.0 and 1.5cm spacing increased 20, 18 and 10% compared with control sawdustboard, respectively. 7. Moduli of elasticity in the majority of PP chip and oriented thread combining boards in 0.5, 1.0 and 1.5cm oriented spacing showed much higher values than control sawdustboard. On the whole, moduli of elasticity in the oriented boards combined with 9% or less combination level and 0.5cm or more length of PP chip showed higher values than oriented sawdustboard. The increasing effect on modulus of elasticity was shown by the PP chip composition in oriented board with narrow spacing. 8. Internal bond strengths of all one layer PP chip combined boards showed lower values than control sawdust board, however, the PP chip combined boards in specific gravity of 0.63 and 0.72 exceeded 1.5kgf/$cm^2$, the low limit value of type 100 board and 3kgf/$cm^2$, type 200 board on KS F 3104, respectively. And also most of all two, three layer-and oriented boards exceeded 3kgf/$cm^2$ on KS F. 9. In general, screw holding strength of one layer board combined with PP chip showed lower value than control sawdustboard, however, that of two or three layer board combined with PP chip did no decreased tendency, and even screw holding strength with the increase of PP chip composition. In the PP chip and oriented PP thread combining boards, most of the boards showed higher values than control sawdustboard in 9% or less PP chip composition.

• Korean Journal of Food Science and Technology
• /
• v.23 no.5
• /
• pp.554-560
• /
• 1991

The physicochemical properties of Korean yam starches (D. aimadoimo, D. batatas and D. japonica) were investigated. The mean granular size of starches were 23.5 μm for D. aimadoimo, 23.9 μm for D. batatas and 18.2 μm for D. japonica. Amylose content, blue value and water binding capacity was $29{\sim}33%,\;0.42{\sim}0.51%\;and\;109.9{\sim}118.3%$, respectively. The optical transmittance of 0.3% (dry basis) yam starch suspensions were increased at $70{\sim}75^{\circ}C$ and D. japonica showed typical two-step transmittance curve. The swelling power and solubility patterns increased over $60^{\circ}C$, and D. aimadoimo was the highest values. Amylogram patterns of 5% (dry basis) yam starch suspensions, determined by Brabender amylograph, were similar to that of yam flours and the viscosity of D. aimadoimo had 630 BU, which was about 5 times higher than 130 BU for D. batatas and D. japonica. Observation under scanning electron microscope lefted marks of resistance to glucoamylase because these surfaces were similar to the natural granules. In rates of solubiliazation by dimethyl sulfoxide, D. aimadoimo showed the highest value. (3-Amylolysis limits of yam starches and their amylose were $71.8%{\sim}75.5%\;and\;90.2{\sim}92.1%$, respectively. Gel filtration patterns of debranched amylopectin by pullulanase were divided into 3 peaks. The weight ratios of peak III to peak II in yam starches were $2.15%{\sim}2.42%$.

• The Korean Journal of Food And Nutrition
• /
• v.29 no.5
• /
• pp.618-627
• /
• 2016

This study evaluated the hydration, gelatinization, and saccharification properties of rice processing for beverage development. The properties of rice were studied on 10 rice cultivars (Samkwang, Ilpum, Seolgaeng, Anda, Dasan-1, Goami-4, Danmi, American rice, Chinese rice, and Thai rice) and employing four kinds of pre-treatment methods (dry grain, wet grain, dry flour, and wet flour). The results showed that moisture content of rice was between 11.88~15.26%. Increase in soaking time along with highest water absorption was noted in American rice cultivar (46.81%). The water binding capacity of Thai rice was higher when compared to that of other rice flours. In addition, solubility and swelling power of rice were 4.52~26.65% and 0.19~2.05%, respectively. The amylose content of Goami-4 was higher in rice processing. Using a rapid visco analyzer (RVA), the initial pasting temperature of Danmi cultivar was found to be the highest; the peak viscosities of Anda cultivar and Dasan-1 cultivar, and Chinese rice were higher than of those of other rice flours. After saccharification, the pH, soluble solids content, and reducing sugar content of rice processed through different pre-treatment methods were in the range of 6.22~7.08, $4.67{\sim}16.07^{\circ}Brix$, and 0.35~11.67% (w/w), respectively. In terms of color values, the L-value of dry grain, a-value of wet (grain, flour), and b-value of dry sample (grain, flour) were found to be the highest. Assessment of various factors and cultivars characteristics of the raw grains are of importance in the development of rice beverage.

• Applied Biological Chemistry
• /
• v.13 no.1
• /
• pp.1-27
• /
• 1970

The process of the forced aging of flue-cured tobacco leaves were studied extensively from various scientific points of view. The Flue-cured tobacco leaves were inoculated and fermented with nicotine resistant Hansenula yeast, or the leaves were subjected under simple forced aging. The above two processes of forced aging were studied from the summarized points of microbiology, physics, chemistry, and biochemistry, and the resulted products ware compared in their physical, chemical and biochemical quality determining factors with that of raw material tobacco leaves (dried-tobacco leaves) and 2 years aged high quality tobacco leaves. The summary results were as follows. 1) The Korean flue-cured tobacco leaves, were forcedly aged under the basic optimum aging condition, temperature $40^{\circ}C$, moisture contents 18%, relative humidity 74%. It was found that this aging condition was the best in bringing the quality of forcedly aged tobacco leaves to the utmost state. 2) Under this optimum temperature and moisture condition of forced aging in about 20 days the forcedly aged tobacco leaves both with yeast inoculation and without yeast inoculation showed the equivalent tobacco qualities comparable with that of more than 2 years aged tobacco leaves. 3) The forcedly aged tobacco leaves both with and without yeast inoculation under $40^{\circ}C$ temperature and $74^{\circ}C$ relative humidity achieved the necessary quality determining physical and chemical changes in about 20 days. 4) The microbial changes during the forced aging were as follows. The population of yeasts and bacteria increased until to 15 days of aging, then decreased thereafter. Whereas the molds grew continously until the end of fermentation. 5) The tobacco quality determing physico-chemico-properties of yeast inoculated aged and simple forcedly aged tobacco leaves, progressed as the follows in time. As the forced aging progresses, swelling and combustibility properties were improved. The pH, total reducing materials, total sugars, alkaloids contents decreased. The contents of organic and ether extractable materials increased. The total nitrogen, protein, crude fiber, ash contents showed no changes. The color properties, excitation purity, luminance, main wave length, showed equivalent changes comparable with that of 2 years aged tobacco leaves. 6) The changes in chemical components in yeast treated and simple forcedly aged tobacco leaves during $15{\sim}20{\;}days$ of forced aging were as follows. The following chemical components decreased as the aging. Sugars-sucrose. rhamnose, glucose. Pigments-chlorophyll, carotenes, xanthophyll and violax anthine. Polyphenols-rutin, chlorogenic and, coffeic acid. Organic acids-iso-butylic, crotonic, caprylic, galacturonic, tartaric, succinic, citric acid. Alkaloids-nicotine, nornicotine. The following components increased as the forced aging progressed. Sugars-frutose, maltose, raffinose. Amino acids-proline, cystine. Organic acids-formic, acetic, propionic, n-butyric, iso-valeric, n-valeric, malic, oxalic, malonic, ${\alpha}-ketoglutaric$, fumaric, glutaric acid. 7) During the forced aging of tobacco Leaves the oxygen-uptake decreased gradually. The enzyme activities of polyphenol oxidase, ${\beta}-amylase$ ${\alpha}-amylase$ decreased gradually. The activities of the enzymes, catalase, and invertase increased once then decreased at the later stage.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.62 no.3
• /
• pp.184-192
• /
• 2017

Rice flours from five rice (Oryza sativa L.) varieties with different amylose content were prepared by both wet and dry milling processes. The moisture content of wet-milled rice flours (WMR) was approximately three-times higher than that of dry-milled rice flours (DMR). Water absorption index (WAI), water solubility index (WSI), and swelling power (SP) increased in proportion to temperature. The WAI, WSI and SP values of DMR were higher than those of WMR. Baeokchal (BOC), which is a waxy rice cultivar, had a significantly high WSI value. Pasting properties of DMR, except for the BOC cultivar, resulted in an increase in peak, trough, final, and setback viscosities. The levels of resistant starch in four cultivars, except for Dodamssal (DDS), were under 1%, irrespective of the milling process, whereas the resistant starch contents of DMR and WMR in DDS were 9.18% and 6.27%, respectively. In vitro digestibility of WMR was higher than that of DMR, and the estimated glycemic index of the rice flour varieties ranged from 57.6 to 81.3. Damaged starch content of WMR was less than that of DMR; in addition, a negative correlation was observed between the amylose and damaged starch contents of WMR. These results suggest that the properties of rice flour vary depending on the milling method and flour variety, and could be a reference for selecting the appropriate processing method.

• Korean journal of food and cookery science
• /
• v.21 no.3 s.87
• /
• pp.301-310
• /
• 2005

The effects of defatted soy flour on the physicochemical characteristics of dough and bread making properties were studied. Defatted soy flour is added to wheat flour for bread-making in order to maximize the use of isoflavones in the soybean. Different particle sizes of both defatted soy flour and wheat flour were prepared by grinding and sievingwith meshes. In the mixograph test, the addition of defatted soy flour to wheat flour increased the requirement for water and decreased the dough development time. Water absorption rates were also investigated to determine the optimum quantity of water for good dough. As the level of defatted soy flour mixed with wheat flour increased, the sedimentation and P.K. values decreased. In comparison with control, the bread made with defatted soy flour especially had a lower specific loaf volume. Specific loaf volume of wheat flour-defatted soy flour bread prepared (Ed- this is an incomplete sentence, it's only a subject clause, and I don't how what you intend to state). In terms of the staling rate and hardness of the wheat flour-defatted soy flour bread, the increased defatted soy flour had a faster staling rate during storage at 5? than at 25? for 5days. From the result of sensory evaluation, wheat flour-defatted soy flour breads containing up to $4\%$ defatted soy flour were rated as being of high quality.

• Journal of Chitin and Chitosan
• /
• v.22 no.2
• /
• pp.110-117
• /
• 2017

This study was conducted to examine the physicochemical properties and hot air-dried and spray-dried powders process of sweet potato and steamed sweet potato. The moisture and the total starch contents were 1.66~2.19% and 52.65~57.42%, respectively. The total starch contents increased during process steaming. The water absorption index of the spray-dried powders (0.97 and 2.03) was lower than that of the hot air-dried powders (2.12 and 4.71), and the water solubility index of the spray-dried powders (83.83 and 86.95%) was higher than that of the hot air-dried powders (68.40 and 81.21%). The particle size and outer topology of the spray-dried powders were 46.18 and $65.53{\mu}m$, and its shape was generally globular. In the DSC analysis of this study, the $T_o$ of the spray-dried powders (64.40 and $67.80^{\circ}C$), $T_p$ of the spray-dried powders (74.40 and $78.20^{\circ}C$), and $T_c$ of the spray-dried powders (81.10 and $81.60^{\circ}C$) was higher than that of the hot air-dried powders. The solubility contents of the spray-dried powders (68.21 and 80.73%) was lower than that of the hot air-dried powders, and the swelling power contents of the spray-dried powders (14.79 and 15.35%) was higher than that of the hot air-dried powders. The amylose contents of spray-dried powders (11.67 and 12.51%) was lower than that of the hot air-dried powders. The soluble dietary fiber contents of spray-dried powders (1.34 and 2.02%) was higher than that of the hot air-dried powders.

• Polymer(Korea)
• /
• v.28 no.1
• /
• pp.24-34
• /
• 2004

Transient sorption experiments were conducted among several combinations of fluoropolymers and various organic solvents. Fully fluorinated polymer tended to exhibit ideal sorption behavior, while partially fluorinated polymers showed anomalous sorption behaviors with a drastic acceleration at the final stage of uptake. Minimization of least-squares of the measured and predicted fractional uptake, which indicated the increasing degree of deviation from Fickian diffusion, gave values of 3.0${\times}$10$\^$-4/, 1.75${\times}$10$\^$-3/, 8.68${\times}$10/sup-3/, 1.75${\times}$10$\^$-2/, respectively, for perfluoroalkoxy copolymer, poly(ethylene-co-tetrafluoroethylene), poly(vinylidene fluoride), poly(ethylene-co-chlorotrifluoroethylene). From stress-strain tests, it was confirmed that non-Fickian diffusion is closely related to the significant variation of mechanical properties (such as modulus and tensile strength) of swollen polymer. Anomalous sorption behavior stemmed from non-Fickian diffusion caused by nonlinear disruption of polar inter-segmental bonds due to solvent-induced plasticization. Thus, it is imperative to investigate the diffusion behavior of swelling solvents in partially fluorinated polymers, especially for the application to barrier materials or perm-selective membranes.

• Journal of Applied Biological Chemistry
• /
• v.55 no.3
• /
• pp.185-189
• /
• 2012

This study was conducted to investigate the effect of different steam condition and dehydration condition on physicochemical characteristics of Olbyeossal made from Waxy rice. All samples were steamed at $95-100^{\circ}C$ for 60 min or at $121^{\circ}C$ for 20 min and then were dehydrated using hot air 45, 60, $80^{\circ}C$ and sun-dried to achieve moisture contents 13-15%. Initial pasting temperature of Olbyeossal was the lower than that of nontreatment sample by parboiling. The combination in steaming $95-100^{\circ}C$ and hot drying at $45-60^{\circ}C$ was showed appropriate pasting properties compared with other condition. The hardness of Olbyeossal was significantly affected by steaming and dehydration condition. The hardness of Olbyeossal showed the higher value for steaming at $121^{\circ}C$ than $95-100^{\circ}C$. The water binding capacity (WBC) and swelling power (SP) were higher steaming at $121^{\circ}C$ than $95-100^{\circ}C$. No significant differences on WBC and SP of Olbyeossal by dehydration condition were observed. As the sensory evaluation results, the combination in steaming at $121^{\circ}C$ and hot-air drying at 45 or $80^{\circ}C$ led to increase preference for appearance, color, taste and overall acceptability. These results indicate that steaming and dehydration condition were affecting factor on physicochemical characteristics of Olbyeossal.