• Progress in Superconductivity
• /
• v.3 no.2
• /
• pp.213-217
• /
• 2002

We have fabricated successfully single-filament composite $MgB_2$/SUS tapes, as an ultrarobust conductor type. The fabrication of the $MgB_2$/SUS tapes was performed by power-in-tube (PIT) process such as swaging and cold rolling. The critical transition temperatures $T_{c}$~38.5 K and ~36 K were observed for the sintered and the nonsintered $MgB_2$/SUS tapes, respectively In addition, the isothermal magnetization M(H) of the sintered $MgB_2$/SUS tapes was measured at temperatures T (between 5 and 50 K) in fields up to 6 T, employing a PPMS-9 (Quantum Design). The persistent current density (J$T_{P}$) values were obtained from the M(H) data, using Bean model, fur the sintered $MgB_2$/SUS tapes. The estimated values were higher than ~ 6$\times$ $10^{5}$ $A/\textrm{cm}^2$ at T = 5 K, with H : 0 G. We also investigated the cross section of the sintered tapes, by using SEM and EDX. An evidence of weak reaction on boundary between $MgB_2$ and SUS tube is found in the SEM and EDX.X.X.X.

• Journal of the Korean Ceramic Society
• /
• v.34 no.1
• /
• pp.70-78
• /
• 1997

3Y-TZP/SUS316 Functionally Graded Material (FGM) was fabricated by slip casting method. Alumina mold was used to overcome problems of gypsum mold in slip casting process, and the optimal dispersion con-ditions of 3Y-TZP/SUS316 binary slurries was determined using electrokinetic sonic amplitude and a viscometer, and observing sedimentation behavior. The properties of the specimens casted by gypsum mold and alumina mold were compared in terms of changes in shrinkage rate, drying and sintering conditions, and microstructure. It was found that the specimens obtaine from the alumina mold showed a clean surface, easier thickness control of each layer, and higher productivity. Especially, no degradation was observed in the SUS316 prepared using alumina mold. Thus it is desirable to use porous alumina mold rather than gyp-sum mold for the slip casting of 3Y-TZP/SUS316-FGM.

• Korean Journal of Materials Research
• /
• v.9 no.2
• /
• pp.211-216
• /
• 1999

Corrosion behavior of austenitic stainless steels of SUS 316L and SUS304L in molten salt of LiCl and $LiCl/Li_2O$ has been investigated in the temperature range of $650~850^{\circ}C$. Corrosion products of SUS316L and 304L in hot molten salt consisted of two layers-an outer layer of Li(CrFe)$O_2$and an inner layer of$Cr_2O_3$. The corrosion layer was uniform in molten salt of LiCl, but the intergranular corrosion occurred in addition to the uniform corrosion in mixed molten salt of LiCl/$Li_2O$. The corrosion rate increased slowly with the increase of temperature up to $750^{\circ}C$, but above $750^{\circ}C$ rapid increase in corrosion rate observed. SUS316L stainless steel showed slower corrosion rate than SUS 304L, exhibiting higher corrosion resistance in the molten salt.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.15 no.4
• /
• pp.243-248
• /
• 2022

The purpose of this paper is to etching SUS MASK by adding an additive (F300) to FeCl3. The equipment used in the experiment is a self-made automatic liquid management system. The automatic liquid management system is a device capable of controlling the Oxidation Reduction Potential (ORP) and specific gravity in real time and supplying FeCl3 and additives in a quantitative manner. SUS MASK was etched in units from 10 sheets up to 200 sheets for 1 minute. It was confirmed that when the initial SUS MASK was 10 sheets, the ORP value started with 628 mV and measured at 611 mV from the time of 40 sheets being injected, and maintained close to 610 mV up to 200 sheets. The specific gravity was maintained near 1.640. And the SUS MASK was measured close to 0.4 mm from 50 sheets to 200 sheets. The experimental conditions of ORP had a specific gravity of 610 mV, 1.463, an etching pressure of 3.0 kg/cm2, an additive (F300) ratio of 1.2%, and the hole size was measured by up to 200 sheets of 10 sheets at once etching. As a result, the diameter approached 0.4 mm from 20 sheets. Even if the number of SUS MASK was increased, the ORP and specific gravity were well controlled, and it was confirmed that the experimental target value was close to 0.4 mm.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2003.10a
• /
• pp.138-139
• /
• 2003

Sandwich sheet samples comprising AA1050/AA1050/AA1050, AA3003/AA1050/AA3003, AA3003 AA3003 AA3003. AA1050/AA3003/AA1050, SUS430/AA3003/SUS430, AA3003/SUS430/AA3003 and SUS430/SUS430/SUS430 were cold rolled in order to clarify the evolution of strain states md textures in the sandwich samples. To investigate the effect of stacking sequences of the samples on strain and texture, the relative contribution of each layer to the total reduction was measured and textures of the mid-layer sheet of sandwich samples were determined.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2003.05a
• /
• pp.136-138
• /
• 2003

Strain states of clad sheets consisted of AL3003 and SUS430 were studied by FEM simulation. Main simulation parameters include roll size, reduction, material properties, material temperature, and friction between roll and material (or friction between materials). To investigate the effect of friction on the evolution of strain states, the friction coefficient between roll and material (or fraction coefficients between materials) was varied. Components of strain rate, strain were compared according to the variation of friction coefficients. And strain states during cladding were compared with those induced by simple rolling process.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.63 no.9
• /
• pp.1180-1185
• /
• 2014

This paper describes the effects on SUS tube of power optical fiber composite cable on underground transmission lines. The effects on grounding, air gap between SUS tube and metal sheath, contact resistance between outer semi-conducting layer and metal sheath and grounding of SUS tube application or not are variously analysed using EMTP in normal operating condition as well as single line to ground fault. From these results, in this paper, the scheme for protecting the electrically abnormal phenomena will be established on power-optical fiber composite cable of underground transmission lines. This paper can contribute to specification of grounding reference of SUS tube of optical fiber composite power cable system.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.11 no.3
• /
• pp.1319-1335
• /
• 2017

This paper proposes an opportunistic reporting-based sensing-reporting-throughput optimization scheme that maximizes the spectral efficiency of secondary users (SUs) in cooperative cognitive radio networks with a soft combining rule. The performance of cooperative spectrum sensing depends on the sensing time, the reporting time of transmitting sensing results, and the fusion scheme. While longer sensing time and reporting time improve the sensing performance, this shortens the allowable data transmission time, which in turn degrades the spectral efficiency of SUs. The proposed scheme adopts an opportunistic reporting scheme to restrain the reporting overhead and it jointly controls the sensing-reporting overhead in order to increase the spectral efficiency of SUs. We show that there is a trade-off between the spectral efficiency of SUs and the overheads of cooperative spectrum sensing. The numerical results demonstrate that the proposed scheme significantly outperforms the conventional sensing-throughput optimization schemes when there are many SUs. Moreover, the numerical results show that the sensing-reporting time should be jointly optimized in order to maximize the spectral efficiency of SUs.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.458-458
• /
• 2012

Fuel Cell is used stacking metal or polymer substrate. This hydro property of substrate surface is very important. Usually, surface property is hydrophilic. The surface oxidation of SUS is investigated through plasma treatments with an atmospheric-pressure dielectric barrier discharge (DBD) for increasing hydrophilic property. The plasma process makes an experiment under various operating conditions of the DBD, which operating conditions are treatment time, plasma gas mixture ratio, the plasma source supply frequency. Two kinds of SUS substrate, SUS-304 and SUS 316L, were used. Discharge frequency has a crucial impact on equipment performance and gas treatment. After the plasma treatment of a SUS plate, highly improved wettability was noted. But, when high oxygen supply, the substrate damaged seriously.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2001.11a
• /
• pp.35-35
• /
• 2001