• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• v.29 no.1
• /
• pp.385-390
• /
• 2005

LMTT (Linear Motor-based Transfer Techn-ology) is a horizontal transfer system for the yard automation, which has been proposed to take the place of AGV (Automated Guided Vehicle) in the maritime container terminal. The system is based on PLMSL (Permanent Magnetic Linear Synchronous Motor) that consists of stator modules on the rail and shuttle car. It is desirable to reduce the weight of LMTT in order to control the electronic devices with minimum energy. In this research, the DACE modeling, known as the one of Kriging interpolation, is introduced to obtain the surrogate approximation model of the structural responses. Then, the GRG(Generalized Reduced Gradient) method built in Excel is adopted to determine the optimum. The objective function is set up as weight. On the contrary, the design variables are considered as transverse, longitudinal and wheel beam's thicknesses, and the constraints are the maximum stresses generated by four loading conditions.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.17 no.2
• /
• pp.152-167
• /
• 2018

The high-speed weigh-in-motion system can collect the traveling speed and load information of individual vehicles, which can be used in a variety of ways for the traffic surveillance. However, it has a limit to apply the high-speed weigh-in-motion data directly to a safety analysis because high-speed weigh-in-motion's raw data are point measured data. In order to overcome this problem, this paper proposes a method to calculate the conflict rate and the Impulse severity based on surrogate safety measures derived from the detection time, detection speed, vehicle length, vehicle type, vehicle weight. It will be possible to analyze and evaluate the risk of rear-end collision on freeway traffic. In addition, this study is expected to be used as a fundamental for identifying crash risks and developing policies to enhance traffic safety on freeways.

• Asia pacific journal of information systems
• /
• v.14 no.1
• /
• pp.101-123
• /
• 2004

User satisfaction has been widely used by information system(IS) researchers as the most appropriate surrogate variable for the systems success since Bailey and Pearson(1983) provided their user satisfaction measurement. Because user satisfaction is a perceived performance measure by users, not a real or objective measure for systems success, however, perceived user satisfaction by users may not be exactly identical with the real systems performance. In this regard, if the user's ultimately perceived satisfaction is different from the real systems performance, we need to investigate why these two measures are different and which factors may cause the difference. From the perspective of disconfirmation of user expecations, this study examined why user satisfaction and real systems performance may not be identical each other. Expectaion-disconfirmation theory which has had a central role in marketing in explaining the effects of expectation and disconfirmation on consumer satisfaction was similarly adopted in this study to explain the role of expectation and disconfirmation in user satisfaction in the IS environment. Based on the expectation-disconfirmation theory, the current study developed a research model to examine the effects of expectation, system performance, and disconfirmation on user satisfaction in particular. Six research hypotheses derived from the research model were empirically tested using the partial least squares(PLS) method. The results of the statistical analysis indicate that the effects of system performance and disconfirmation were fairly strong on user satisfaction, while the user's expectation has shown insignificant influences on user satisfaction.

• Asian Pacific Journal of Cancer Prevention
• /
• v.15 no.24
• /
• pp.10831-10836
• /
• 2015

This study was conducted to establish whether the preoperative platelet to lymphocyte ratio (PLR) is predictive of survival of women with ovarian clear cell carcinoma (OCCC). A PLR > 300 was deemed elevated. Progression-free survival (PFS) was estimated using the Kaplan-Meier method. Cox proportional hazard analysis was used to determine the independent effect of PLR. Thirty-six patients were reviewed. Elevated PLRs were more commonly noted in patients with an advanced vs an early stage of disease (88.9% vs 11.1%). Women with elevated PLR carried a higher rate of disease progression during primary therapy than that those in the normal PLR group (44.4 vs 22.2%). The median PFS for patients with elevated PLR was notably worse than that for patients with normal PLR (10 vs 34 months). Despite the impact of elevated PLR on PFS, it was found to be marginally significant when controlling for commonly applied prognostic markers. It, however, trended toward significance (HR=4.76; 95%CI, 0.95-23.8). In conclusion, an elevated PLR appears to be directly associated with adverse survival rather than being a surrogate for other indicators of a poor prognosis. PLR may be a useful biomarker for predicting survival of women with OCCC and merits further large-scale studies.

• The Journal of Information Systems
• /
• v.12 no.2
• /
• pp.129-149
• /
• 2003

One of the important applications in Enterprise Resource Planning(ERP) systems is the Manufacturing Resource Planning(MRPII) system using Bill of Material(BOM). The manufacturing resource planning determines the quantity and timing of the production or purchase of subassemblies and raw materials needed to support the Master Production Scheduling(MPS). The bill of material is the recipe, a list of the materials needed to make a product. This paper intends to suggest a component-based materials management system using Unified Modeling Language(UML), as an application system for automobile part industry. Applying component based materials management systems designed with UML methodology, we analyzed the workflow and the document on materials management process from production planning to inventory management, and implemented a prototype of efficient materials management system, as a surrogate of existing material requirement planning(MRPI) system. To produce many other assemblies for a automobile part firm, component parts are assembled into subassemblies that are joined to assemble the finished product. Through the system suggested in this study, the level of inventory has cut down and the cost of inventory management has decreased. Also, the development method using UML makes the analysis and design phase to shorten in implementation period of MRPII system. The implementation of materials management system using CBD shows the ease of use in software reuse and the interoperability with corporate Internal information system. The result of applying object-oriented CBD technique is to minimize the risk of life cycle and facilitate the reuse of software as mentioned to limitation of information engineering methodology.

• Korean Journal of Applied Biomechanics
• /
• v.27 no.1
• /
• pp.45-52
• /
• 2017

Objective: The aim of this study was to investigate the periodicity of the lower extremity joint flexion/extension angle to compare the local stability between young and elderly women during walking on a treadmill. Method: Eighteen young women (mean $age=21.2{\pm}1.6y$; mean $mass=57.1{\pm}6.1kg$; mean $height=1.61{\pm}0.04m$) and 18 elderly women (mean $age=66.4{\pm}1.2y$; mean $mass=55.4{\pm}8.3kg$; mean $height=1.56{\pm}0.04m$) participated in this study. Approximate entropy (ApEn) was used to determine the periodicity in the lower limb joint angles. Results: The ApEn values of the two groups were statistically greater in the surrogate data test than in the original time series data (p<.05). The periodicity of the hip and ankle flexion/extension angles decreased in the elderly women group compared with the young women group (p<.05). The periodicity of the lower extremity joint flexion/extension angle showed that the ankle joint increased dominatingly in both groups (p<.05); the hip joint decreased compared with the knee joint in the young women group; and the knee joint decreased compared with the hip joint in the elderly women group (p<.05). Conclusion: These results suggest that the lower extremity joint flexion/extension angles of the young and elderly women during walking contained random noises as well as biological signals. In addition, the differences in the periodicity in the lower extremity joint between the young and elderly women may provide some insight in predicting potential falls and be used as a characteristic indicator for determining local stability in elderly women during walking.

• Nuclear Medicine and Molecular Imaging
• /
• v.43 no.4
• /
• pp.253-258
• /
• 2009

Bone scintigraphy using $^{99m}$Tc-labeled phosphate agents has long been the standard evaluation method for whole skeletal system. However, recent shortage of $^{99m}$Tc supply and advanced positron emission tomography (PET) technology evoked the attention to surrogate radiopharmaceuticals and imaging modalities for bone. Actually, fluorine-18 ($^{18}$F) was the first bone seeking radiotracer before the introduction of $^{99m}$Tc-labeled agents even though its clinical application failed to become pervasive anymore after the rapid spread of Anger type gamma camera systems in early 1970s. However, rapidly developed PET technology made us refocus on the usefulness of $^{18}$F as a PET tracer. Early study comparing $^{18}$F-Na PET scan and planar bone scintigraphy reported that PET has higher sensitivity and specificity in the diagnosis of metastatic bone lesions than planar bone scan. Subsequent reports comparing between PET and both planar and SPECT bone image also revealed better results of PET scan in similar study groups. Rapid clinical application of PET/CT also accumulated considerable amount of experiences in skeletal evaluation and this modality is known to have better diagnostic power than stand alone PET system as well as bone scan. Furthermore $^{18}$F-Na PET/CT revealed better or at least equal results in detection of primary and metastatic bone lesions compared with CT and MRI. Therefore, it is obvious that $^{18}$F-Na PET/CT has potential to become new imaging modality for practical skeletal evaluation so continuous and careful evaluation of this modality and radiopharmaceutical must be required.

• Journal of Pharmaceutical Investigation
• /
• v.37 no.6
• /
• pp.329-338
• /
• 2007

The quality assurance issue of drug products is more important than the general product because it is highly related to the human health and life. In this reason, the regulatory guide lines have continuously been intensified all around the world. In order to achieve effective quality assurance and real-time product release (RTPR) of drug products, process analytical technology (PAT), which can analyze and control a manufacturing process, has been proposed from the United States. With the PAT process, we can obtain significant process features of materials, quality characteristics and product capabilities from a raw material to the final product in the real-time procedure. PAT can also be utilized to process validation using information system that can analyze the risk of drug products through out an entire product life-cycle. In this paper, we first offered a new concept for the off-line process design methods to prepare the improved quality assurance restrictions and a real-time control method by establishing an information system. We also introduced an automatic inspection system by obtaining surrogate variables based on drug product formulations. Finally, we proposed an advanced PAT concept using validation and feedback principles through out the entire life-cycle of drug product manufacturing processes.

• Reproductive and Developmental Biology
• /
• v.33 no.3
• /
• pp.157-162
• /
• 2009

This study was performed to comprehend the developmental characteristics of cloned embryos knocked out (KO) of $\alpha$-1,3-galactosyltransferase (GalT) gene. Immature oocytes were collected and cultured for 40 hrs (1-step) or 20hrs (with hormone) + 20hrs (without hormone) (2-step). The embryos transferred with miniature pig ear fibroblast cell were used as control. The reconstructed embryos were cultured in PZM-3 with 5% $CO_2$ in air at $38.5^{\circ}C$ for 6 days. To determine the quality of the blstocysts, TUNEL and quantitative realtime RT-PCR were performed. The embryos were transferred to a surrogate (Landrace) at an earlier stage of the estrus cycle. The maturation rate was significantly higher in 2-step method than that of 1-step (p<0.05). The blastocyst development of GalT KO embryos was significantly lower than that of normal cloned embryos (p<0.05). The total and apoptotic cell number of GalT KO blastocysts was not different statistically from control. The relative abundance of Bax-$\alpha$/Bcl-xl ratio was significantly higher in both cloned blastocysts than that of in vivo blastocysts (p<0.05). Taken together, it can be postulated that the lower developmental potential and higher expression of apoptosis related genes in GalT KO SCNT embryos might be a cause of a low efficiency of GalT KO cloned miniature pig production.

• Journal of Aerospace System Engineering
• /
• v.13 no.5
• /
• pp.72-78
• /
• 2019

Inlet hammershock is the critical loads condition for designing the inlet duct structure of a fighter. The sudden flow reduction in engine compressor causes inlet hammershock with high pressure. The traditional method was used to combine extreme conditions (maximum speed, sea level altitude, and cold day) to analyze this compression wave inlet hammershock pressure. However, after the 90s there have been papers that presented the probabilistic approach for the inlet hammershock to achieve the appropriate design pressure. This study shows how to analyze the inlet hammershock pressure by making practical use of the Republic of Korea Air Force real flight usage data under probabilistic approach and then analyze approximately 30% decreased inlet hammershock pressure compared with the traditional valve.