• Journal of Forest and Environmental Science
• /
• v.18 no.1
• /
• pp.97-105
• /
• 2001

The main objective of this study was to investigate effects of pigment mixed with different ratio on the double coated paper. Mineral pigments such as clay and ground calcium carbonate(GCC) as well as hollow sphere plastic pigment were used to evaluate the physical, optical properties and printabilities of double coated paper. The physical properties such as gloss and smoothness, and the printability(ink gloss) of double coated paper were measured to evaluate the effects of the bottom layer on improving the properties of top layer. The data indicated that the usage of hollow sphere plastic pigment for the bottom layer coating improved the surface properties of double coated paper, and that ink gloss was significantly influenced by the structure of bottom layer even when hollow sphere plastic pigment was used for the bottom layer coating.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.47 no.4
• /
• pp.5-12
• /
• 2015

In recent years, it had focused on the improvement of paper properties by addition of NFC (Nano-fibrillated Cellulose). Although the addition of NFC to wet-end of papermaking process could be suggested as a new solution to improve the strength properties of paper, it was not possible to avoid the bad drainage caused by the added NFC's chocking pores of wet web. Instead of the direct addition to wet-end, spraying of NFC to web in wire-section was tried in this study and evaluated by checking various paper properties including surface smoothness, tensile strength, folding endurance and stiffness. According to the increase of spraying amount of NFC, above mentioned paper properties were enhanced without excessive deterioration of drainage. Compared with direct introduction to wet-end, spraying could be regarded as a more proper method to enhance the surface smoothness and strength properties of paper.

• Fashion & Textile Research Journal
• /
• v.16 no.1
• /
• pp.153-159
• /
• 2014

This study evaluates the changes of the subjective hand, preference, comfort and mechanical properties of tricot based artificial suede made from sea-island type micro fibers according to raising condition. The subjective hand and the preference of raised suede for jacket were rated by the 20's and 30's women experts according to raising cycles. Comfort properties were evaluated by air permeability, water vapor transmission, and thermal transmission. Mechanical properties were measured by the KES-FB system. The subjective hand of artificial suede was categorized into three hand factors: smoothness, warmness and thickness. Smoothness, warmness and thickness perception increased with raising cycles which affected hand preference and luxuriousness perception. The thickness and wale density of suede increased with the number of raising. Suede became more compact and less pliable and less stretchable due to increased fabric thickness; in addition, the surface of suede became smoother and compressive since the surface evenness of suede improved with smaller fiber fineness and an increased amount of naps covered the base fabric. Furthermore, water vapor transmission decreased and thermal insulation increased. The best raising conditions for artificial suede was four cycles in which artificial suede was preferred without changes in physical properties.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.54 no.4
• /
• pp.154-160
• /
• 2005

We have investigated thermal properties showed by changing the content of carbon black which is the component parts of semiconductive shield in underground power transmission cable. Specimens were made of sheet with the nine of those for measurement. Density of specimens was measured by density meter, and then stress-strain of specimens was measured by TENSOMETER 2000. A speed of measurement was 200[mm/min], ranges of stress and strain were 400(Kgf/$cm^2$) and 600[$\%$]. In addition, tests of stress-strain were progressed by aging specimens at air oven. Finally surface profile was shown in order to looking for protrusion of specimens by using smoothness tester. Density was highly measured according to increasing the content of carbon black from this experimental result, and stress was decreased, while strain was increased according to increasing the content of carbon black. And stress-strain were decreased some after aging because of oxidation reaction of chemical defect. Lastly surface of specimens smoothed generally.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.32 no.4
• /
• pp.41-48
• /
• 2000

The main objective of this study was to investigate the packing state and optical properties of coated paper prepared with different coating colors by varying the blending ratio of such pigment as clay, $CaCO_3$, and plastic pigment. To evaluate the effect of packing state of pigment on the properties of coated paper, the coating thickness, which was theoretically calculated by specific gravity, and packing volume of pigment were used. It was found that there exists close relationship between the coating thickness and surface property of coated paper. For instance, the macro roughness(smoothness) of coated paper is closely related to bulkiness. Plastic pigments used in this research has a high finishing efficiency on the light weight coatings. Especially, hollow sphere pigment was very effective for improving the property of coated paper produced in this test. And when HSP was blended with $CaCO_3$the surface property such as smoothness and gloss improved significantly.

• Journal of the Korean Vacuum Society
• /
• v.11 no.2
• /
• pp.97-102
• /
• 2002

Highly-oriented ZnO thin films has been successfully deposited on Si(100) by metal organic chemical vapor deposition(MOCVD) at $250^{\circ}C$~$400^{\circ}C$ We report on the structural properties of ZnO thin film at various temperatures and at various ratios of the he and $O_2$ gas flow rates. The crystallinity of the thin films was improved and the surface smoothness decreased with the increase of the growth temperature. In x-ray diffraction analysis with respect to ZnO(0002) peak, the full width at half maximum (FWHM) of $0.4^{\circ}$ was achieved at $400^{\circ}C$.

• Korean journal of food and cookery science
• /
• v.25 no.4
• /
• pp.427-434
• /
• 2009

To increase rice consumption and substitute rice flour for wheat flour to make gluten-free bakery products, the physicochemical and pasting properties of rice flours prepared from raw and soaked rices passed through different size screens were investigated. The quality properties of manju dough and preparation of rice manju were also measured. Dry milled flour with soaked rice (DMFSR) were decreased in ash and crude lipid contents compared to dry milled flour with raw rice (DMFRR). Water binding capacity, damaged starch content, and L value of rice flour increased with decreasing particle size, but the b value decreased. Peak, cold, and breakdown viscosities of DMFSR were higher than those of DMFRR by RVA. Hardness of manju dough with DMFSR was lower than that with DMFRR, but that of manju shell exhibited a reverse trend. Sensory difference testing revealed the smoothness of surface, hardness, roughness, and overall quality were significantly different (p<0.05). The smoothness of the surface of manju with DMFRR-200 and all DMFSR were better than that of manju prepared with wheat flour. Hardness showed lower values in DMFRR-200, and all DMFSR as well as wheat flour and roughness decreased with decreasing particle size. Rice manju with wheat flour, DMFRR-200, DMFSR-120, and DMFSR-170 ranked above 5 points and were not significantly different (p<0.05).

• 제어로봇시스템학회:학술대회논문집
• /
• 1987.10b
• /
• pp.249-254
• /
• 1987

This paper presents a new method for generating smooth free-form surface by local correction. B-spline surface is used for its convenience of local correction, and the direction of surface correction is fixed to the average-surface-normal direction. The surface to be corrected is approximated into a uniform cubic B-spline surface. Then, the smoothness (curvature arrows, iso-parametric lines) of the approximated surface is displayed with B-spline control points. When a control point near the region that needs correction is selected, a new point 1 mm higher than the original control point in the direction of the average surface normal is displayed. And the surface is corrected by giving the amount of control point movement interactively. Since the direction of correction is given by the program and the amount of correction is selected by the user, the method is called semiautomatic. sufficiently smooth surface can be obtained by this method. Examples are given to illustrate the method.

• Korean Journal of Computational Design and Engineering
• /
• v.3 no.2
• /
• pp.87-102
• /
• 1998

Given a sequence of cross-sectional curves, the skinning method generates a freeform surface that interpolates the given curves in that sequence. This thesis presents a construction method of a B-spline skinning surface that is fair and satisfies volume constraints. The fairness metric is based on the parametric energy functional of a surface. The degrees of freedom in surface control are closely related lo control points in the skinning direction. The algorithm fur finding a skinning surface consists of two step. In the first step, an initial fair surface is generated without volume constraints and one coordinate of each control point is fixed. In the second step, a final surface that meets all constraints is constucted by rearranging the other coordinates of each control point that defines the initial surface A variational Lagrange optimization method produces a system of nonlinear equations, which can be solved numerically. Moreover, the reparametrization of given sectional curves is important for the construction of a reasonable skinning surface. This thesis also presents an intuitive metric for reparametrization and gives some examples that are optimized with respect to that metric.

• The Journal of Korean Academy of Prosthodontics
• /
• v.34 no.2
• /
• pp.246-265
• /
• 1996

After adjusting glazed surface of laminate veneer porcelain by reduction in the clinical procedure, an additional polishing procedure is required to smoothen the roughened surface by reduction, as it is difficult to glaze it again in the furnace. In this study, four kinds of laminate veneer porcelain were ground with diamond points as done in the clinical procedure. The adjusted porcelain surface was polished with Durawhite stone, Ceramiste points, Exa cerapol, Porcelain polishing wheel, Diamond polishing paste. The degree of surface roughness was evaluated with SEM and profilometer at each step, The self glazed surface and the glazed surface with glazing powder were compared with the polished surface and surface roughness of four kinds of laminate veneer porcelain according to the polishing method and step were obserbed. The following results were obtained : 1. There was no difference in the average surface roughness Ra value and the surface roughness obserbed under SEM according to the polishing methods and steps used, among the four kinds of laminate veneer porcelain including Colorlogic, Exelco, Vintage, and Vitadur alpha product. 2. Due to porosities, the surface in the course of polishing by polishing instruments was rougher than the glazed surface, evaluated with a SEM. 3. Insta-Glaze diamond polishing paste has no statistical difference with self glazed group 1, although it has a lower value in average surface roughness Ra value. 4. Group 2 which was glazed with galzing powder was lowest in view of SEM, but it revealed higher surface roughness Ra value than group 1, the glazed surface and group 8, polished by diamond polishing paste, due to surface waveness. 5. Proper surface smoothness could not be in the surface roughness analysis of SEM and profilometer by Shofu laminate polishing kit composed of Diamond point, Durawhite stone and Ceramiste points. Based on the results of this study, the following conclusions can be drawn. We obtain low surface roughness than glazed surface by polishing instruments, but not perfect results clinically. In order to obtain a perfect clinical result or a surface smoothness comparable to glazed porcelain there is a need for further improvement of porcelain materials, condensa-tion techniques, polishing instruments and polishing methods. Furthermore card should be taken not to breakdown the glazed surface during the clinical and laboratory procedure.