• Journal of Conservation Science
• /
• v.32 no.4
• /
• pp.449-457
• /
• 2016

A stoneware bottle was recovered from the Incheon Yeongheungdo Shipwreck in 2013. Primary observations showed that this object had a sealed opening and was covered with a foreign material. After it was cleaned via mechanical and chemical methods, wave patterns were observed on the outer surface of the bottle and a yellowish-brown transparent material was found within. In this paper, the process of conserving the stoneware bottle and the analysis conducted on the unknown material found within is explained. The conservation process included steps such as cleaning, desalination and restoration. After of the missing area located at the rim, the original shape of the bottle was made clear. In addition, the unknown inner material was analyzed using FT-IR and GC-MS. Results showed that the material is similar to golden lacquer. It is speculated that the Yeongheungdo Ship had wrecked during the Unified Silla period while carrying a bottle loaded with golden lacquer.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.10 no.3
• /
• pp.173-177
• /
• 1977

Optical properties were studied in the Japan Sea based on the optical observations in nine oceanographic stations from September 28 to October 2, 1976. Submarine light intensity was measured by using a submarine illuminometer (RIGO, Type: 2501-A) : equipped with a filter(RIGO, Type:V-R-60, wavelength: 600-620nm). In the upper 40 m depth layer light intensity was measured at 1 m depth interval. The absorption coefficient for red color in the area ranged from 0.142 to 0.323 (mean 0.232) : the Secchi-disc depth in the area ranged from 15 to 23 meters (mean 19.8 meters). The relation ship between absorption coefficient (m) am transparency depth (D) was m =4.93/D. The rates of light penetration for red color at three different depths are computed with reference to the surface light intensity At tile depths of 5 m, 10 m and 20 m, the rates of light penetration were $23.11\%(15-34.2\%),\;6.49\%(3.04-12\%)\;and\;0.698\%(0.113-1.27\%)$ respectively.

• Journal of Advanced Marine Engineering and Technology
• /
• v.37 no.5
• /
• pp.484-492
• /
• 2013

With the industrial acceleration in a lot of countries of the world, the demand for anti-corrosion and anti-abrasion material increases continuously. Particularly, stainless steel with the fine surface and excellent corrosion resistance is widely used in various industrial fields including ship, offshore structures tidal power plant, and etc. In marine environment, however, it is easy to generate by the corrosion damage by $Cl^-$ ion and cavitation damage due to high rotation speed on stainless steel. Therefore, in this research, the cavitation erosion-corrosion test (Hybrid test) was performed for 304 stainless steel specimen used in the high flow rate seawater environment. And the cavitation damage behavior in the corrosive environment was analyzed overall. The high hardness was shown due to the formation of compressive residual stress by the water cavitation peening effect in cavitation condition. However, high current density in the potentiodynamic polarization experiment presented with the breakdown of the passive film caused by physical impact. Therefore, both electrochemical characteristics and mechanical properties must be taken into account to improve the cavitation resistance in seawater.

• Corrosion Science and Technology
• /
• v.9 no.6
• /
• pp.331-337
• /
• 2010

This study compared the macro and micro electrochemical characteristics at the local area of welding metal on dissimilar welding parts for type 304 stainless steel (SS) and type 316L SS. The materials are used for double wall gas pipe of duel fuel engine for a ship. The various potentiodynamic experiments were performed several times in 10% ${H_2C_2O_2}{\cdot}{H_2O}$ solution using macro and micro methods, respectively. The micro electrochemical experiments conducted to resolve at local area on cross-section of dissimilar welding materials by micro-droplet cell device. The micro-droplet cell techniques can be used almost electrochemical experiments to resolve corrosion characteristics of the limited electrode area of the metallic surface between wetted spot of working electrode and tip of sharpened capillary tube. The results of macro electrochemical experiments show that resistance of active dissolution reaction at welding zone was high due to low current density by formation of passivation protection film at passive region. According to the micro electrochemical experiment, the corrosion current density of welding zone and bond zone were relatively high.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.13 no.4
• /
• pp.845-850
• /
• 2018

In this paper, we propose a method to estimate the number of biofouling attached to the surface of marine structures. This method estimates the number of biofouling by calculating the region maxima using images taken in underwater. To do this, we analyze the correlation between the region maxima and the number of biofouling. The analysis showed that there is a significant correlation between the number of region maxima and the number of biofouling. By using the results of this analysis, the experiments were conducted on images taken in the underwater. Experimental results show that the higher the region maxima of the image, is greater than the number of biofouling in the image. The proposed method can be used as an important technology in computer vision for underwater images.

• Journal of Navigation and Port Research
• /
• v.26 no.2
• /
• pp.221-226
• /
• 2002

To provide reliable data for drift prediction models, field experiments were carried out in the coastal region off Busan port. Four different size of vessels(10, 30, 50, 90G/T ton) were deployed for the experiment. Among them G/T 50ton class vessel was equipped with instruments measuring the currents, winds, headings and trajectory data. In the rest of vessels only the position data were recorded for the purpose of target divergence study. The trajectories of each vessel were measured by DGPS(Differential Global Positioning System) and collected by APRS(Automatic Position Reporting System). The experiment was done in wind of 2~10m/s and current of 0.5~1.5m/s. The leeway was derived by subtracting surface current velocity from target drifting velocity. The leeway rate of G/T 50ton vessel was found to be about 3.6% and the computed leeway speed equation was $U_L$=0.042 W - 0.034. The processed leeway angle data were deflected by $-30^{\circ}$~$40^{\circ}$ from the direction of ship drift.

• Journal of Navigation and Port Research
• /
• v.31 no.10
• /
• pp.813-818
• /
• 2007

There are the C.W.C and Towing Tank to the model-test equipments of the boat. A model testing of the high speed boat have a difficult in the performance verification because of very a small the scale-ratio of the ship-model and restricted by flow-velocity of the C.W.C and X-carriage velocity of the T.T. In general, the stepped hull boat is a high of fuel-efficiency because of the resistance reduction by a small wetted surface-area in correspond without stepped-hull boat. But It have a tendency to be bad the rolling performance by reduced stern wetted-area In this paper, the high speed stepped planning-boats with & without attached a stern body were performed to compare the effect of resistance and rolling performance by using sea model-test method.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.17 no.2
• /
• pp.223-234
• /
• 2014

This paper proposes a flexible and highly reusable modeling methodology for a next-generation combat entity which enables joint analysis of performance/engagement effectiveness. According to the scope of the proposed work, the paper is divided into two parts; Part 1 focuses on a conceptual model design, whereas Part 2 proposes detailed model specification and implementation. In Part 1, we, first, classify the combat entity model as combat logic and battlefield function sub-models for joint analysis. Based on the sub-models, we propose two dimensional model partition method, which creates six groups of a single combat entity model by two dimensions: three-activity and two-abstraction. This grouping enables us to reconfigure the combat entity model by sharing the same interface within the group, and the same interface becomes the fundamental basis of the flexible model composition. Furthermore, the proposed method provides a model structure that effectively reflects the real world and maximizes the multi-level reusability of a combat entity model. As a case study, we construct a model design for anti-surface ship warfare. The case study proves enhancement of model reusability in the process of scenario expansion from pattern running to wire guided torpedo operations.

• Bulletin of the Society of Naval Architects of Korea
• /
• v.11 no.1
• /
• pp.9-16
• /
• 1974

To contribute towards more accurate estimation of the virtual inertia coefficient for the horizontal vibration of ships, three dimensional correction factor $J_H$ for the added mass of finitely long elliptic prismatic bars in horizontal vibration in a free surface of an ideal fluid are calculated. In the problem formulation Dr. T. Kumai's quasi-finite length concept[1,11,12] is employed. Now that, in Dr. Kumai's work[1] for the horizontal vibration the mathematical model was a circular cylinder, the principal aim of the authors' work is to investigate the influence of the beam-draft ratio B/T on $J_H$. The numerical results of this work are shown in Fig.3 graphically, from which we may recognize that the influence of B/T on $J_H$ is remarkable as much as that of the length-draft ratio L/T(refer to Fig.1 also). In Fig.3 the curves for B/T=2.00 are of those based on Dr. Kumai's result[1]. On the other hand, the experimental data obtained by Burril et al.[9] for the horizontal vibration of finitely long prismatic bars of various cross-section shapes are compared with the theoretical added mass coefficients defined by combination of the authors' $J_H$ from Fig.3 and two dimensional coefficients $C_H$ obtained by Lewis form approximation for the corresponding sections. They are in reasonable correspondence with each other as shown in Fig.2. Finally, considering that the longitudinal profile of full-form ship's hull is well resembled to that of an elliptic cylinder and that the influences of other factors such as the sectional area coefficient and the shape of section contour itself can be well merged in the two dimensional added mass coefficient, the authors recommend that the data given in Fig.3 may be successfully adopted for the three dimensional correction factor the added mass in the horizontal vibration of hull-form ships.

• Journal of the Society of Naval Architects of Korea
• /
• v.47 no.5
• /
• pp.647-655
• /
• 2010

In this paper, a numerical study is carried out for super-pipe, flat plate and axisymmetric body flows to investigate a validity of using wall function and high $y_1^+$ in calculation of high Reynolds number flow. The velocity profiles in boundary layer agree well with the law of the wall. And it is found that the range of $y^+$��which validated the logarithmic law of the wall grows with increasing Reynolds number. From the result, an equation is suggested that can be used to estimate a maximum $y^+$ value of validity of the log law. And the slope(1/$\kappa$) of the log region of the numerical result is larger than that of experimental data. On the other hand, as $y_1^+$ is increasing, both the friction and the pressure resistances tend to increase finely. When using $y_1^+$ value beyond the range of log law, the surface shear stress shows a significant error and the pressure resistance increases rapidly. However, when using $y_1^+$ value in the range, the computational result is reasonable. From this study, the use of the wall function with high value of $y_1^+$ can be justified for a full scale Reynolds number ship flow.