• Korean Journal of Agricultural Science
• /
• v.45 no.2
• /
• pp.265-282
• /
• 2018

The purpose of this research was to produce symmetric (Saturated-Unsaturated-Saturated, SUS) triacylglycerol (TAG) using palm stearin fraction oil (PSFO) and high oleic sunflower oil (HOSO) as substrates to replace cocoa butter. PSFO was blended with HOSO (1 : 2 weight ratio), and $lipozyme^{(R)}$ TLIM (20 weight % of the substrate) was added. Interesterification was carried out in a shaking water bath at $55^{\circ}C$ at 220 rpm for 6 hours. The response surface methodology (RSM) through the central composite face design was employed to observe the optimized SUS-TAG. The independent factors were the reaction temperature ($X_1$: 65, 75 and $85^{\circ}C$), reaction time ($X_2$: 1, 3 and 5 hours) and ratio of TLIM ($X_3$: 10, 15 and 20 weight %). The dependent variables were $Y_1$ = Saturated-Unsaturated-Unsaturated (SUU, area %), $Y_2=SUS$ (area %), $Y_3$ = Saturated-Saturated-Unsaturated (SSU, area %), $Y_4$ = Unsaturated-Unsaturated-Unsaturated (UUU, area %), and $Y_5=sn-2$ unsaturated fatty acid (area %). The optimal conditions from the central composite face design minimized acyl migration while maximizing the presence of unsaturated fatty acid at the sn-2 position (73.43 area %). The optimal conditions were $X_1=65^{\circ}C$, $X_2=1hour$, and $X_3=20weight%$. As a result of the response surface analysis, the lack of fits was found as $Y_1=0.622$, $Y_2=0.438$, $Y_3=0.264$, $Y_4=0.526$, and $Y_5=0.215$, and their $R^2$ were 0.897, 0.944, 0.826, 0.857, and 0.867, respectively.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.13 no.4
• /
• pp.318-325
• /
• 2000

Dynamic behaviors of saturated-fatty acids $C_{16}$, $C_{18}$, $C_{20}$ and 8A5H with azobenzene were measured by displacement current method when the molecules are stimulated by pressure light and heat. When a barrier was compressed I-A, $\pi$-A isotherms of $C_{16}$, $C_{18}$, and $C_{20}$ were similar to each other but the displacement current of $C_{20}$ which has a long alkyl chain was relatively low. 8A5H showed the form of double liquid films and had a reversible reaction when a barrier was compressed and then expanded. When the molecules of 8A5H were stimulated by 365[nm] light the positive currents which were generated by the structural changes from trans to cis were measured. But the negative currents of the structural changes from cis to trans by 450[nm] light were too weak to detect. When the temperature of the water subphase was increased the surface pressures of the monolayers were increased early because of the thermal activations of the molecules and the double liquid films of 8A5H were disappeared above 40[$^{\circ}C$]EX>].

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.418-418
• /
• 2012

We fabricated a new type of hybrid film using molecular layer deposition (MLD). The MLD is a gas phase process analogous to atomic layer deposition (ALD) and also relies on a saturated surface reaction sequentially which results in the formation of a monolayer in each sequence. In the MLD process, polydiacetylene (PDA) layers were grown by repeated sequential surface reactions of titanium tetrachloride and 2,4-hexadiyne-1,6-diol with ultraviolet (UV) polymerization under a substrate temperature of $100^{\circ}C$. Ellipsometry analysis showed a self-limiting surface reaction process and linear growth of the hybrid films. Polymerization of the hybrid films was confirmed by infrared (IR) spectroscopy and UV-Vis spectroscopy. Composition of the films was confirmed by IR spectroscopy and X-ray photoelectron (XP) spectroscopy. The titanium oxide cross-linked polydiacetylene (TiOPDA) hybrid films exhibited good thermal and mechanical stabilities.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.20 no.2
• /
• pp.433-452
• /
• 2018

The shield tunneling method can minimize surface settlements by preventing the deformation of tunnel face and tunnel intrados due to tunnel excavation. For this purpose, it is very important to control the operating conditions of shield TBM. The face pressure and backfill pressure for tail void grouting should be the most important and immediate measure not only to restrain surface settlement, but also to influence the effective stress and pore water pressure around the circumstance of tunnel during excavation. The reaction of the ground to the application of face pressure and backfill pressure relies on the stiffness and permeability of ground. Especially, the reaction of saturated clayey ground formations, which shows the time-dependent deformation, is different from the permeable ground. Hence, in this paper it was investigated how the TBM operating conditions, ground stiffness, and permeability impact on the surface settlement of saturated clayey ground. For this purpose, a series of parametric studies were carried out by means of the stress-pore water pressure coupled FE analysis. The results show that the settlement of soft clayey ground is divided into the immediate settlement and consolidation settlement. Especially, the consolidation settlement depends on the ground stiffness and permeability. In addition, the existence of critical face pressure and backfill pressure was identified. The face pressure and backfill pressure above the critical value may cause an unexpected increase in the ground settlement.

• Bulletin of the Korean Chemical Society
• /
• v.34 no.4
• /
• pp.1035-1038
• /
• 2013

Rolling circle amplification (RCA) of DNA on an aligned-carbon nanotube (a-CNT) surface was electrically interfaced by the a-CNT based filed effect transistor (FET). Since the electric conductance of the a-CNT will be dependent upon its local electric environment, the electric conductance of the FET is expected to give a very distinctive signature of the surface reaction along with this isothermal DNA amplification of the RCA. The a-CNT was initially grown on the quartz wafer with the patterned catalyst by chemical vapor deposition and transferred onto a flexible substrate after the formation of electrodes. After immobilization of a primer DNA, the rolling circle amplification was induced on chip with the a-CNT based FET device. The electric conductance showed a quite rapid increase at the early stage of the surface reaction and then the rate of increase was attenuated to reach a saturated stage of conductance change. It took about an hour to get the conductance saturation from the start of the conductance change. Atomic force microscopy was used as a complementary tool to support the successful amplification of DNA on the device surface. We hope that our results contribute to the efforts in the realization of a reliable nanodevice-based measurement of biologically or clinically important molecules.

• Journal of the Korean institute of surface engineering
• /
• v.43 no.4
• /
• pp.205-210
• /
• 2010

The A106 Gr B low carbon steel, which was used in the electric power plants and heavy chemical plants, was welded by multi-pass arc welding. The heat affected zone (HAZ) formed by welding was corroded in acid chloride solution, or in saturated $H_2S$ containing acid chloride solution, or in saturated $H_2S$ containing acid chloride solution under applied current. In this order of corrosion solution, the rate of corrosion increased, because $H_2S$ accelerated the iron dissolution, hydrogen evolution, and the formation of nonprotective FeS, whereas the applied current accelerated the electrochemical reaction. The scales formed in acid chloride solution consisted primarily of $Fe_3O_4$, while those formed in $H_2S$ containing acid chloride solution consisted primarily of $Fe_3O_4$ and FeS.

• Tribology and Lubricants
• /
• v.19 no.1
• /
• pp.1-8
• /
• 2003

Recently, PM-high speed steel(PM-HSS) has reportedly been a good alternative material for rolling mill because of its superior performance to conventional HSS. This paper has been aimed to investigate the possibility for application to rolling contact element for PM-HSS by X-ray diffraction technique. The X-ray elastic constant for PH-HSS has been found by X-ray diffraction during the four-point bending test. Residual stress and half-value breadth on the contact surface during rolling contact fatigue process by X-ray diffraction have also been measured. The result of this study shows that the application of X-ray diffraction technique to PM-HSS could be as possible alternative material as conventional HSS. Half-value breadth on rolling contact surface by X-ray diffraction is not changed during rolling contact fatigue process. On the other hand, the residual stress is changed. This suggests that dislocation reaction has been hardly occurred in rolling contact, depending on super-saturated carbon in PM-HSS.

• Journal of the Korean institute of surface engineering
• /
• v.12 no.3
• /
• pp.161-166
• /
• 1979

Theoretical and practical aspects are investigated for electrochemical behavious, plating processes and the structures of electrodeposit of Pb-Sn binary alloy plating through numerous literatures in this report. The anodic and cathodic electrode reaction mechanisms of Pb and Sn could co-deposit and make Pb-Sn alloy deposit from the results of cathode current density-cathode potential curves of Pb, Sn and Pb-Sn alloys in fluoborate solutions. The compositions of the best alloy plating solutions are obtained for the purpose of bearing, anticorrosion and solder plating. In general, the casting anodes of Pb-Sn alloys are used, but separated anodes of Pb and Sn pure metal are used in order to obtain the fine compositions of Pb-Sn alloy deposits. The electrodeposits of Pb-Sn alloy are in nonequilibrium state and saturated solid solutions. Thus, ${\beta}$-phase (Sn-phase) is precipitated by heat treatment. The texture and structure of the electrodeposit are associated with the surface energies of deposit lattice planes and with the cathode polarization. The electrodeposit of Pb-Sn alloy is shown as lamellar structure.

• Journal of Microbiology and Biotechnology
• /
• v.9 no.2
• /
• pp.127-131
• /
• 1999

Anaerobically grown cells of an Fe(III)-reducing bacterium, Shewanella putrefaciens IR-l, were electrochemically active with an apparent reduction potential of about 0.15 V against a saturated calomel electrode in the cyclic voltammetry. The bacterium did not grow fermentatively on lactate, but grew in an anode compartment of a three-electrode electrochemical cell using lactate as an electron donor and the electrode as the electron acceptor. This property was shared by a large number of Fe(III)-reducing bacterial isolates. This is the first observation of a direct electrochemical reaction by an intact bacterial cell, which is believed to be possible due to the electron carrier(s) located at the cell surface involved in the reduction of the natural water insoluble electron acceptor, Fe(III).

• Proceedings of the Korean Society of Soil and Groundwater Environment Conference
• /
• 2001.09a
• /
• pp.51-54
• /
• 2001

This research was carried out to evaluate feasibility of using an Electrokinetic-Fenton(EK-Fenton) technique to treat hydrophobic organic pollutant(phenanthrene) from soils. Experiment examined the effect by introducing a continuous flow of a 3.5% hydrogen peroxide solution at the anode. An electric gradient of 1V/cm was applied to enhance the saturated flow in the soil cell for a period of 11 days. After 11 days or 1 pore volume, overall concentration of residual phenanthrene in the soil cell was 11% and residual phenanathrene concentration in the soil was found to increase with toward the cathode. This results indicated that Fenton-like reaction catalyzed by mineral surface was effective in oxidizing phenanthrene. This results also showed that hydrogen peroxide was effectively transported into the soil by electroosmotic flow as well as by diffusion.