• Journal of Powder Materials
• /
• v.24 no.2
• /
• pp.102-107
• /
• 2017

Porous polytetrafluoroethylene (PTFE) thin films are fabricated by spin-coating using a dispersion solution containing PTFE powders, and their crystalline properties are investigated after thermal annealing at various temperatures ranging from 300 to $500^{\circ}C$. Before thermal annealing, the film is densely packed and consists of many granular particles 200-300 nm in diameter. However, after thermal annealing, the film contains many voids and fibrous grains on the surface. In addition, the film thickness decreases after thermal annealing owing to evaporation of the surfactant, binder, and solvent composing the PTFE dispersion solution. The film thickness is systematically controlled from 2 to $6.5{\mu}m$ by decreasing the spin speed from 1,500 to 500 rpm. A triboelectric nanogenerator is fabricated by spin-coating PTFE thin films onto polished Cu foils, where they act as an active layer to convert mechanical energy to electrical energy. A triboelectric nanogenerator consisting of a PTFE layer and Al metal foil pair shows typical output characteristics, exhibiting positive and negative peaks during applied strain and relief cycles due to charging and discharging of electrical charge carriers. Further, the voltage and current outputs increase with increasing strain cycle owing to accumulation of electrical charge carriers during charge-discharge.

• Journal of the Korean Society for Heat Treatment
• /
• v.24 no.5
• /
• pp.271-276
• /
• 2011

The effect of grain size on the deformation induced martensite transformation and mechanical properties in austenitic stainless steel with high amount of Mn was studied. a'-martensite was formed by deformation and deformation induced martensite was formed with surface relief. With increase of grain size, volume fraction of deformation induced martensite was increased. With the increase in degree of cold rolling, hardness, and tensile strength was rapidly increased with linear relationship, while, elongation was decreased rapidly and then decreased slowly. With increase of grain size, hardness and tensile strength was rapidly increased with linear relationship, while elongation was decreased rapidly. The hardness, tensile strengths, and elongation were more strongly influenced by deformation induced martensite than the grain size.

• Journal of the Korean Association of Oral and Maxillofacial Surgeons
• /
• v.46 no.5
• /
• pp.321-327
• /
• 2020

Objectives: This study is aimed to evaluate and compare the effect of moist heat fomentation therapy with ultrasound therapy in patients with the masticatory myalgia. Materials and Methods: The study was conducted on 42 patients with masticatory myalgia, dividing them into two groups; Group A (21 patients), received moist heat therapy and Group B (21 patients), received ultrasound therapy for seven effective days. Prior and after the treatment the numeric rating scale (NRS) and the electromyography (EMG) scores were recorded and compared. The observations were analyzed clinically and statistical support was taken to assess the NRS and EMG data. Results: Irrespective of the groups, patients testified a significant reduction in pain after the treatment. From the EMG readings; even though the standard deviation for each group was varied considerably, EMG recorded an improved muscle activity. Statistical analysis was used to assess and identify the best treatment methodology between the two modalities. Conclusion: From the statistical analysis, it is concluded that, though both the therapies had significantly reduced the symptomatic response, it is moist heat fomentation that improved muscle activity both statistically and clinically in comparison to ultrasound.

• Korean Journal of Occupational Health Nursing
• /
• v.24 no.4
• /
• pp.331-339
• /
• 2015

Purpose: The purpose of this study was to investigate the moderating effects of social support between emotional labor and job satisfaction in clinical nurses. Methods: Participants were 311 clinical nurses and data were collected from July 11th to 18th, 2014. The data were analyzed using descriptive statistics, t-test, ANOVA, Pearson correlation coefficient and hierarchical multiple regression with SPSS 21.0. Results: The job satisfaction indicated a significant relationship to surface-acting (r=-.191, p=.001), deep-acting (r=.179, p=.002) and social support (r=.342, p<.001) respectively. Emotional labor significantly affected job satisfaction (F=11.592, p<.001), and explained 5.4% of the variance in job satisfaction. The social support acted as a moderator on the relationship between emotional labor and job satisfaction at significant level (F=11.416, p<.001). Conclusion: The results of this study suggest that it is important to develop social support promoting and stress relief program for clinical nurses to improve job satisfaction.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.25 no.4
• /
• pp.245-252
• /
• 2016

Girth gears are applied in the mining, cement, and mineral processing industries and used in various types of horizontal mills, rotary dryers and kilns, and other heavy-gear ring applications. The large ring gears are normally fitted outside mills or kilns to provide the primary rotational drive. Recently, an external pinwheel gear set (e-PGS) was introduced to overcome manufacturing problems associated with girth gears. e-PGS is also suitable for low-speed, heavy-duty mechanical transmission and dusty and poor-lubrication conditions. This paper first presents a new profile modification of root relief for the e-PGS cam pinion. We then investigate load-stress factors to estimate the surface fatigue life by varying the shape design parameters. The results show that the contact fatigue life of an e-PGS can be extended significantly by increasing the profile shift coefficient. However, support bearing life of the pinwheel depends more on the contact force distribution than the profile shift coefficient.

• Journal of Biosystems Engineering
• /
• v.27 no.2
• /
• pp.79-88
• /
• 2002

This study was conducted to develop system for high speed rice transplanting machines. The control system includes a sensor detecting the tilt angle of the seedling bed, a micro-controller and a hydraulic system consisting of a double acting cylinder, a four-way three-position solenoid valve, a relief valve and a hydraulic pump. The levelling system shared the pump with the existing steering control, resulting in a tandem center circuit for the steering and levelling control systems. Using the input signal from the sensor, the micro-controller determined and generated the output signal to control the cylinder through the solenoid valve to keep the seedling bed always parallel to the water surface regardless of soil unevenness during the transplanting operations. Both an ON/OFF and a PWM control schemes were tested. When the flow rate was more than 1 ι/min in the ON/OFF control, the system showed unstable rolling. However, in the PWM control, the system worked stably although the flow rate was more than 1 ι/min. The PWM control showed a better performance when a large difference between the angle and the dead band of the control system occurred. The characteristics of tile system response to given tilt angles were predicted by a computer simulation. Both the ON/OFF and the PWM control systems worked well providing that the operating and waiting times were properly adjusted.

• Korean Institute of Interior Design Journal
• /
• v.17 no.4
• /
• pp.58-65
• /
• 2008

The purpose of this study is to explore the revealing corporality in Mies' architecture. The character of such technical materials refuses or weakens the physical reality of the wall by the thoughts concerning the unlimited space or continuous space in Modern architecture. The wall or facade revealed visually is substituted to substance without materiality or just disappeared. This causes a problem of perception of architectural form itself in Modern architecture. Leonardo suggested that all kinds of human perception happens within the visibility and touchability. Likewise, the corporality as a visual reality can be perceived as an important and fundamental value, which can measure the real being. In this respect, This study reviews his architectural meaning by tracing the visual reality in his works. Namely, the emphasis of architectural elements through the relief effect, the expression of massiveness through the reflection of the glass wall and the emphasis of the color through the contrast are interpreted in the intention of Mies to emphasize the visual corporality of the building. This study is to reevaluate the meaning of Mies's architecture through understanding of his thought about the architectural corporality, which has been forgotten by the transparency concept of Modern architecture.

• Current Optics and Photonics
• /
• v.4 no.4
• /
• pp.293-301
• /
• 2020

In this paper we propose and theoretically analyze a monolithic multiparametric sensor consisting of a superstructure of surface-relief waveguide Bragg gratings (WBGs), a micro-machined diaphragm, and a cantilever beam. Diaphragms of two different configurations, namely circular and square, are designed and analyzed separately for pressure measurement. The square diaphragm is then selected for further study, since it shows relatively higher sensitivity compared to the circular one, as it incurs more induced stress when any pressure is applied. The cantilever beam with a proof mass is designed to enhance the sensitivity for acceleration measurement. A unique mathematical method using coupled-mode theory and the transfer-matrix method is developed to design and analyze the shift in the Bragg wavelength of the superstructure configuration of the gratings, due to simultaneously applied pressure and acceleration. The effect of temperature on the wavelength shift is compensated by introducing another Bragg grating in the superstructure configuration. The measured sensitivities for pressure and acceleration are found to be 0.21 pm/Pa and 6.49 nm/g respectively.

• Journal of the Korean Society for Heat Treatment
• /
• v.34 no.3
• /
• pp.116-121
• /
• 2021

This study was carried out to investigate the effect of transformation induced martensite on the tensile properties of Fe-20Mn-12Cr-3Ni-3Si alloy. α' and ε-martensite were formed by cold rolling, and these martensite were formed with according to the specific direction, surface relief and partially intersection. With an increasing degree of cold rolling, amount of α'-martensite was slowly increased, whereas amount of ε-martensite was rapidly increased. Volume fraction of ε-martensite formed by cold working was large than α'-martensite. Tensile strength was rapidly increase and elongation was rapidly decreased with an increasing of degree of cold rolling. This means that tensile strengh and elongation was greatly influenced by the volume fraction of ε-martensite formed by cold rolling then α'-martensite.

• Journal of The Geomorphological Association of Korea
• /
• v.24 no.1
• /
• pp.39-50
• /
• 2017

This study was conducted to analyze the variation of hydro-geomorphological environment along Baekgok wetland, which experiencing periodical inundation, in that water-level fluctuation of reservoir caused by irrigation. Since the field data is unavailable, modeling techniques, involving models such as HSPF and TELEMAC-2D, have been applied to simulate hydrological cycle in watershed and hydrodynamics in channel scale. The result of simulation indicates that the water-level of reservoir determines both the water surface extension and water depth in the wetland. Furthermore, it also shows that water-level functions as a spatial limit factor for a fluvial environment and woody vegetation such as willow. The fact of which the scale of water-level fluctuation being larger than an average topographical relief along the wetland can explain the result. While the water-level kept high, the wetland is submerged and waterbody becomes lentic. In contrast, while the water-level is lowered, fluvial phenomena of which being dependent on flow rate and channel shape become active. Hence, the valid fluvial process is likely to take place only for 4 months annually just near the channel, and it advances to a conclusion expecting a deposition to be dominant among the wetland except for such area. It is anticipated that such understanding can contribute to establishing plans to preserve the geomorphological and ecological value of the Baekgok wetland.