• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.30 no.7 s.250
• /
• pp.663-670
• /
• 2006

The presented study aims to investigate the colloidal droplet deposition caused by evaporation of the liquid. In the numerical analysis, the evaporation is carried out by using different evaporation function intended to obtain different shape of solute deposition. In the experiment, the colloidal droplets of different solvents are placed on a glass plate and the surface profiles are measured after drying the solvents of the droplets to investigate the effect of the solvent evaporation on the final deposition profile. Comparing the surface profiles obtained under different conditions, the optimum drying conditions of colloidal droplets are, determined to obtain uniform surface profiles. The numerical results showed that ring-shaped deposition of solute was formed at the edge of the droplet due to the coffee stain effect and the height of the ring was reduced at the lower evaporation rate. The experiments showed that the boiling point of a solvent was critical to the surface uniformity of the deposition profile and the mixture of solvents with different boiling points influenced the uniformity as well.

• Tunnel and Underground Space
• /
• v.12 no.4
• /
• pp.268-276
• /
• 2002

In this study, a 3D coordinate measurement system equipped with a laser displacement meter for digitizing rock joint surface was established and the digitized data were used to calculate several roughness parameters. The parameters used in this study were micro avenge inclination $angle(i_{ave})$, average slope of joint $asperity(SL_{ ave})$, root mean square of $i-angle(i_{rms})$, standard deviation of height(SDH), standard deviation of $i-angle(SD_i)$, roughness profile $index(R_P)$, and fractal dimension(D). The relationships between the roughness parameters based on the digitzation of the surface profile were analyzed. Since the measured value varied according to the degree of reflection and the variation of colors at the measuring point, rock joint surface was painted in white to minimize the influence of the surface conditions. The comparison of the measured values and roughness parameters before and after painting revealed the better consequence from measurement on the painted surfaces. Also, effect of measuring interval was studied. As measured interval was increased, roughness parameters were exponentially decreased. The incremental sequence of degree of decrease was $SDH\; i_{ave},\; i_{rms},\; SD_i,\;and\; R_ p-1$. As a result of comparison of parameters from pin-type measurement system and laser type measurement system, all value of parameters were higher when laser-type measurement system was used, except SDH.

• Journal of the Society of Naval Architects of Korea
• /
• v.46 no.3
• /
• pp.219-231
• /
• 2009

Numerical simulations have been carried out for a 138K LNG Carrier (KLNG) model ship with free surface, using WAVIS 2.0 and Fluent 6.3.26 with various $y^+$ values and different grid densities. Level-set method for free surface capturing was adopted in WAVIS, while VOF has been used in Fluent. The calculated results were compared with the experiment data. Resistance coefficient, wave pattern, wave profile along the hull surface, axial velocity contours and transverse vectors had been analyzed. When the first $y^+$ value was fixed at 60, the simulation results from both WAVIS and Fluent were improved as the number of grids increased. The convergence time of WAVIS was much shorter than that of Fluent. Furthermore, WAVIS predicted the velocity field and the wave profile along the hull surface better than Fluent. However, Fluent gave better wave patterns.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.35 no.3
• /
• pp.237-241
• /
• 1999

It was investigated that the condition of fishing ground gave what kind of effect school type in relation to the property for the target school after the vertical temperature profile and school type were observed when tuna purse seiner for tuna purse seine was operated in the western pacific Ocean around the equator between December 12, 1993 and January 26, 1994. The results are as follows;1. This study divided fish schools associated with drift objects, a one targeted-operation, and the pelagic migrating fish schools that are another one for the property. The total of 23 operations were complected including 6 that targeted fish schools associated with drift objects and 17 that targeted pelagic migrating fish schools. It was known that the main operation was conducted on pelagic migrating fish school.2. Average and standard deviation of the depth of the surface mixing layer was 86.0m and 13.8m for fish schools associated with drift objects. 61.6m and 13.0m for pelagic migrating fish schools, respectively. The average depth of the surface mixing layer of the pelagic migrating fish schools was lower when compared to the fish schools associated with drift objects however the concentration of standard deviation was higher than those fish schools associated with drifted objects. Accordingly, it was assumed that the effect of vertical temperature profile for pelagic migrating fish school was higher than the fish schools associated with drift objects.

• Analytical Science and Technology
• /
• v.10 no.5
• /
• pp.357-361
• /
• 1997

A Griemm type Glow Discharge cell is attached to a commercial quadrapole based ICP-MS and used for the analysis of surface analysis. By employing 2.0mm diameter, mode and proper experimental conditions, several layers of few ${\mu}m$ thickness are analysed within 30 minutes. Multi-layers of Cu-Ni, Fe-Ni are analyzed with the resolution of 10nm by GDMS. Proper experimental conditions make a flat bottom crater shape and good resolution for multi-layer depth profile study.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2009.05a
• /
• pp.295-298
• /
• 2009

Bent ducts add loss and decrease efficiency. Many researchers have been conducted the performances of bent ducts, but their shapes of inlet and outlet are same. However, in this investigation, the focus is on a bent duct which is annular at the inlet and circular at the outlet. The bent duct of these complex shapes has not been investigated, but has been used in many fields. The performance of such bent duct is investigated under inlet speed 54 m/s and Re = 238,000. Wall static pressure tappings are located surface of the bent duct to measure the static pressure and a probe is traversed at the inlet and outlet of the bent duct to measure the total pressure. As a result, it presents static pressure distribution on the bent duct surface, streamwise velocity profile at inlet and outlet of the bent duct and total pressure loss profile at outlet. In this investigation, the total pressure loss coefficient is 0.243.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.15 no.4
• /
• pp.101-108
• /
• 2016

Endmill fillet cutting at the corner was conducted with the online measurement of cutting forces and tool deflection by a tool dynamometer and an eddy current sensor system. The profile of the machined surface was also compared with the CAD profile with a Coordinate Measuring Machine (CMM) and CALYPSO software. It was found that the end mill cutter with four blades has a better surface profile than that with two blades, and the cutting forces and tool deformation were increased as the cutting speed was increased. When the tool located at the degree $45^{\circ}$ corner was found to conduct the maximum cutting force than started to the point of the workpiece. As it was compared with the CMM and ANOVA analysis result in the case that the cutting force and tool deformation was the maximum, it was found that the result was affected by the spindle speed and the number of blades.

• Journal of Surface Science and Engineering
• /
• v.27 no.3
• /
• pp.158-165
• /
• 1994

Cu-Cr alloy thin film requires good quality of etching be used for TAB technology. The etched cross sec-tion was clean enough when the etching was performed in 0.1M $FeCl_3$ solution at $50^{\circ}C$. The etching rate was increased with the amount of $KMnO_4$. For enhanced profile of cross section and rate, the spray etchning was found to be superior compared to the immersion etching. A series of experiments were performed to improve the uniformity of the current distribution in electrodeposition onto the substrate with lithographic patterns. Copper was electrodeposited from quiescent-solution, paddle-agitated-solution, and air-bubbled-solution to in-vestigate the effect of the fluid flow. The thickness profile of the specimen measured by profilmetry has the non uniformity at feature scale in quiescent-solution, because of the longitudinal vortex roll caused by the natural convection. However, uniform thickness profile was achieved in paddle-agitated or air bubbled solu-tion.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.4 no.4
• /
• pp.219-224
• /
• 1992

A numerical method using the truncated Fourier series is presented to predict the wave potential and water surface profile for two dimensional nonlinear standing waves. The unknown coefficients of the series are to be determined through the Newton solution of nonlinear simultaneous equations given by the governing equation and boundary conditions of the problem. In order to prove the effectiveness of the present method. an existing Stokes-like perturbation method is considered together, and a hydraulic experiment for measuring water surface profile and wave pressure is performed as well. The results are such that the present method can generally give exact solutions even for relatively big wave stiffness regardless of the water depth condition. It also demonstrates its validity by showing double humps in the crest of temporal wave pressure profile which normally appear in strongly nonlinear standing waves.

• Proceedings of the KIEE Conference
• /
• 2002.11a
• /
• pp.245-247
• /
• 2002

The paper represents the effects of the drive-in process parameters on the residual stress profile of the p+ silicon film. For the quantitative determination of the residual stress profiles, the test samples are doped via the fixed boron diffusion process and four types of the thermal oxidation processes and consecutively etched by the improved process. The residual stress measurement structures with the different thickness are simultaneously fabricated on the same silicon wafer. Since the residual stress profile is not uniform along the direction normal to the surface, the residual stress is assumed to be a polynomial function of the depth. All of the coefficients of the polynomial are determined from the deflections of cantilevers and the displacement of a rotating beam structure. As the drive-in temperature or the drive-in time increases, the boron concentration decreases and the magnitude of the average residual tensile stress decreases. Also, near the surface of the p+ film the residual tensile stress is transformed into the residual compressive stress and its magnitude increases.