• 한국안전학회지
• /
• 제31권1호
• /
• pp.66-73
• /
• 2016

Lyocell fibers were used as a precursor in order to improve yield and strength of cellulose-based precursor while manufacturing activated carbon fiber(ACF). Lyocell fibers as a precursor for the preparation of ACF were surface-modified by reaction with 3-aminopropyltriethoxysilane(APTES) and pre-treated with KOH and H3PO4. Using aforementioned precursor, ACFs were prepared by a series of stabilization, carbonization and activation process at high temperatures. On each process, FT-IR, TGA, UTM and SEM were used to observe fibers' physical properties including structure and porous surfaces. FT-IR results proved that surface modification was achieved during stabilization, carbonization and activation process. TGA results during carbonization process found that surface modified fibers with APTES 0.02 mol(A2) showed higher thermostability, and extended pre-treatment increased yield. Especially, yield was found to have an increase of 10~20 wt% with surface modification during activation process. UTM results showed that tensile strength has the same order of concentration of APTES after surface modification, however, was found to show lower tensile strength than lyocell fibers after stabilization process. SEM results revealed that more homogeneous porosity control could be proceed after modifying the surface for the effective removal of hazardous substances.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 1995년도 춘계학술대회 논문집
• /
• pp.1-8
• /
• 1995

This paper proposed a simple method for measuring surface roughness of ground surface. utilizing non-contact in-process measuring system using the diode laser. The measurement system is consisted of a laser unit with a diode laser and a cylindrical lens a detecting unit with polygon mirror and CCD array sensor. and a signal processing unit with a computer and device. During operation, this measuring system can provide information on surface roughness in the measuring distance with a single sampling and simultanilusly monitor the state of the grind wheel. The experimental results, showed that the increase of the feed rate and the dressing speed an caused increase in the surface roughness and when the surface roughness is 4Rmax-10Rmax, the cutting speed is 1653m/min-1665m/min. the feed rate is 0.2m/min-0.9m/min, the dressing speed is 0.2mm/rev-0.4mm/rev, the stylus method and the in-process method can be obtained the same results. thus under limited working conditions. using the proposed system. the surface roughness of the ground surface during cylindrical grinding can be obtained through the in-process measurement method using the diode laser.

• 한국표면공학회지
• /
• 제39권6호
• /
• pp.268-275
• /
• 2006

In this study, effect of sputtering on the plasma-nitriding substrate and before PVD coating on the microstucture, microhardness, surface roughness and the adhesion strength of CrZrN thin films were investigated. Experimental results showed that this sputtering process not only removed surface compound layer which formed during a plasma nitriding process but also induced an alteration of the surface of plasma nitrided substrate in terms of microhardness distribution, surface roughness. This in turn affected the adhesion strength of PVD coatings. After sputtering, microhardness distribution showed general decrease and the surface roughness became increased slightly. The critical shear stress measured from the scratch test on the CrZrN coatings showed an approximately 1.4 times increase in the adhesion strength through the sputtering prior to the coating and this could be attributed to a complete removal of compound layer from the plasma nitrided surface and to an increase in the surface roughness after sputtering.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2007년도 춘계학술대회 논문집
• /
• pp.318-321
• /
• 2007

This paper is concerned with improvement of surface quality of a sheet metal member in the stamping process. The CAE procedure of the stamping process is utilized in order to investigate cause of surface troubles and to improve surface quality. A complicated shape of the sheet metal member can induce surface troubles such as wrinkles because of insufficient tensions force and non-uniform contact of a blank sheet with tools. This paper proposes two guidelines such as a change of tool shape and added draw-beads on the tool surface in order to increase tension forces and to induce uniform contact. The proposed guidelines are verified with the CAE of the stamping process. The CAE results show that the changed shape of tools and added draw-beads can reduce the amount of wrinkles and improve surface quality.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2003년도 춘계학술대회 논문집
• /
• pp.1682-1687
• /
• 2003

Die polishing technology is very critical to determine quality and performance of the final products. Generally, the rotation-type tool is used most widely in the polishing process. However it is difficult to make the mirror surface, because the method using the rotation-type tool causes a lot of tiny scratch on the polished surface. This paper proposes a new method using the oscillation-type tool that reduces the scratch and improves the surface roughness. As result. the mirror surface was able to obtain by using the oscillation-type tool. AE is known to be closely related to material removal rate(MRR). As the surface is rougher, MRR gets larger and AE increase. The surface roughness can be indirectly estimated using the AE signal measured during automatic die polishing process. In this study. an AE sensor based monitoring system was developed to investigate the relation the level of AE RMS with the surface roughness during polishing process.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2004년도 추계학술대회 논문집
• /
• pp.1390-1393
• /
• 2004

In the present industry, three-dimensional colored shape has required for realistic prototype in rapid manufacturing. Z-corporation developed 3D printer which can color three-dimensional prototype but this process can't be adopted to other rapid prototype products and spend much time and cost coloring 3D shape. In this study a new coloring process on three-dimensional surface is proposed for realistic prototype. Three-dimensional surface coloring apparatus is composed of HP ink jet head and X-Y plotter. Distance and angle between ink jet nozzle and 3D surface are set as process parameter. Based on the experiment of process parameters, it is shown that distance and angle affected on printed image on 3D surface. Circle and line shape are chosen as standard image shape because the shape has widely used as standard in 2D printing. Consequently, the distorted image on 3D surface is corrected by transformed input image data.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1993년도 한국자동제어학술회의논문집(국내학술편); Seoul National University, Seoul; 20-22 Oct. 1993
• /
• pp.1024-1030
• /
• 1993

In manufacturing press die with free surface, grinding operation is an important post process for surface finish and dimensional accuracy. With the advancement of NC technology. surface grinding operation is increasingly replaced by the gantry type manipulator. As the mechanics for grinding operation is different from machining operation, conventional CAM system for machining operation is hard to apply. In this. paper, we develop a five-axis CAM system by which an efficient gantry trajectory can be planned and verified. The developed system consists of four conceptual modules; namely CAD, PROCESS. CAM, and ANALYSIS. In the CAD module, the machined surface is represented by CL-data or surface modeler, and process parameters are specified by the PROCESS module. Then, the CAM module generates a series of grinding paths based on the grinding mechanics together with process databases for tool spaces and grinding conditions. The generated paths are verified via ANALYSIS module. Validation via real experiments is left for further study.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2001년도 춘계학술대회 논문집
• /
• pp.930-933
• /
• 2001

Titanium Alloys used in this experiment has an good corrosion resistance and specific strength, and is the new material developed for medical supplies living goods. In this study the rolled titanium alloy is done by annealing, solution heat-treatment and aging and then is worked by wire EDM. With changing the process conditions, the process properties of surface hardness, surface roughness, shape of process surface and the analysis of ingredients are measured through experiment repeating main cut and finish cut. It is confirmed to gain good measure values as increasing the number of processing of wire EDM. In this experiment the phenomena of processing is studied and the appropriate process condition is proposed.

• 동력기계공학회지
• /
• 제6권2호
• /
• pp.54-59
• /
• 2002

The principle of the FDM(fused deposition modeling) process is based on the layer by layer manufacturing technology, like other RP(rapid prototyping) process. In the FDM process, each layer may have different shape. Therefore, the built model may have stairs shape on its surface. This stairs shape is one of the serious problems in the FDM process. Thus in this study, cube models and spherical models were fabricated by FDM process to investigate the influence of injection amount on surface roughness. Models with various road width were also built to investigate the influence of road width on surface roughness. Surface roughness of the models was measured and analyzed. The result obtained in this study are expected to help selecting the part build orientation for optimum surface roughness.

• 한국레이저가공학회:학술대회논문집
• /
• 한국레이저가공학회 2006년도 춘계학술발표대회 논문집
• /
• pp.60-65
• /
• 2006

Previous studies demonstrated that laser ablation under transparent liquid can result in ablation enhacement and particle removal from the surface. In this work, the liquid-assisted excimer laser ablation process is examined fer polyethylene terephthalate (PET), polymethyl methacrylate (PMMA), Si, and alumina with emphasis on ablation enhacement, surface topography, and debris formation. In the case of PET and PMMA, the effect of liquid is analyzed both fer thin water film and bulk water. As the ablation enhanement by liquid is already known for Si and alumina, the analysis focuses on surface topography and debris formation resulting from the liquid-assisted laser ablation process. The results show that application of liquid increases the ablation rate of PMMA while that of PET remains unchanged even in the liquid-assisted process. It is also revealed that the liquid can significantly improve the surface quality by reducing the debris deposition. However, the surface roughness is generally deteriorated in the liquid-assisted process. The surface toporaphy is found to be strongly dependent on the method of liquid application, i.e., thin film or bulk liquid.