• 한국초전도ㆍ저온공학회논문지
• /
• 제12권1호
• /
• pp.1-5
• /
• 2010

Silver stabilizing layer of coated conductor has been prepared by dip coating method using organic silver complexes containing 10 wt% silver as a starting material. Coated silver complex layer was dried in situ with hot air and converted to crystalline silver by post heat treatment in flowing oxygen atmosphere. A dense continuous silver layer with good surface coverage and proper thickness of 230 nm is obtained by multiple dip coatings and heat treatments. The film heat treated at $500^{\circ}C$ showed good mechanical adhesion and crystallographic property. The interface resistivity between superconducting YBCO layer and silver layer prepared by dip coating was measured as $0.67\;{\times}\;10^{-13}\;{\Omega}m^2$. Additional protecting copper layer with the thickness of $20\;{\mu}m$ was successfully deposited by electroplating. The critical current measured with the specimen prepared by dip coating and sputtering on same quality YBCO layer showed similar value of ~140 A and proved its ability to replace sputtering method for industrial production of coated conductor.

• Corrosion Science and Technology
• /
• 제19권2호
• /
• pp.89-99
• /
• 2020

The inhibition of pitting corrosion failure of copper sprinkler tubes in wet sprinkler systems was studied. First, an apparatus and technology for removing air in the sprinkler tubes by vacuum pumping and then filling the tubes with water were developed. Using this apparatus and technology, three methods for inhibiting the pitting corrosion of the copper sprinkler tubes installed in several apartment complexes were tested. The first one was filling the sprinkler tubes with water bubbled by high-pressure nitrogen gas to reduce the dissolved oxygen concentration to lower than 2 ppm. In the second method, the dissolved oxygen concentration of water was further reduced to lower than 0.01 ppm by sodium sulfite. In the third method, the sprinkler tubes were filled with benzotriazole (BTAH) dissolved in water. The third method was the most effective, reducing the failure frequency of the sprinkler tubes due to pitting corrosion by more than 80%. X-ray photoelectron spectroscopy analyses confirmed that a Cu-BTA layer was well coated on the inside surface of the corrosion pit, protecting it from corrosion. A potentiodynamic polarization test showed that BTAH should be very effective in reducing the corrosion rate of copper in the acidic environment of the corrosion pit.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2013년도 제45회 하계 정기학술대회 초록집
• /
• pp.70-70
• /
• 2013

As the costs of carbon-footprinetd fuels grow continuously and simultaneously atmospheric carbon dioxide concentration increases, solar fuels are receiving growing attention as alternative clean energy carriers. These fuels include molecular hydrogen and hydrogen peroxide produced from water, and hydrocarbons converted from carbon dioxide. For high efficiency solar fuel production, not only light absorbers (oxide semiconductors, Si, inorganic complexes, etc) should absorb most sunlight, but also charge separation and interfacial charge transfers need to occur efficiently. With this in mind, this talk will introduce the fundamentals of solar fuel production and artificial photosynthesis, and then discuss in detail on photoelectrochemical (PEC) water splitting and CO2 conversion. This talk largely divides into two section: PEC water oxidation and PEC CO2 reduction. The former is very important for proton-coupled electron transfer to CO2. For this oxidation, a variety of oxide semiconductors have been tested including TiO2, ZnO, WO3, BiVO4, and Fe2O3. Although they are essentially capable of oxidizing water into molecular oxygen, the efficiency is very low primarily because of high overpotentials and slow kinetics. This challenge has been overcome by coupling with oxygen evolving catalysts (OECs) and/or doping donor elements. In the latter, surface-modified p-Si electrodes are fabricated to absorb visible light and catalyze the CO2 reduction. For modification, metal nanoparticles are electrodeposited on the p-Si and their PEC performance is compared.

• 공업화학
• /
• 제21권1호
• /
• pp.58-62
• /
• 2010

$TiOSO_4$와 다층벽탄소나노튜브(MWCNT)를 사용하여 가수분해법으로 CNT-$TiO_{2}$ 나노복합체를 제조하였다. 제조된 $TiO_{2}$-CNT 복합체의 CNT는 아나타제 $TiO_{2}$에 균일하게 분산되어 있으며 MWCNT의 첨가량이 증가함에 따라 결정성 탄소의 비율과 O/Ti 비율이 증가함을 확인할 수 있다. CNT-$TiO_{2}$복합체의 광활성 및 오염물 흡착능력을 UV 조사 시간에 따른 메틸렌블루의 분해정도로 확인하였다. MWCNT의 비율이 높아질수록 높은 흡착능과 광분해능을 나타내었다. 이는 MWCNT의 높은 비표면적, 산소포함 관능기, 낮은 밴드갭 에너지, 높은 전기전도성, 높은 부피 대 표면적 비율, 균일한 구조 및 특성으로 인하여 CNT-$TiO_{2}$ 복합체의 광활성에 도움을 주는 것으로 보인다.

• Bulletin of the Korean Chemical Society
• /
• 제31권11호
• /
• pp.3118-3122
• /
• 2010

The water soluble redox polymer, poly(N-vinylimidazole) complexed with Os(4,4'-dichloro-2,2'-bipyridine)$_2Cl]^+$ (PVI-[Os(dCl-bpy)$_2Cl]^+$), was electrodeposited on the surface of a glassy carbon electrode by applying cycles of alternating square wave potentials between 0.2 V (2 s) and 0.7 V (2 s) to the electrode in a solution containing the redox polymer. The coordinating anionic ligand, $Cl^-$ of the osmium complex, became labile in the reduced state of the complex and was substituted by the imidazole of the PVI chain. The ligand substitution reactions resulted in crosslinking between the PVI chains, which made the redox polymer water insoluble and caused it to be deposited on the electrode surface. The deposited film was still electrically conducting and the continuous electrodeposition of the redox polymer was possible. When cycles of square wave potentials were applied to the electrode in a solution of bilirubin oxidase and the redox polymer, the enzyme was co-electrodeposited with the redox polymer, because the enzymes could be bound to the metal complexes through the ligand exchange reactions. The electrode with the film of the PVI-[Os(dCl-bpy)$_2Cl]^+$ redox polymer and the co-electrodeposited bilirubin oxidase was employed for the reduction of $O_2$ and a large increase of the currents was observed due to the electrocatalytic $O_2$ reduction with a half wave potential at 0.42 V vs. Ag/AgCl.

• Carbon letters
• /
• 제8권2호
• /
• pp.108-114
• /
• 2007

In this work, activated carbon (AC) after $HNO_3$ modification was used as the support during the production of supported $TiO_2$ to increase the high deposition efficiency and the photocatalytic activity. The results of $N_2$ adsorption showed that the BET surface area of samples decreased with an increasing of the concentration of $HNO_3$ due to the penetration of $TiO_2$. From XRD data, a single crystal structure of anatase peak was observed in diffraction patterns for the AC coated with titanium complexes. From the SEM results, almost all particles were aggregated with each other at the carbon surface and AC was covered with $TiO_2$ particles in all of the samples. The EDX spectra show the presence of C, O, Ti and other elements. It was also observed a decreasing of amount of C content with increasing Ti and O content from the EDX. The results of FT-IR revealed that the modified AC contained more surface oxygen bearing groups than that of the original AC. The effect of surface acidity and basity calculated from Boehm titration method was also evaluated from correlations as a function of NaOH, $NaHCO_3$, and $Na_2CO_3$ uptake. The surface modification of AC by $HNO_3$ leads to an increase in the catalytic efficiency of AC/$TiO_2$ catalysts, and the catalytic efficiency increases with increasing of $HNO_3$ concentration.

• 한국미생물·생명공학회지
• /
• 제48권1호
• /
• pp.12-23
• /
• 2020

Edible films containing antimicrobial agents can be used as safe alternatives to preserve food products. Essential oils are well-recognized antimicrobials. However, their low water solubility, volatility and high sensitivity to oxygen and light limit their application in food preservation. These limitations could be overcome by embedding these essential oils in complexed product matrices exploiting the encapsulation efficiency of β-cyclodextrin. This study focused on the maximization of β-cyclodextrin production using cyclodextrin glucanotransferase (CGTase) and the evaluation of its encapsulation efficacy to fabricate edible antimicrobial films. Response surface methodology (RSM) was used to optimize CGTase production by Brevibacillus brevis AMI-2 isolated from mangrove sediments. This enzyme was partially purified using a starch adsorption method and entrapped in calcium alginate. Cyclodextrin produced by the immobilized enzyme was then confirmed using high performance thin layer chromatography, and its encapsulation efficiency was investigated. The clove oil/β-cyclodextrin inclusion complexes were prepared using the coprecipitation method, and incorporated into chitosan films, and subjected to antimicrobial testing. Results revealed that β-cyclodextrin was produced as a major product of the enzymatic reaction. In addition, the incorporation of clove oil/β-cyclodextrin inclusion complexes significantly increased the antimicrobial activity of chitosan films against Staphylococcus aureus, Staphylococcus epidermidis, Salmonella Typhimurium, Escherichia coli, and Candida albicans. In conclusion, B. brevis AMI-2 is a promising source for CGTase to synthesize β-cyclodextrin with considerable encapsulation efficiency. Further, the obtained results suggest that chitosan films containing clove oils encapsulated in β-cyclodextrin could serve as edible antimicrobial food-packaging materials to combat microbial contamination.

• 한국해양학회지
• /
• 제13권2호
• /
• pp.17-25
• /
• 1978

우리 나라에서의 연안수질조사나 해양특성조사는 현재까지 단편적으로 이루어진 것이 상당히 많다. 해방전에 조사된 것을 제외하면 1960년대 전반까지는 조사된 것이 별로 없으나 후반에 들어와서는 원(1963,1964), 박과 김(1967), 장과 배(1968), 박 등(1969), 이 등(1969)의 양식장주변을 위주로 한 조사가 시작되었으며, 경제성장과 때를 같이하여 1970년대 전반에 들어와서는 원과 박(1970), 김(1970), 원(1970), 최 등(1970), 최와 정(1971), 홍 등(1971), 강(1972), 최와 정(1972), 황 (1972), 원과 박(1973), 김 등((1974), 이 등 (1974), 노 등 (1975), 곽과 이(1975) 박(1975a,b), 곽(1976, 1977) 등 연안수질의 현황에 대하여 집중적으로 조사가 행해졌다. 그러나 어떤 한 해역에 있어서의 해양학적 특성이나 영양염 또는 중금속을 조사했ㅇ르 뿐 그 이외의 해역을 같은 계절에 조사해서 비교 분석한 사실은 거의 없다

• 한국수산과학회지
• /
• 제43권2호
• /
• pp.146-158
• /
• 2010

In order to evaluate the characteristics of sediments and pollution by organic matter and metallic elements in intertidal sediments along the southwestern coast of Korea, we measured various geochemical parameters, including the mean grain size (Mz), water content (WC), ignition loss (IL), chemical oxygen demand (COD), acid volatile sulfide (AVS), and metallic elements (Al, Fe, Cu, Pb, Zn, Cd, Cr, Mn, Hg, As), in intertidal surface sediments. The Mz of the surface sediments ranged from 2.1 to 8.3$\phi$, indicating that the surface sediments consist of various sedimentary facies, such as sand, slightly gravelly mud, sandy mud, and silt. The IL and COD in surface sediment ranged from 0.8 to 5.5% (mean $2.9\pm1.2%$) and from 3.9 to $13.8\;mgO_2/g{\cdot}dry$ (mean $8.5\pm2.6\;mgO_2/g{\cdot}dry$), respectively, which were lower than the values for surface sediment in areas near fish and shellfish farms or industrial complexes. No AVS was detected at any sampling station, despite various sedimentary facies. Most of metallic elements in surface sediments showed relatively good positive correlations with Mz and IL, which imply that the concentrations of metallic elements are mainly controlled by grain size and the organic matter content. The concentrations of metallic elements, except As, at some stations were considerably lower than those in the Sediment Quality Guideline (Effect Range Low, ERL) proposed by the National Oceanic and Atmospheric Administration (NOAA) in the United States. Similarly, the geoaccumulation index (Igeo) class indicated that pollution by metallic elements in intertidal surface sediment, except As, was moderate or non-existent. Our results imply that the intertidal surface sediments along the southwestern coast of Korea are not polluted by organic matter and metallic elements and are healthy for benthic organisms.

• 한국수산과학회지
• /
• 제48권4호
• /
• pp.542-554
• /
• 2015

Grain size, the content of ignition loss (IL), and the concentrations of chemical oxygen demand (COD), acid volatile sulfide (AVS), and trace metals (Fe, Mn, Cu, Pb, Zn, Cd, Cr, As, and Hg) in surface sediments from the Taehwa River estuary, Ulsan, were measured to evaluate pollution levels and potential ecological risks of organic matter and trace metals in estuarine sediment. The mean grain size (Mz) of sediments in the study region ranged from $-0.8-7.7{\varphi}$ (mean $2.8{\pm}2.4{\varphi}$). Surface sediments in the upstream region of the Taehwa River were mainly composed of coarse sediments compared to the downstream region. The concentrations of IL, COD, AVS and trace metals in the sediment were much higher at downstream sites of Myeongchon Bridge in the vicinity of industrial complexes than at upstream sites of those in the vicinity of the residential areas due to the anthropogenic input of organic matter and trace metals by industrial activities. On the basis of several geochemical assessment techniques [sediment quality guidelines (SQGs), enrichment factor (EF), geoaccumulation index ($I_{geo}$), pollution load index (PLI) and ecological risk index (ERI)], the surfaces sediments in the study region are not highly polluted for trace metals, except for As. However, the higher concentrations in downstream study regions of the Taehwa River could impact benthic organisms including shellfish (i.e. Manila clam) in sediments.