• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.52 no.6
• /
• pp.261-266
• /
• 2003

We investigated the effect of oxygen plasma treatment of indium-tin oxide(ITO) surface on the performance of electroluminescence(EL) devices. ITO surface treated oxygen plasma has been analyzed using atomic force microscope(AFM) and X-ray photoelectron spectroscopy(XPS), to investigate the relations between the properties of the ITO surface and the properties of the current-voltage-luminance(I-V-L) characteristics of the fabricated OLED with the structure of ITO(plasma treatment) / TPD / Alq$_3$/ Al. It is found that the oxygen plasma treatment of ITO anode improve the hole injection of the OLED due to the modification of the surface states. The treated ITO anode nay be low voltage with high luminance efficiency.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.25 no.10
• /
• pp.1590-1596
• /
• 2001

The shot peening process is most often used to improve fatigue properties of metal parts. The single most critical parameter of the shot peening process is the shot ball itself. Without the correct quality media, all other shut peening parameters are extraneous and the desired fatigue improvement and consistency of improvement will not be achieved. Shot peening involves modifications of the surface and subsurface condition of a material that can be described by the change of the residual stresses, the hardness, and the surface roughness. This Paper Presents the shot peening to optimize the shot ball parameters. The effect of shot peening parameter on the surface roughness, surface hardness and residual stress are investigated.

• Carbon letters
• /
• v.16 no.1
• /
• pp.34-40
• /
• 2015

In this study, in order to improve the thermal and electrical properties of epoxy/graphene nanoplatelets (GNPs), surface modifications of GNPs are conducted using silane coupling agents. Three silane coupling agents, i.e. 2-(3,4-epoxycyclohexyl)-ethyltrimethoxysilane (ETMOS), 3-glycidoxypropyltriethoxysilane (GPTS), and 3-glycidoxypropyltrimethoxysilane (GPTMS), were used. Among theses, GPTMS exhibits the best modification performance for fabricating GNP-incorporated epoxy composites. The effect of the silanization is evaluated using transmission electron microscopy (TEM), scanning electron microscopy, thermogravimetric analysis, and energy dispersive X-ray spectroscopy. The electrical and thermal conductivities are characterized. The epoxy/silanized GNPs exhibits higher thermal and electrical properties than the epoxy/raw GNPs due to the improved dispersion state of the GNPs in the epoxy matrix. The TEM microphotographs and Turbiscan data demonstrate that the silane molecules grafted onto the GNP surface improve the GNP dispersion in the epoxy.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2009.11a
• /
• pp.33.2-33.2
• /
• 2009

Block copolymer lithography has attracted great attention for emerging nanolithography since nanoscaleperiodic patterns can be easily obtained through self-assembly process without conventional top-down patterning process. Since the morphologies of self-assembled block copolymer patterns are strongly dependent on surface energy of a substrate, suitable surface modification is required. Until now, the surface modification has been studied by using random copolymer or self-assembled mono layers (SAMs). However, the research on surface modifications has been limited within several substrates such as Si-based materials. In present study, we investigated the formation of block copolymer on Au substrate by $O_2$ plasma treatment with the SAM of 3-(p-methoxy-phenyl)propyltrichloro-silane [MPTS, $CH_3OPh(CH_2)_3SiCl_3$]. After $O_2$ plasma treatment, the chemical bonding states of the surface were analyzed by X-ray photoelectron spectroscopy (XPS). The static contact angle measurement was performed to study the effects of $O_2$ plasma treatment on the formation of MPTS monolayer. The block copolymer nanotemplates formed on Au surface were analyzed by scanning electron microscopy. The results showed that the ordering of self-assembled block copolymer pattern and the formation of cylindrical nano hole arrays were enhanced dramatically by oxygen plasma treatment. Thus, the oxidation of gold surface by $O_2$ plasma treatment enables the MPTS to form the monolayer assembly leading to surface neutralization of gold substrates.

• Membrane and Water Treatment
• /
• v.1 no.2
• /
• pp.103-120
• /
• 2010

Surface modification of microfiltration and ultrafiltration membranes has been widely used to improve the protein adsorption resistance and permeation properties of hydrophobic membranes. Several surface modification methods for converting conventional membranes into low-protein-binding membranes are reviewed. They are categorized as either physical modification or chemical modification of the membrane surface. Physical modification of the membrane surface can be achieved by coating it with hydrophilic polymers, hydrophilic-hydrophobic copolymers, surfactants or proteins. Another method of physical modification is plasma treatment with gases. A hydrophilic membrane surface can be also generated during phase-inverted micro-separation during membrane formation, by blending hydrophilic or hydrophilic-hydrophobic polymers with a hydrophobic base membrane polymer. The most widely used method of chemical modification is surface grafting of a hydrophilic polymer by UV polymerization because it is the easiest method; the membranes are dipped into monomers with and without photo-initiators, then irradiated with UV. Plasma-induced polymerization of hydrophilic monomers on the surface is another popular method, and surface chemical reactions have also been developed by several researchers. Several important examples of physical and chemical modifications of membrane surfaces for low-protein-binding are summarized in this article.

• Journal of Advanced Marine Engineering and Technology
• /
• v.36 no.8
• /
• pp.1083-1090
• /
• 2012

Copper alloys are widely used for casting materials including ship's propellers and pump impellers as they provide high corrosion resistance. In addition, the demand for these alloys is increasing with rapid growth of offshore structures and exploitation of various substitute energy sources. However, they require regular maintenance because of erosion and cavitation damages induced by exposure to marine environment at high speed flows for a long period of time. Water cavitation peening have received attention as one of surface modifications for durability improvement of the copper alloys. This is a environment friendly technology without influence of heat and easily applicable to casting materials. In this research, water cavitation peening was employed in distilled water for copper alloy castings as a function of time and evaluation of corrosion resistance was followed in seawater for the modified surface by using electrochemical methods. The result suggests that the water cavitation peening for 2 minutes was found to be the optimal peening parameter in terms of durability and corrosion resistance.

• Journal of the Korean Society of Industry Convergence
• /
• v.12 no.2
• /
• pp.99-105
• /
• 2009

Among a few items with world wide competitiveness are the semiconductor and the LCD. Grinding/polishing is the most significant process in manufacturing semiconductor wafers and LCD panels, the most critical quality of which is the precision rate of the machined surfaces. It is well known that the control of the vibrations is the major factor in maintaining superb machined surfaces. In this paper the dynamic properties of a grinding machine have been investigated through the frequency analysis test and the computer simulation to deduce ideas of design modifications for improved stability. The alterations have been applied to the simulation model, which is supposed to have identical dynamic property with the original structure, to identify the effects and to finally achieve the satisfactory level of stability. The result shows that the machine can have much improved stability with relatively simple design changes, and also can improve the surface quality of the products.

• Carbon letters
• /
• v.3 no.4
• /
• pp.219-225
• /
• 2002

The two-step surface modifications of activated carbon was carried out to improve the adsorption capacity of toxic heavy metal ions in liquid phase. Physical and chemical properties of the as-received activated carbon (AC) and two kinds of surface-modified activated carbons ($1^{st}AC$ and $2^{nd}AC$) were evaluated through the BET analysis, surface acidity, and oxides measurements. Specific surface area and pore volume did not significantly change, but surface oxide-group remarkably increased by the surface modification. Equilibrium and batch adsorptions of the various metals, such as Pb, Cd, and Cr, using AC, $1^{st}AC$, and $2^{nd}AC$ were performed at initial pH 5. The adsorption capacity and rate of $2^{nd}AC$ were higher than those of AC and $1^{st}AC$. The carboxylic/sodium carboxylate complex groups were developed from the two-step surface modification of activated carbon, which strongly affected the adsorption of metal ions.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2015.05a
• /
• pp.43-44
• /
• 2015

Electrodeposited Ni and Ni-SiC composite coatings were prepared on Cu substrates by using the Ni-Sulfamate electrolytic bath. Thus prepared samples were subjected for the two different types of post surface modification techniques; i.e. Laser Surface Texturing (LST) and Ultrasonic Nano Surface Modification (UNSM), respectively in order to investigate their effects on surface and interface related properties of the coatings. Hemispherical dimples, with 80 to 200 um dimple spacing, were created and examined on the surfaces of the materials studied. The results revealed that micro-surface texturing with 150 um dimple spacing considerably improved the coefficient of friction. Dimple spacing accuracy and incorporated second phase ceramic particles both contributed significantly to reduction in coefficient of friction. On the other hand, application of UNSM considerably modified the surface topography, led to increase the Vickers microhardness, and reduced the wear and coefficient of friction as compared to non UNSM treated Ni and Ni-SiC samples.

• Journal of Dental Rehabilitation and Applied Science
• /
• v.29 no.2
• /
• pp.141-151
• /
• 2013

The nano-surface modification techniques could be classified; internal modifications which enhance surface roughness and porosity in nano level and external modifications as nano particle coating. Nano-modified implant surface has various morphograpies such as nanotube, nanopit, nanonodule and polymorphic structures. Creating surface depends upon preparation method and material, however, there is no standard preparation technique not yet. The nano-modified surfacet is electrochemically stable comparing with the surface modified in micron level. Nano-modified surface has little cytotoxicity, stimulates osteoblast proliferation and differentiation. Moreover, it decreases soft tissue intervention by interrupting the proliferation of fibroblast. Nanostructure has similar size and shape with cells and proteins, consequently leads to good biocompatibility and enhanced osseointegration. However, the actual effect in vivo is limited, due to the distance of effect. Even if nano-modified surface has antibiotic property due to photocatalysis, short duration time makes clinical application questionable. Further investigations should focus on the optimal nano-modified surface, which has many potentials.