• 한국표면공학회지
• /
• 제35권1호
• /
• pp.17-32
• /
• 2002

Electroplating methods by molten salts and non-aqueous melts were employed for aluminium coating on STS 316L stainless steel. After coated with Ni or non-coated surface on stainless steel, Al pulse plating was carried out in two different types of electrolytes at room temperature. The Al layer from $AlCl_3$-TMPAC melts could not obtain appreciable thickness for engineering application due to chemical reactions between deposits and moisture of air. However, The Al coating by pulse plating in the Ethylbenzene-Toluene-$AlBr_3$ systems was found to be solid coating layer with a few $\mu\textrm{m}$ scale. The conductivity of Ethylbenzene-Toluene-$AlBr_3$ electrolyte was as functions of time and agitation. By seven days exposure after mixing of the electrolyte, Al-deposited layer shows uniform and near by pore-free with high current density (higher than 30mA/$\textrm{cm}^2$). The roughness and imperfection of coating layer were decreased with a increasing agitation speed. It was found that the optimum condition for the Al pulse plating on the 316L stainless steel was a 400mA peak current, duty cycle, $t_{on}$ $t_{ off}$=3ms/1ms, and a current density of 30mA/$\textrm{cm}^2$.

• 한국어류학회지
• /
• 제8권2호
• /
• pp.47-56
• /
• 1996

대한해협은 한국연안수, 동해저층냉수, 대마난류수의 영향을 받는 해역으로 매우 다양한 치자어가 출현였으며 이 중 멸치 치자어는 거의 대부분 대마난류수가 영향을 미치는 해역에 출현하였다. 멸치는 전 계절에 걸쳐 출현하였으며, 여름철에 가장 출현량이 많았다. 수층별로는 봄, 여름철에는 표층보다는 중층(30~70m)에 많이 분포하고 100m 이상의 저층에는 출현량이 적었다. 가을철에는 표층에 가장 많고 수심이 깊어질수록 출현량이 줄어드는 양상을 보였다. 겨울철에는 표층과 저층보다는 중층(30~50m)에 많은 양이 분포하였다. 주 야에 따른 수층별 분포는 주간에는 30~70m 사이의 중층에, 야간에는 표층에 많이 분포하였다 수층별 분포량은 계절, 주 야에 따라 차이가 있으나, 100m 이내의 수층에 주로 분포하며 여름과 가을철에는 수온약층의 윗 수층에 대부분 분포하였다.

• 한국표면공학회지
• /
• 제30권5호
• /
• pp.347-354
• /
• 1997

Composite plating is a method of co-depositing fine particles of metallic, non-metallic compound or polymers in the plated layer to improve material properties such as were-resistance, lubrication, or corrosion resistance. Graded Ni-Sic composite coating were produced in this research. Prior to produce Graded Ni-SiC composite coatings, effects of particle size, particle content, pH of electrolyte, temperature, current density, stirring rate on the amount of SiC deposited in the Ni layer were investigated. By manipulating current density and plating time properties of these coating were evaluated by micro-indentation hardness test.

• Ocean and Polar Research
• /
• 제36권2호
• /
• pp.165-177
• /
• 2014

In an effort to investigate the structure and variability of the coastal current in the East Sea, a moored ADCP observation was conducted off Uljin from late May to mid-October 2006. Owing to the transition of season from summer to autumn, the features of the current and wind can be divided into two parts. Until mid-August (Part-I), a southward flow is dominant at all depths with a mean alongshore velocity of 4.2~8.9 cm/s but northward winds are not strong enough to reverse the near-surface current. During Part-II, a strong northward current occurs frequently in the upper layer but winds are predominantly southward including two typhoons that have deep-reaching influence. Profile of mean velocity has three layers with a northward velocity embedded at 12~28 m depth. The near-surface current of Part-II significantly coheres with winds at 4-8 day periods with a phase lag of about 12 hours. The modal structure of the current obtained by EOF analysis is: (1) Mode-1, having 83.6% of total variance, represents the current in the same direction at all depths corresponding to the southward North Korean Cold Current (NKCC). (2) Mode-2 (11.7%) reveals a two-layer structure that can be explained by the northward East Korean Warm Current (EKWC) in the upper layer and NKCC in the lower. (3) Mode-3 (2.6%) has three layers, in which the EKWC is reversed near the surface by opposing winds. This mode is particularly similar to the mean velocity profile of Part-II.

• 한국표면공학회지
• /
• 제37권2호
• /
• pp.110-118
• /
• 2004

The corrosion of pure titanium (CP- Ti Grade 2) and titanium alloy (Ti6Al4V ELI) were studied under various conditions of simulated body fluids. The static immersion test and the electrochemical test were performed in accordance with ISO 10271 : 2001. For the electrochemical test, the open circuit potential was monitored as a function of time, and the cyclic polarization curve was recorded. The corrosion resistance was evaluated from the values of corrosion potential, passivation current density, breakdown potential, and the shape of hysteresis etc. The effects of alloy type, surface condition, temperature, oxygen, and constituents in the fluids such as acid, chloride were estimated. Both specimens had extremely low dissolution rate in the static immersion test. They showed strong passivation characteristics in the electrochemical test. They maintained negligible current density throughout the wide anodic potential range. The passive layer was not broken up to 2.0 V (vs. SCE). The hysteresis and the shift of passivation potential toward the anodic direction was observed during the reversed scan. The passivation process appeared to be accelerated by oxygen in air or that dissolved in the fluids. The passivation also proceeded without oxygen by the reaction of constituents in the fluids. Acid or chloride in the fluids, specially later weakened the passive layer, and then induced higher passivation current density and less shift of passivation potential in the reversed scan. CP-Ti Grade 2 was more reactive than Ti6Al4V ELI in the fluids containing acid or chloride, but thicker layer produced on its surface provided higher corrosion resistance.

• 한국정밀공학회지
• /
• 제14권5호
• /
• pp.53-59
• /
• 1997

This study has been performed to inmvestigate MRR(metal removal rate), REW(relative electrode wear), surface roughness, heat transumutation layer and microhardness distribution in cross-section of the machined surface with various pulse-on duration and peak pulse current, using the copper and graphite electrode on the heat treated STD11 which is extensively used for metallic molding steel with the EDM. The results obtained are as follows; a) There exists critical pulse-on duration(If Ip equals 5A, .tau. on is 50 .mu. s) which shows the the maximum MRR in accordance with peak oulse current and the MRR decreases when the pulse-on duration exceeds the critical pulse-on during because of the abnormal electric discharge. b) Safe discharge is needed to make maximum of MRR and the metalic organization must be complicated for discharge induction. c) Graphite has much more benefits than copper electrode when rapid machining is done without electrode wear. d) The most external surface has the highest microhardness because of car- burizing from heat analysis of the dielectric fluid and the lower layar of the white covered layer has lower microhar dness than base matal because of softening.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1999년도 추계학술대회 논문집
• /
• pp.177-180
• /
• 1999

In this paper, we studied Surface Discharge Type Flat Fluorescent Lamp(FFL) with High Luminance for LCD Backlighting. This lamp is Surface Discharge Type structure with a pair of Sodalime glass, insulator layer, phosphor layer, and Xe gas gap. There are two influences of Electric field on different dielectric thickness. The Electric field difference at the dielectric layer itself enhances minimum value of firing voltage and luminance uniformity. So, we measured the Electric filed at 0.5mm, 1mm gap length and discharge voltage for difference dielectric layer thickness. In experiment result, the thicker dielectric layer has higher firing voltage and lower current.

• Bulletin of the Korean Chemical Society
• /
• 제23권1호
• /
• pp.71-74
• /
• 2002

The apparent barrier height for charge transfer through an interfacial water layer between a Pt/Ir tip and a gold surface has been measured using STM technique. The average thickness of the interfacial water layer inside an STM junction was controlled by the amount of moisture. A thin water layer on the surface was formed when relative humidity was in the range of 10 to 80%. In such a case, electron tunneling through the thin water layer became the majority of charge transfers. The value of the barrier height for the electron tunneling was determined to be 0.95 eV from the current vs. distance curve, which was independent of the tip-sample distance. On the other hand, the apparent barrier height for charge transfer showed a dependence on tip-sample distance in the bias range of 0.1-0.5 V at a relative humidity of approximately 96%. The non-exponentiality for current decay under these conditions has been explained in terms of electron tunneling and electrochemical processes. In addition, the plateau current was observed at a large tip-sample distance, which was caused by electrochemical processes and was dependent on the applied voltage.

• Ocean and Polar Research
• /
• 제31권4호
• /
• pp.283-296
• /
• 2009

Oceanographic survey data were analyzed to understand the characteristics of a warm eddy observed in the Ulleung Basin in July 2005. The temperature distribution at 200 db and vertical sections provided evidence of the warm eddy in the Ulleung Basin (UWE05). Based on the 5$^{\circ}C$ isothermal line on 200 db temperature, the major axis was 160 km from southwest to northeast, and the minor axis was 80 km from southeast to northwest. The homogeneous layer in the thermocline of UWE05 had mean values of 10.40$^{\circ}C$ potential temperature, 34.35 psu salinity, and 26.37 kg/m$^3$ potential density (${\sigma}_{\theta}$) and provided evidence that UWE05 also existed during the winter of 2004-2005. A warm streamer initially flowed along the circumference of UWE05 and mixed with the upper central water. Two northward current cores were found on the western side of the measured current section at the central latitude of UWE05. One was the East Korean Warm Current (EKWC) and the other was the main stream of the western part of UWE05. Geostrophic transport of the upper layer (from the surface to the isopycnal surface of 26.9 ${\sigma}_{\theta}$) was approximately 2.5 Sv in the eastern side of UWE05. However, the measured transport was twice as large as the geostrophic transport. Mass conservation of geostrophic transport was well satisfied in the upper layer. The direct current measurements and geostrophic transport analysis showed that the EKWC meandered around UWE05.

• 한국표면공학회지
• /
• 제47권4호
• /
• pp.210-214
• /
• 2014

We investigated emission characteristics of tandem organic light emitting devices (OLEDs) with p-type materials as charge generation layer. The tandem OLEDs were fabricated by using $MoO_x$, $WO_x$, C60 and HATCN as p-type material or not using p-type material for charge generation. When HATCN was used as p-type material, it showed high current density at low applied voltage, but increase of efficiency was small because of charge unbalance in emitting layer. In case of tandem OLED not using p-type material, applied voltage increased remarkably because of difficulty of hole injection. In case of $MoO_x$, $WO_x$ or C60 as p-type material, current emission efficiency increased greatly. In particular, current emission efficiency of tandem OLED using $MoO_x$ as p-type material increased up to 3 times than current emission efficiency of single OLED. The Commission Internationale de l'Eclairage (CIE) 1931 color coordinates were changed by overlapping of 504 nm emission wavelength. As a result, emission efficiency of tandem OLED improved compared with single OLED, but driving voltage also increased by increase of organic layer thickness.