• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2008년도 춘계학술대회 논문집
• /
• pp.255-261
• /
• 2008

The importance of maintenance of rail surface defects is increasing according to the KTX operation. That is because during high speed operation of rolling stocks, rail surface defects shorten fatigue life of rail, accelerate track degradation and deteriorate ride comfort. Rail grinding has been applied for effective rail maintenance in Kyeong-Bu HS line. This paper evaluates the effectiveness of rail grinding in term of rail fatigue life. To this end, the stresses of the ground rail are measured under KTX running and the equivalent stress range is calculated by RMC after the frequency analysis done with Rainflow counting method. Also, Pamglen-Miner rule is applied to predict the fatigue life of ground rail. The result of the analysis shows that the fatigue life of ground rail is increased by 15%.

• 한국지진공학회:학술대회논문집
• /
• 한국지진공학회 1999년도 춘계 학술발표회 논문집 Proceedings of EESK Conference-Spring
• /
• pp.100-108
• /
• 1999

rectangular open or in-filled trenches(concrete and rubber) are often used to reduce the ground vibrations caused by propagating surface(Rayleigh) waves. This paper presents the experimental data for estimating the vibration screening effectiveness of open or in-filled trenches Field dynamic tests using the exciter which can generate the 100kN vertical cyclic load in the range of 100-250 Hz were performed. One hundred and twenty accelerometers to measure the ground response are used in 6 radial direction. To compare the effectiveness of the vibration isolation the contours of the amplitude ratio with the dimensionless parameters dividing by Rayleight wave lengths were presented.

• 한국가시화정보학회:학술대회논문집
• /
• 한국가시화정보학회 2002년도 추계학술대회 논문집
• /
• pp.81-84
• /
• 2002

Dispersion of coolant jets in a film cooling flow field is the result of a highly complex interaction between the film cooling jets and the mainstream. In order to investigate the effect of blowing ratios on the film cooling of turbine blade, cylindrical body model was used. Mainstream Reynolds number based on the cylinder diameter was $7.1\;\times\;10^4$. The free-stream turbulence intensity kept at $5.0\%$ by using turbulence grid. The effect of coolant flow rates was studied for blowing ratios of 0.9, 1.3 and 1.6, respectively. The temperature distribution of the cylindrical model surface is visualized by infrared thermography (IRT). Results show that the film-cooling performance may be significantly improved by controlling the blowing ratio. As blowing ratio increases, the adiabatic film cooling effectiveness is more broadly distributed and the area protected by coolant increases. The mass flow rate of the coolant through the first-row holes is less than that through the second-row holes due to the pressure variation around the cylinder surface.

• 신재생에너지
• /
• 제2권1호
• /
• pp.46-55
• /
• 2006

The performance enhancement of heat exchanger in the drying system using solar collector with evacuated tubes is analyzed. First, for this analysis, the heat loss from a reversed trapezoidal fin attached at the pipe is calculated as a function of convection characteristic number ratio, fin base length and fin tip length. Also, the optimum heat loss and fin tip length of the fin under certain conditions are presented. The overall surface effectiveness of the cylinder with reversed trapezoidal fins in the heat exchanger are shown as a function of half fin base height, fin lateral slope and fin tip length.

• 대한조선학회논문집
• /
• 제53권6호
• /
• pp.521-528
• /
• 2016

The surface of a naval ship emits infrared signature because it is mainly heated by the sun. In order to reduce infrared signature, it has been practiced to cool surface of the naval ship by using sea water. In this study, reduction effect of infrared signature was compared according to the parameters which affect emission of infrared signature in order to increase utility of sea water cooling. The analysis results by searching parameters, which can judge operation of sea water cooling, could be utilized as basic data for operation of the naval ship.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2001년도 추계학술대회 논문집
• /
• pp.71-76
• /
• 2001

In the surface measurement system using touch probe, probe radius compensation is a key factor for accuracy. In this paper we investigate methods for compensating probe radius so that the surface equation for an "unknown surface" can be efficiently derived. The developed algorithm derives the surface equation by the iterative procedure of estimation, verification, and modification . Since the procedure is applied only for the surface region exceeding the tolerance limit, an accurate surface equation can be obtained with less computation and measurement point. The validity and effectiveness of the algorithm was tested by numerical simulations. The results convinced us that the develop algorithm can be used for surface measurement and tool path planning for NC machining.

• 한국정밀공학회지
• /
• 제23권9호
• /
• pp.190-199
• /
• 2006

A new approach which combines implicit surface scheme and recursive subdivision method is suggested in order to fill the holes with complex shapes in the polygon model. In the method, a base surface is constructed by creating smooth implicit surface from the points selected in the neighborhood of holes. In order to assure C$^1$ continuity between the newly generated surface and the original polygon model, offset points of same number as the selected points are used as the augmented constraint conditions in the calculation of implicit surface. In this paper the well-known recursive subdivision method is used in order to generate the triangular net with good quality using the hole boundary curve and generated base implicit surface. An efficient anisotropic smoothing algorithm is introduced to eliminate the unwanted noise data and improve the quality of polygon model. The effectiveness and validity of the proposed method are demonstrated by performing numerical experiments for the various types of holes and polygon model.

• 한국생산제조학회지
• /
• 제8권6호
• /
• pp.105-112
• /
• 1999

In this paper we deal with tool interference problem in the case of compound surface machining. A new tool interference detection and correction method based on the envelope of the tool path is suggested to identify and correct the tool interference - not only within the local path of tool movement, but also outside of the tool path. Therefore, the developed strategy can be used to check the possible interference in any region of the surface. In order to analyze quantitatively the milled surface error produced by the tool interference, improved surface prediction model is also suggested in cutting process by general cutters. The effectiveness of the proposed method is demonstrated through simulation study.

• 소성∙가공
• /
• 제26권3호
• /
• pp.162-167
• /
• 2017

The tensile surface residual stress in the multi-pass drawn wire deteriorates the mechanical properties of the wire. Therefore, the evaluation of the residual stress is very important. Especially, the axial residual stress on the wire surface is the highest. Therefore, the objective of this study was to propose an axial surface residual stress prediction model of the multi-pass drawn steel wire. In order to achieve this objective, an elastoplastic finite element (FE) analysis was carried out to investigate the effect of semi-die angle and reduction ratio of the axial surface residual stress. By using the results of the FE analysis, a surface residual stress prediction model was proposed. In order to verify the effectiveness of the prediction model, the predicted residual stress was compared to that of a wire drawing experiment.

• 한국정밀공학회지
• /
• 제10권3호
• /
• pp.47-56
• /
• 1993

Typical plastic strains in the machined surface are very difficult to measure, since they are located within a very short distance from the surface and they change very rapidly. There is an alternative way to determine the residual strain in plastically deformed materials by measuring the grain size after a subsequent recrystallization precess. Although, this technique has been successfully applied by several researchers to find the plastic zone around notches and cracks in various materials and welding beads, few works have been reported using the recrystallization method to determine the residual strains in machined surface. Therefore, the purpose of this investigation is to explore the effectiveness of the recrystallization technique in machining applications and in particular, to find the effect of cutting parameters, i.e., depth of cut, rake angle, on the plastic strains. As the result, the recrystallization technique was succesfully applid to determine the plastic strain in machined surface.