• 한국해양공학회지
• /
• 제20권4호
• /
• pp.24-30
• /
• 2006

Different methods exist for the estimation of thermaldeformation of plates in the line heating process. These are based on the assumption of residual strains in the heat-affected zone, known as the method of inherent strains, or simulated relations between heating conditions and residual deformations. The purpose of this paper is to develop a simulator of thermal deformation in the line heating, using the artificial neural network. Curvature deformations for the plate-forming are investigated, which can be used as a prime deformation parameter in the process. The curvature of plates are calculated using the approximation of plate surface by NURBS. Line heating experiments for 11 specimens of different thickness and heating conditions were performed. Two neural networks predicting the maximum temperature and curvature deformations at the heating line are studied. It was concluded that the thermal deformations predicted by the neural network can be used in a line heating simulator, which is considered an attractive and practical alternative to the existing methods.

• 한국정밀공학회지
• /
• 제17권8호
• /
• pp.113-119
• /
• 2000

There are two major factors which affect the cam design : the pressure angle and the radius of curvature, Cam shape will have an instantaneous radius of curvature at every point. Even though the design constraint of the pressure angle has been satisfied the follower may still not complete the desired contact motion. If the radius of the follower roller is larger than the concave(negative) radius on the cam it occurs the gap between the cam and the follower roller at the contact point. And also if the curvature of the pitch curve of the cam is too sharp the cam profile may be undercut. This paper proposes a new approach which uses the relative velocity of the follower roller parallel to the tangent line at the contact point on the cam surface for determining the pressure angle and the relative acceeration for determining the radius of curvature.

• 대한기계학회논문집A
• /
• 제36권3호
• /
• pp.259-264
• /
• 2012

비자성체의 자유곡면 자기연마 공정에서 자기력 세기의 향상은 매우 중요하다. 비자성체 자유곡면의 표면에 발생하는 자기력의 세기에 따라 자기연마 입자가 가지는 수직 절삭력이 변화하기 때문이다. 이러한 자기력 향상을 위하여 전자석 배열 테이블이 적용된 제 2세대 자기연마공정이 비자성체의 자유곡면 자기연마에 적용된다. 본 연구에서는 이러한 제 2세대 자기연마공정에서 전자석 배열 테이블에 발생하는 자기력 세기 향상을 위한 극성배열 방법을 제시하고 이를 알루미늄합금의 곡률 자기연마에 적용하였다. 그 결과 볼록 및 오목 형상에서 각각 S-N-S와 S-N-N-N-S 극성 배열에서 가장 높은 표면거칠기의 향상을 확인하였다. 또한 상승 가공경로에서 상대적으로 높은 표면거칠기 향상을 나타내었다.

• KSTLE International Journal
• /
• 제5권2호
• /
• pp.44-48
• /
• 2004

A new type slider with optical components is going to be introduced on market for portalbe and high capacity disk drive, and it will show a great potential for high performance drive in the paper the dynamic behavior and static characteristics of silder for a small form factor optical disk drive have been investigated numerically by an in-house simulation code using FEM. A curvature effect is found when a slider is applied to a relatively small disk, which makes rolling characteristics worse due to the negative pressured generated at the air bearing surface because of the curvature of small disk diameter.

• 대한수학회보
• /
• 제54권1호
• /
• pp.159-175
• /
• 2017

We solve the $Bj{\ddot{o}}rling$ problem for constant mean curvature one surfaces in hyperbolic three-space and in de Sitter three-space. That is, we show that for any regular, analytic (and spacelike in the case of de Sitter three-space) curve ${\gamma}$ and an analytic (timelike in the case of de Sitter three-space) unit vector field N along and orthogonal to ${\gamma}$, there exists a unique (spacelike in the case of de Sitter three-space) surface of constant mean curvature 1 which contains ${\gamma}$ and the unit normal of which on ${\gamma}$ is N. Some of the consequences are the planar reflection principles, and a classification of rotationally invariant CMC 1 surfaces.

• Restorative Dentistry and Endodontics
• /
• 제44권2호
• /
• pp.19.1-19.9
• /
• 2019

Objectives: The purpose of this study was to evaluate the cyclic fatigue, bending resistance, and surface roughness of EdgeEvolve (EdgeEndo) and ProTaper Gold (Dentsply Tulsa Dental Specialties) nickel-titanium (NiTi) rotary files. Materials and Methods: The instruments (n = 15/each) were tested for cyclic fatigue in single- ($60^{\circ}$ curvature, 5-mm radius) and double-curved (coronal curvature $60^{\circ}$, 5-mm radius, and apical curvature of $30^{\circ}$ and 2-mm radius) artificial canals. The number of cycles to fracture was calculated. The bending resistance of both files were tested using a universal testing machine where the files were bent until reach $45^{\circ}$. Scanning electron microscopy and x-ray energy-dispersive spectrometric analysis were used for imaging the fractured segments, while the atomic force microscope was used to quantify the surface roughness average (Ra). Results: EdgeEvolve files exhibited higher cyclic fatigue resistance than ProTaper Gold files in single- and double-curved canals (p < 0.05) and both files were more resistant to cyclic fatigue in single-curved canals than double-curved canals (p < 0.05). EdgeEvolve files exhibited significantly more flexibility than did ProTaper Gold files (p < 0.05). Both files had approximately similar Ni and Ti contents (p > 0.05). EdgeEvolve files showed significantly lower Ra values than ProTaper Gold files (p < 0.05). Conclusions: Within the limitation of this study, EdgeEvolve files exhibited significantly higher cyclic fatigue resistance than ProTaper Gold files in both single- and double-curved canals.

• 대한토목학회논문집
• /
• 제29권5B호
• /
• pp.463-472
• /
• 2009

본 연구에서는 잠제가 설치된 연안역에서 해안의 곡률반경이 잠제 주변 파동장에 미치는 영향을 파악하기 위하여 파 구조물 해빈/해저지반의 상호작용을 해석할 수 있는 3차원 수치모델 LES-WASS-3D를 이용하여 시뮬레이션을 실시하였다. 먼저 기존의 수리모형실험결과와 비교 검토를 통하여 타당성과 유효성을 확인하였으며, 수치실험을 통해 얻어진 수치해석결과로부터 잠제 주변의 파고분포, 평균수위분포, 상층흐름분포, 평균류분포 그리고 연안에서의 처오름 높이분포를 비롯한 잠제 주변의 3차원적 수리특성에 미치는 해안곡률의 영향에 관하여 고찰하였다.

• 대한전자공학회논문지
• /
• 제27권5호
• /
• pp.757-766
• /
• 1990

In this paper a new knowledge based vision system using orientation information on each surface of the 3-dimensional object is discussed. The measurement of the orientation information is performed by photometric stereo method. And then the obtained orientations are segmented using Gaussian curvature and mean curvature. A hierarchical knowledge base which is based on the characteristics, shape, area and length of the surface is built up, and then the knowledge based system infers by the condition interprete system (CIS). As the results, an easier and more accurate 3-D object recognition system is implemented, because it uses the characteristics and shapes as units of the surface in the recognition process.

• 대한기계학회논문집
• /
• 제16권2호
• /
• pp.302-312
• /
• 1992

Three dimensional velocity measurements of a 35.deg. inclined jet issuing into turbulent boundary layer on both concave and convex surfaces have been conducted. To investigate solely the effect of each curvature on the flow field, streamwise pressure variations are minimized by adjusting the shape of the opposite wall in the curved region. From the measured velocity components, streamwise mean vorticities are calculated to determine jet-crossflow interface. The results on convex surface show that the injected jet is separated from the wall and the bound vortex maintains its structure far downstream. On concave surface, the secondary flow in the jet cross-sections are enhanced and in some downstream region from the jet exit, the flow on the concave surface has been developed to Taylor-Gortler vortices

• Tribology and Lubricants
• /
• 제17권4호
• /
• pp.276-282
• /
• 2001

Nano adhesion between SPM (scanning probe microscope) tips and 075 (octadecyltrichlorosilane) SAM (self-assembled monolayer) was experimentally studied. Tests were performed to measure the nano adhesion and friction in both AFM(atomic force microscope) and LFM(lateral force microscope) modes in various conditions of relative humidity. OTS SAM was formed on Si-wafer (100) surfaces, and Si$_3$N$_4$ tips of different radius of curvature were used. When the surface was hydrophobic, the adhesion and friction forces were found lower than those of bare Si-wafer. Results also showed that micro-adhesion force increased as the relative humidity and the tip radius of curvature increased. The main parameter for affecting the micro-adhesion was found absorbed humidity on the contact surface. These results were discussed with the JKR model and a capillary force caused by absorbed water.