• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.35 no.10
• /
• pp.1033-1040
• /
• 2011

The premixed burner is a very strong candidate for using household boiler burner system because it has high efficiency, low emission and can be used in compact boiler system. Usually, household boiler burner systems use a Bunsen burner, which consists of an inner rich premixed flame and fuel burned completely by a secondary air supply. It has a relatively long flame length and operates in a high excess of air, so it is difficult to fit such a burner into a high efficiency compact boiler. In this paper, the characteristics of a premixed combustion burner for surface media such as metal fiber, ceramic, and SUS fin were evaluated. In particular, the flow velocity over the burner surface for the cold flow characteristics of the surface material were measured and adjusted. The combustion tests were carried out by taking pictures of the flame and measuring the flame temperature. The amounts of CO and NO were measured and the characteristics of the surface burner materials, combustion chamber, and heat exchangers were evaluated for various excess air ratios and heating values.

• Journal of KSNVE
• /
• v.10 no.6
• /
• pp.991-997
• /
• 2000

The objective of this study is to examine the onset condition and the frequency characteristics of the low-frequency combustion oscillation in a surface burner. For this purpose, extensive parametric studies have been performed experimentally and the effects of size of each section, the equivalence ratio, and the entrance velocity on oscillatory behavior explored. The experimental results were discussed in comparison with the other combustors associated tilth the low-frequency combustion oscillation. The combustion mode is driven at high combustion rate by the lift of unstable flame near the lower limit of the combustible equivalence ratio. The oscillation frequency is dependent not on the burner geometry but on the equivalence ratio and the combustion load. Low-frequency combustion mode was formed to be divided into two different modes, named C1 and C2 respectively. Two modes occurred individually, simultaneously or transitionally according to the equivalence ratio and combustion load. The characteristics of low-frequency oscillation is different from each other depending on the type of combustors. The surface burner has also its own characteristics of low -frequency oscillation.

• 한국연소학회:학술대회논문집
• /
• 2004.11a
• /
• pp.187-194
• /
• 2004

The surface flames in porous ceramic burner are experimentally characterized to investigate the effects of equivalence ratio and firing rates. The results show that the surface flames are classified into green, red radiant and blue surface flame as the decrease of equivalence ratio. And each flame is maintained very stable and represents the same flame characteristics at any orientation of ceramic burner. Particularly the blue surface flame is found to be very stable at very lean equivalence ratio at 7000kcal/hr to 20000kcal/hr firing rates. And the exhausted NOx was analysed to find out which flame has lower NOx emission. The blue surface flame shows the lowest NOx emission regardless of the location of burner since it sustains very stable at lean mixture ratio.

• Journal of the Korean Society of Combustion
• /
• v.6 no.1
• /
• pp.29-35
• /
• 2001

The surface flames in porous ceramic burner are experimentally characterized to investigate the effects of equivalence ratio and firing rates. The results show that the surface flames are classified into green, red radiant and blue surface flame as decrease of equivalence ratio. And each flame is maintained very stably and shows the same flame characteristics at any orientation of ceramic burner. Particularly the blue surface flame was found to be very stable at very lean equivalence ratio at 200 to $800\;kw/m^2$ firing rates. And the exhausted NOx was analysed to find out which flame has lower NOx emission. The blue surface flame showed the lowest NOx emission regardless of the location of burner since it sustained very stable at lean mixture ratio.

• Journal of the Korean Society of Combustion
• /
• v.10 no.1
• /
• pp.7-12
• /
• 2005

The surface flames in perforated ceramic burner are experimentally characterized to investigate the effects of equivalence ratio and heating rate. The results show that the surface flames are classified into green, red radiant and blue surface flame as the decrease of equivalence ratio. Each flame is maintained very stable at the specified equivalence ratio and represents the same flame characteristics at any orientation of ceramic burner. Particularly the blue surface flame is found to be very stable at very lean equivalence ratio at 7000kcal/hr to 20000kcal/hr heating rates. And the exhausted NOx measurement shows that blue surface flame represents the lowest NOx emission regardless of the location of burner since it sustains very stable at lean mixture ratio.

• Proceedings of the Safety Management and Science Conference
• /
• 2004.11a
• /
• pp.189-195
• /
• 2004

It compared quality characteristics for the stone surface treatment system and its products. With the result, the flame burner equipment was mainly used to the surface treatment of granite, but it occurred greatly the high temperature, the rock fragment, the noise and dust. For the other side, the whetstone polishing machine for the polishing was a maintenance for the specific physical properties of stone, and it did not occur the stone fragment and the dust. The durability of the stone products due to the flame burner was investigated with that it falls to $20\sim25\%$ more than the surface treatment by the whetstone polishing. Share's hardness of the polishing products in the durability test showed more greatly index than the flame burner and conventional product. The polishing products of Pochon stone in the case of the abrasion resistance showed great more $15\%$ than the general products, more $9\%$ than the products by the flame burner.

• International Journal of Highway Engineering
• /
• v.17 no.2
• /
• pp.31-37
• /
• 2015

PURPOSES : To design a pre-heater for warm in-place recycling equipment, three different heating systems were evaluated to determine their thermal efficiency. METHODS: In this study, a $30cm{\times}30cm{\times}15cm$ wheel-tracking specimen was used to measure the inner temperature as a function of the heating system. The inner temperature of the specimen was measured with a data logger at the surface, and at depths of 1cm, 2cm, 3cm, 4cm, and 5cm. To evaluate the thermal efficiency, the researchers used three different types of equipment, namely, IR, a heating wire, and a gas burner. RESULTS: The IR heating system exhibits a higher level of performance than the others to achieve the target temperature at a depth of 5cm in the specimen. The gas burner system was capable of heating the surface to a temperature of up to $600^{\circ}C$. The other types, however, cannot heat the surface up to 600. The thermal efficiencies were measured based on the laboratory conditions. CONCLUSIONS: To find the most effective system for application to the development of a pre-heater for warm in-place recycling, various systems (IR, heating wire, gas burner) were examined in the laboratory. As a result, it was found that the hot plate of a gas burner system provides the highest temperature at the surface of the asphalt but, of all the systems, the IR system provides the best internal temperature increase rate. Furthermore, a gas burner can age the asphalt binder of the surface layer as a result of the high temperature. However, the gas burner cannot attain the target temperature at 5cm. The IR system, on the other hand, is effective at increasing the internal temperature of asphalt.

• Proceedings of the KSME Conference
• /
• 2007.05b
• /
• pp.2154-2159
• /
• 2007

The potential of using a double-faced wall stagnation flow burner in mass production of carbon nanotubes was evaluated experimentally and computationally. With nitrogen-diluted premixed ethylene-air flames established on the Nickel-coated stainless steel double-faced wall, the propensities of carbon nanotube formation were experimentally determined using SEM and FE-TEM images and Raman spectroscopy, while the flame structure was computationally predicted using a 3-dimensional CFD code with a reduced reaction mechanism. The uniformity and yields of synthesized carbon nanotubes were evaluated in terms of the flame stretch rates. Results show substantial increase of area on the wall surface where uniform carbon nanotubes are synthesized with using the double-faced wall stagnation flow burner due to enhanced uniformity of temperature distribution along the wall surface and support the potential of using a double-faced wall stagnation flow burner in mass production of carbon nanotubes.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.9 no.2
• /
• pp.221-228
• /
• 1997

A strong combustion-driven sound from a surface burner made of a perforated metal fiber plate for premixed gas was investigated to clarify the physical mechanism of its generation. A simple model was developed for the acoustic power generation in terms of the heat transfer response function and the acoustic impedance of the burner. The acoustic impedance of the perforated metal fiber placed on the open exit was measured and the heat release response of the burner to the oscillating flow associated with the acoustic disturbance was expressed in terms of a response function. It was found that the power is generated by the heat release in response to the downstream particle velocity, in contrast to the upstream velocity in the case of the Rijke oscillation driven by a heater placed in the lower half of a columm with upstream flow. The measured frequencies of the oscillation were in agreement with the estimated resonance frequencies and their excitation was varied with the combustion conditions. For the same fuel rate, the excited frequency increases with the air ratio if it is low but decreases with the ratio if not so low. Such frequency characteristics were explained by assuming a heat release response function with a time constant and it was shown that the excited frequency decreases as the time constant increases.

• Journal of the Korean Society of Combustion
• /
• v.15 no.3
• /
• pp.8-14
• /
• 2010

Fuel processing systems which convert fuel into rich gas (such as stream reforming, partial oxidation, autothermal reforming) need high temperature environment ($600{\sim}1,000^{\circ}$). Generally, anode-off gas or mixture of anode-off gas and LNG is used as input gas of fuel reformer. In order to make efficient and low emission burner system for fuel reformer, it is necessary to elucidate the combustion and emission characteristic of fuel reformer burner. The purpose of this study is to develop a porous premixed flat ceramic burner that can be used for 1~5 kW fuel cell reformer. Ceramic burner experiments using natural gas, hydrogen gas, anode off gas, mixture of natural gas & anode off gas were carried out respectively to investigate the flame characteristics by heating capacity and equivalence ratio. Results show that the stable flat flames can be established for natural gas, hydrogen gas, anode off gas and mixture of natural gas & anode off gas as reformer fuel in the porous ceramic burner. For all of fuels, their burning velocities become smaller as the equivalence ratio goes to the lean mixture ratio, and a lift-off occurs at lean limit. Flame length in hydrogen and anode off gas became longer with increasing the heat capacity. In particular, the blue surface flame is found to be very stable at a very lean equivalence ratio at heat capacity and different fuels. The exhausted NOx and CO measurement shows that the blue surface flame represents the lowest NOx and CO emissions since it remains very stable at a lean equivalence ratio.