• Journal of the Ergonomics Society of Korea
• /
• 제14권1호
• /
• pp.37-57
• /
• 1995

The purpose of this study was to investigate the elastic effect of deformation and restriction in wearing a support type panty stocking (PS). The study investigated deformation rate in all surface area, deformation rate in local area, length deformation rate, changes in slip and feeling of restriction under the standard laboratory condition. Two healthy adult females in twenties wore four types of PS. The result were as follows : The deformation rate in all surface area was 117 .approx. 132% in wearing support type PS, 157% in wearing mono type PS, due to the intensities of restriction. The deformation rate in local area was in order, course > oblique > wale direction. The largest deformation rate was observed in hip girth. Between the deformation rates in all surface and local areas was a high correlation acknowledged, especially the course direction showed a high correlation. Support type PSs showed more deformation and changes of slip than wool and mono type PS. Especially, changes of slip at the knee appeared greatly. The responses of restriction evaluated from a paired comparison method were in order, JS 2 > KS 4 > KS 9 > KS 5 > KS 1 > KM 3.

• Korean Journal of Remote Sensing
• /
• 제34권1호
• /
• pp.101-115
• /
• 2018

The Long Valley area and its surroundings are part of a major volcano system where inflation occurred in the resurgent dome in the 1990s. We used ENVISAT data to monitor surface deformation of the Long Valley area and its surroundings after the inflation, from 2003-2010. To retrieve the time series of the deformation, we applied the refined Small BAseline Subset (SBAS) algorithm which is improved using an iterative approach to minimize unwrapping error. Moreover, ascending and descending data were used to decompose the horizontal and vertical deformation in detail. To confirm refined SBAS results, we used GPS dataset. The InSAR errors are estimated as ${\pm}1.0mm/yr$ and ${\pm}0.8mm/yr$ from ascending and descending tracks, respectively. Compare to the previous study of 1990s over the Long Valley and its surroundings, Paoha Island and CASA geothermal area still subside. The deformation pattern in the Long Valley area during the study period (2003-2010) went through both subsidence (2003-2007) and slow uplift(2007-2010) episodes. Our research also shows no deformation signal near McGee Creek. Our study provided a better understanding of the surface changes of the indicators in the 1990s and 2000s.

• Journal of Biosystems Engineering
• /
• 제26권5호
• /
• pp.409-414
• /
• 2001

This paper reports a technique for measuring a three-dimensional soil deformation and a simplified method to determine the three-dimensional contact area of agricultural tires in a soil bin. A Pirelli 12.4R28 radial-ply tire was used on soft soil. Effects of dynamic load and inflation pressure were determined using the equipment for measuring soil deformation on the soil surface. Soil deformation measurements were made under three conditions of over-load (59kPa-14.2kN), rated-load (108kPa-11.8kN) and under-load (157kPa-9.3kN) in the combinations of the inflation pressures (kPa) and the tire load (kN). The results from three conditions were shown that the contact area of the over-load increased considerably bigger than those of the rated-load and the under-load. Therefore, to regulate soil deformation, the inflation pressure and the tire load should be set according to the soil conditions.

• 한국지구물리탐사학회:학술대회논문집
• /
• 한국지구물리탐사학회 2003년도 Proceedings of the international symposium on the fusion technology
• /
• pp.305-312
• /
• 2003

Remote sensing can provide invisible information in addition to acquire wide-view image data from space. Synthetic Aperture Radar (SAR) transmits microwave to the earth from a satellite and collects the reflected echo from the surface. Interferometric processing of SAR data can detect the subtle land deformation. The information of the surface movement by SAR is useful to monitor the volcanic activity, extended subsidence of urbanized area and the prediction of the earthquake caused by crustal deformation, and it complements the conventional levelling and GPS technique. PSInSAR (Permanent Scatterers Interferometric SAR) is one of interferometric techniques to be applied to practical projects in Japan. In this paper, the projects of land deformation monitoring are shown after the explanations of the PSInSAR principle. Tokai earthquake risk assessment is the first example. PSInSAR detects the subduction of crustal deformation of the adjacent area of new assumed epicenter region of the Tokai Earthquake. The extended subsidence of the urbanized area was implemented by using Japanese satellite data i.e. JERS that has so much data the surrounding of Japan as the archive. We examine the relationship between the geological structure and settlement at Nohbi basin including Nagoya city.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 한국공작기계학회 1999년도 추계학술대회 논문집 - 한국공작기계학회
• /
• pp.251-256
• /
• 1999

"Ploughing" on the flank face of the tool in the metal cutting process is due to the tool in the metal cutting process is due to the finite edge radius of the tool and due to the development of flank wear. Because of the high stresses near the cutting edge, elastic-plastic deformation would be caused between the tool and the machined surface over a small area of the tool flank. The deformation would affect the roughness of the machined surface. Recently, some attempts have been made to predict the surface roughness, but elastic-plastic effect due to ploughing in the cutting process has not been considered. The research has analyzed mechanism of the ploughing of the cutting process using contact mechanics. Tool and workpiece material properties have been taken into account in the prediction of the surface roughness. The surface roughness has been simulated by the surface-shaping system. The results between experiment and simulation have been compared and analyzed. analyzed.

• Journal of Welding and Joining
• /
• 제26권2호
• /
• pp.62-68
• /
• 2008

Effects of gravitational orientation on gas tungsten arc welding (GTAW) for 304 stainless steel were studied to determine the critical factors for weld pool formation, such as weld surface deformation and weld pool shape. This study was accomplished through an analytical study of weld pool stability as a function of primary welding parameters (arc current and arc holding time), material properties (surface tension and density), and melting efficiency (cross-sectional area). The stability of weld pool shape and weld surface deformation was confirmed experimentally by changing the welding position. The arc current and translational velocity were the major factors in determining the weld pool stability as a function of the gravitational orientation. A 200A spot GTAW showed a significant variation of the weld pool formation as the arc held longer than 3 seconds, however the weld pool shape and surface morphology for a 165A spot GTAW were 'stable', i.e., constant regardless of the gravitational orientation. The cross-sectional area of the weld (CSA) was one of the critical factors in determining the weld pool stability. The measured CSA ($13.5mm^2$) for the 200A spot GTAW showed a good agreement with the calculated CSA ($14.9mm^2$).

• Proceedings of the Korean Society of Surveying, Geodesy, Photogrammetry, and Cartography Conference
• /
• 한국측량학회 2003년도 추계학술발표회 논문집
• /
• pp.135-140
• /
• 2003

This study try to surface deformation analyzing and 3-D monitoring of hydro structure by close-range photogrammetry technique using 35mm metric camera. For this, the lens distortion parameters were acquired for 21mm super-wide-angle lens which is mounted in 35mm metric camera. After that, the system designed for absolute deformation analysis of object surface, and examined the application validity Also, optimum photographing condition was derived by calculated the standard deviation of this system. This system can monitor periodically changing of surface area, volume and deformation precisely after placed plate underwater. Finally, this paper suggested efficiency of absolute deformation analysis by using small format camera.

• Proceedings of the KSRS Conference
• /
• 대한원격탐사학회 2008년도 International Symposium on Remote Sensing
• /
• pp.49-52
• /
• 2008

New Orleans located in the estuary of the Mississippi River was attacked by Hurricane Katrina and suffered big flood on August 2005. Since unconsolidated Holocene to middle Miocene strata is the main basement rocks, land subsidence has been occurred steadily due to soil compaction and normal faulting. It was reported that the maximum subsidence rate from 2002 to 2005 was -29 mm/yr. Many studies in the area have been carried out for understanding the subsiding and potential risks caused by ground subsidence are weighted by the fact that a large area of the city is located below the mean sea level. A small baseline subset (SBAS) method is applied for effectively measuring time-series LOS (Line-of sight) surface deformation from differential synthetic aperture radar interferograms in this study. The time-series surface deformation at New Orleans was measured from RADARSAT-1 SAR images. The used dataset consists of twenty-one RADARSAT-1 fine beam mode images on descending orbits from February 2005 to February 2007 and another twenty-one RADARSAT-1 standard beam mode images on ascending orbits from January 2005 to February 2007. From this dataset, 25 and 38 differential interferograms on descending and ascending orbits were constructed, respectively. The vertical and horizontal components of surface deformation were extracted from ascending and descending LOS surface deformations. The result from vertical component of surface deformation indicates that subsidence is not significant with a mean rate of -3.1${\pm}$3.2 mm/yr.

• Korean Journal of Remote Sensing
• /
• 제30권6호
• /
• pp.719-730
• /
• 2014

Small BAseline Subset (SBAS) technique using multi master interferograms can be effective to detect surface deformation in forest area. In this paper, The analysis reveals area of 2-dimension surface deformation at Seguam Island in Aleutian Arc., Alaska. We acquired ERS-1/2 data from track 201 and 473 datasets on Seguam Island from 1992 to 2008. This study analyze surface deformation applying Differential Interferometry Synthetic Aperture Radar (DInSAR) and SBAS time series method using two adjacent tracks. As a results, it was calculated that subsidence -1~2 cm in LOS direction and - 2~3 cm in vertical direction. The horizontal direction was repeated contraction and expansion. The observation of 2-dimension displacements explained the volcanic activity on Seguam island. Also, it is believed to be used for basic data to estimate movements of magma source.

• Transactions of Materials Processing
• /
• 제14권4호
• /
• pp.375-383
• /
• 2005

The shear spinning process, where the plastic deformation zone is localized in a very small portion of the workpiece, shows a promise for increasingly broader application to the production of axially symmetric parts. In this paper, the three components of the working force are calculated by a newly proposed deformation model in which the spinning process is understood as shearing deformation after uniaxial yielding by bending, and shear stress, $\tau_{rz}$, becomes k, yield limit in pure shear, in the deformation zone. The tangential force are first calculated and the feed force and the normal force are obtained by the assumption of uniform distribution of roller pressure on the contact surface. The optimum contact area is obtained by minimizing the bending energy required to get the assumed deformation of the blank. The calculated forces are compared with experimental results. A comparison shows that theoretical prediction is reasonably in good agreement with experimental results