• Transactions on Electrical and Electronic Materials
• /
• 제10권3호
• /
• pp.75-79
• /
• 2009

An intrinsic silicon thin film passivation layer is deposited by the microwave remote-plasma enhanced chemical vapor deposition at temperature of $175^{\circ}C$ and various gas ratios for solar cell applications. The good quality amorphous silicon films were formed at silane $(SiH_4)$ gas flow rates above 15 seem. The highest effective carrier lifetime was obtained at the $SiH_4$, flow rate of 20 seem and the value was about 3 times higher compared with the bulk lifetime of 5.6 ${\mu}s$ at a fixed injection level of ${\Delta}n\;=\;5{\times}10^{14}\;cm^{-3}$. An annealing treatment was performed and the carrier life times were increased approximately 5 times compared with the bulk lifetime. The optimal annealing temperature and time were obtained at 250 $^{\circ}C$ and 60 sec respectively. This indicates that the combination of the deposition of an amorphous thin film at a low temperature and the annealing treatment contributes to the excellent surface and bulk passivation.

• 한국수소및신에너지학회논문집
• /
• 제33권1호
• /
• pp.113-120
• /
• 2022

Quantum dots (QDs) are attractive photosensitizer candidates for application not only in solar cells but also in solar hydrogen generation. For the prepartion of highly efficient QD-sensitized photoelectrodes, it is important to reduce electron recombination at the photoanode/electrolyte interface. Here, we study on the coating condition of ZnS passivation layers on the photoanodes in QD-sensitized solar cells (QDSCs). The ZnS passivation layers are coated by successive ionic layer adsorption and reaction method, and as the cation precursor, zinc acetate and zinc nitrate are empolyed. Due to the higher pH of cation precursor solution, the ZnS loading is improved when the zinc acetate is used, compared to the zinc nitrate. This improved loading of ZnS leads to the reduced electron recombination at the surface of photoanodes and the enhaced conversion efficiency of QDSCs from 6.07% to 7.45%.

• Corrosion Science and Technology
• /
• 제7권2호
• /
• pp.119-124
• /
• 2008

Steel is generally not corrosion resistant to water with formation of non protective rusts on its surface. Rusts are composed of iron oxides such as $Fe_3O_4$, $\alpha-$, $\beta-$, $\gamma-$and ${\delta}-FeOOH$. However, steel, particularly weathering steel containing small amounts of Cu, Ni and Cr etc., shows good corrosion resistance against rural, industrial or marine environment. Its corrosion rate is exceedingly small as compared with that of carbon steel. According to the exposure test results undertaken in outdoor environments, the atmospheric corrosion rate for weathering steel is only 1 mm for a century. Atmospheric corrosion for steels proceeds under alternate dry and wet conditions. Dry condition is encountered on steel surface on fine or cloudy days, and wet condition is on rainy or snowy days. The reason why weathering steel shows superior atmospheric corrosion resistance is due to formation of corrosion protective rusts on its surface under very thin water layer. The protective rusts are usually composed of two layer rusts; the upper layer is ${\gamma}-FeOOH$ termed as lepidocrocite, and inner layer is nano-particle ${\alpha}-FeOOH$ termed as goethite. This paper is aimed at elucidating the atmospheric corrosion mechanism for steel in comparison with corrosion in bulky water environment by use of empirical data.The summary is as follows: 1. No corrosion protective rusts are formed on steel in bulky water. 2. Atmospheric corrosion for steel is the corrosion under wetting and drying conditions. Corrosion and passivation occur alternately on steel surface. Steel, particularly weathering steel with small amounts of alloying elements such as Cu, Ni and Cr etc. enhances forming corrosion protective rusts by passivation.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2016년도 제50회 동계 정기학술대회 초록집
• /
• pp.237.1-237.1
• /
• 2016

Electrical properties of graphene-based field effect transistors (G-FETs) can be degraded in ambient conditions owing to physisorbed oxygen or water molecules on the graphene surface. Passivation technique is one of a fascinating strategy for fabrication of G-FETs, which allows to sustain electrical properties of graphene in the long term without disrupting its inherent properties: transparency, flexibility and thinness. Ironically, despite its importance in producing high performance graphene devices, this method has been much less studied compared to patterning or device fabrication processes. Here we report a novel surface passivation method by using atomically thin self-assembled alkane layers such as C18- NH2, C18-Br and C36 to prevent unintentional doping effects that can suppress the degradation of electrical properties. In each passivated device, we observe a shift in charge neutral point to near zero gate voltage and it maintains the device performance for 1 year. In addition, the fabricated PG-FETs on a plastic substrate with ion-gel gate dielectrics exhibit not only mechanical flexibility but also long-term stability in ambient conditions. Therefore, we believe that these highly transparent and ultra-thin passivation layers can become a promising candidate in a wide range of graphene based electronic applications.

• 한국표면공학회지
• /
• 제50권3호
• /
• pp.219-224
• /
• 2017

The K gettering in $SiO_2/PSG/SiO_2/Al-1%Si$ multilevel thin films was investigated using SIMS(secondary ion mass spectrometry) and XPS(X-ray Photoelectron Spectroscopy) analysis. DC magnetron sputter techniques and APCVD(atmosphere pressure chemical vapor deposition) were utilized for the deposition of Al-1%Si thin films and $SiO_2/PSG/SiO_2$ passivations, respectively. Heat treatment was carried out at $400^{\circ}C$ for 5 h in air. SIMS depth profiling was used to determine the distribution of K, Al, Si, P and other elements throughout the $SiO_2/PSG/SiO_2/Al-1%Si$ multilevel thin films. XPS was used to analyze binding energies of Si and P elements in PSG passivation layers. K peaks were observed throughout the $PSG/SiO_2$ passivation layers on the Al-1%Si thin films and especially at the $PSG/SiO_2$ interfaces. K gettering in $SiO_2/PSG/SiO_2/Al-1%Si$ multilevel thin films is considered to be caused by a segregation type of gettering. The chemical state of Si and P elements in PSG passivation appears to be $SiO_2$ and $P_2O_5$, respectively

• Current Photovoltaic Research
• /
• 제11권3호
• /
• pp.87-95
• /
• 2023

As the demand for the Internet of Things grows, research into indoor photovoltaics for wireless power is becoming important. In particular, perovskite has attracted considerable attention due to its superior performance compared to other candidates. However, various surface defects present in perovskite are a limiting factor for high performance. In particular, deep-level surface defects caused by uncoordinated Pb²⁺ ions directly limit charge transport. In low light environments, this appears to be a more significant hurdle. In this study, ethylenediamine, which can provide covalent bonding to uncoordinated Pb²⁺ ions through nitrogen, was used as a surface treatment material for indoor photovoltaics. X-ray photoelectron spectroscopy confirmed that the uncoordinated Pb²⁺ ions were effectively passivated by the terminal nitrogen of ethylenediamine. As a consequence, a V_OC of 0.998 V, a JSC of 0.139 mA cm^-2 and a fill factor of 83.03% were achieved, resulting in an indoor photoelectric conversion efficiency of 38.02%.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2012년도 제43회 하계 정기 학술대회 초록집
• /
• pp.87-87
• /
• 2012

결정질 실리콘 태양전지의 효율을 향상시키기 위하여, 현재 가장 대표적으로 selective emitter가 적용되고 있다. 또한, 효율 향상을 위해 도금, 잉크젯 프린팅, 개선된 스크린 프린팅, 전사를 이용한 전극 형성 개선과 절연막을 이용한 surface passivation이 가장 활발하게 연구 되고 있다. 이외에도 연구되어지고 있는 반도체 기술의 이온주입, 플라즈마 도핑기술 등이 있다. 효율 향상과 관련된 기술들을 논할 것이며, 특히 원자층증착법(ALD)을 이용하여 surface passivation의 특성 향상과 양산 기술 적용 그에 따른 전극 형성 구조에 대하여 발표하고자 한다. ALD기술은 표면반응증착이기 때문에 실리콘 세정법에 따라 패시베이션 특성이 달라지게 된다. 세정법과 열처리에 따른 Al2O3박막의 물성변화, 계면의 반응에 따라서 전하 수명 값이 크게 좌우되는 것을 제시할 것이다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2001년도 하계학술대회 논문집 C
• /
• pp.1369-1371
• /
• 2001

This paper describes on thinning SDB SOI substrates by SDB technology and Electro-chemical etch-stop. The surface of the fabricated SDB SOI substrates is more uniform than that grinding or polishing by mechanical method, and this process is possible to accurate SOI thickness control. During Electrochemical etch-stop, leakage current versus voltage curves were measured for analysis of the open current potential (OCP) point and the passivation potential (PP) poin and determinated to anodic passivation potential. The surface roughness and selectively controlled thickness of the fabricated SOI substrates were analyzed by using AFM and SEM, respectively.

• Journal of Magnetics
• /
• 제22권1호
• /
• pp.100-103
• /
• 2017

We studied the microstructure and magnetic properties of Fe nanosized powder synthesized by the pulsed wire evaporation method. The x-ray diffraction spectrum confirmed that this powder had a pure ${\alpha}$-Fe phase. Scanning electron microscope and transmission electron microscope measurements indicated that the prepared powder had uniform spherical shape with core-shell structure. The mean powder size was about 35 nm and the thickness of the surface passivation layer was about 5 nm. Energy dispersive X-ray spectroscopy measurement indicated that the surface passivation layer was iron oxide. Magnetic field dependent magnetization measurement at room temperature showed that the maximum magnetization of the prepared powder was 177.1 emu/g at 1 T.

• 세라미스트
• /
• 제21권1호
• /
• pp.24-43
• /
• 2018

Organic-inorganic halide perovskite materials have attracted significant attention during the last few years because of their superior properties for electronic and optoelectronic devices, such as their long charge carrier diffusion lengths and high photoluminescence quantum yields of up to 100% with tunable bandgaps over the entire visible spectral range. In addition to solar cells, light emitting diodes (LEDs) represent a fascinating application for halide perovskite materials. In this study, we review the recent progress in halide perovskite LEDs. The current strategies for improving the performance of halide LEDs, focusing on morphological engineering, dimensional engineering, compositional engineering, surface passivation, interfacial engineering, and the plasmonic effect are discussed. The challenges and perspectives for the future development of halide perovskite LEDs are also considered.