• Korean Journal of Optics and Photonics
• /
• v.34 no.6
• /
• pp.276-282
• /
• 2023

In this paper, we designed a lighting optical system using a freeform lens as a substitute for expensive gobo lighting. Unlike gobo lighting, freeform lens lighting does not use an image mask, and it can form and project an image directly on the lens surface using only a single lens, thus reducing the cost compared to gobo lighting. In order to verify the performance of freeform lens lighting with these advantages, we conducted an illuminance simulation. As a result, it was confirmed that it can replace gobo lighting because it has an illuminance distribution similar to the image we want to irradiate and a light efficiency of 47% similar to the performance of gobo lighting.

• KIEAE Journal
• /
• v.7 no.6
• /
• pp.29-36
• /
• 2007

Recently, rapid development of technique and change of lifestyle during nighttime has activated the urban outdoor lighting and renovated consideration of nightscape. As the interest of nightscape increases more widely, outdoor lighting has been installed more and more in the cities. Nightscape comes in diverse forms. So, there is no absolute standard for outdoor lighting. But only bright outdoor lighting is not necessarily a good nightscape. Installation lighting without master plan or excessive outdoor lighting may cause a inharmony. This study aims to analyze the luminous characteristics of facade in shopping complexes. For the purpose, four large-scale shopping complexes located in Dongdaemun area were selected. Building facade composition, outdoor lighting composition, and lighting equipment of each shopping complexes are surveyed, and luminance of building facade were measured with Prometric 1400. The result of the study are as follows; (1) Horizontally large-scale shopping complexes emphasize the building entrance and shape of the building at night by outdoor lighting. (2) Non cut-off luminaries installed in building entrance and shop front caused the potential of light pollution.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.26 no.12
• /
• pp.915-919
• /
• 2013

This is the study on the development of fusion heat dissipation of carbon magnesium materials. The purpose of this study is for effective utilization of heat emission which is the core of LED lighting. The result of study enabled the derivation of side satisfying result of making the surface temperature of lighting to be below $70^{\circ}C$ (actual measurement: $58^{\circ}C$) using magnesium. The lighting products that use magnesium was made possible based on the result of this study. Also from the performance aspect such as light distribution, the measurement of light efficiency demonstrated the level of 90 lm/W. Therefore the commercialization of lighting was made possible and the efficiency could be further enhanced by supplementation of LED performance.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.25 no.12
• /
• pp.27-33
• /
• 2011

This study aims to suggest some problems, which occur when environmental lighting zone is set by use-zone only, by comparing and analyzing the artificial illumination luminance. In addition, this study aims to review the control standards of light pollution and to suggest a practical environmental lighting zone-setting method. I checked out the standards of average surface luminance and luminance contrast as for light pollution management. In addition, I did some research on evaluation of light pollution on surroundings based on investigation of use-environment as for lighting environment setting method.

• 한국태양에너지학회:학술대회논문집
• /
• 2011.04a
• /
• pp.168-173
• /
• 2011

Recently, from a saving energy and environmental lighting sources point of view, using LED lighting have been increased rapidly. The colors of light was applied to the control of dimmers that is composed of red, green, blue, and white(RGBW) to improve the quality of visual environment. Moreover this study has been processed to develop adjustable dynamic LED lighting system on SPD and definitize the various spectral power distribution and color temperature of light through the control of the four dimmers. It is possible to combine up to $432^4$ kinds of light. Measurement of illuminance of range on working surface was as 7~l,831 lux. Application of visual environment for occupants can be expected according to control of lighting performance.

• KIEAE Journal
• /
• v.13 no.2
• /
• pp.47-52
• /
• 2013

The problems of light pollution first became an issue in the 1970s when astronomers identified the degradation of the night sky due to the increase in lighting associated with development and growth. As more impacts to the environment by lighting have been identified, many attempts have been made for reducing light pollutions. To prevent light pollution and increase energy efficiency, Seoul Metropolitan Government(SMG) replaced metal halide road lighting to LED luminaire in four arterial highway in Seoul. The present study compared the lighting characteristics of metal halide and LED luminaire in terms of Korea Standard for road lighting(KS A 3701) and BUG rating from Illuminating Engineering Society of North America(IESNA). The results showed that LED luminaire increased road surface luminance up to 2 times in average compared to the metal halide environment. Also, LED luminaire reduced the glare value by 2 times and luminous flux over 50% than the metal halide luminaire. In comparison with the BUG ratings, LED luminaire rated 1 degree lower for the backlight ratings and 3-4 degrees lower for the uplight ratings. The measured values testified that the LED luminaire is effective for roadway lighting and light pollution reduction.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.27 no.9
• /
• pp.23-35
• /
• 2013

In this study, we collected the emotion vocabulary novel related to the LED system light emotion and the existing terms through previous research, targeting professionals and KJ method, we selected emotion term of 35 kinds. Targeting this east Foreigner, we compared the emotion evaluation by changing the lighting elements in accordance office, meeting room, lounge, the OA room different behavior patterns. The results, showing the difference between the results of emotion existing research generally derived factors three axes "future, functionality" See, "stability", "activity". As a result of the comparison of the emotion of the East and the West, the Oriental, functional aspects of the LED system light of space office, meeting room, lounge is drawn most, On the other hand, Westerners, come up, stable surface shows the difference in accidentally. Based on these results, the future, and tries to utilized to evaluate the emotion reaction of the illumination elements each Test-Bed actual.

• Journal of KIISE:Software and Applications
• /
• v.37 no.2
• /
• pp.104-109
• /
• 2010

The lighting reflection is a common problem in image analysis and causes the many difficulties to extract distinct features in related fields. Furthermore, the problem grows in the rainy night. In this paper, we aim to remove light reflection effects and reconstruct a road surface without lighting reflections in order to extract distinct features. The proposed method utilizes a 3D analysis based on a multiple geometry using captured images, with which we can combine each reflected areas; that is, we can remove lighting reflection effects and reconstruct the surface. At first, the regions of lighting sources and reflected surfaces are extracted by local maxima based on vertically projected intensity-histograms. After that, a fundamental matrix and homography matrix among multiple images are calculated by corresponding points in each image. Finally, we combine each surface by selecting minimum value among multiple images and replace it on a target image. The proposed method can reduces lighting reflection effects and the property on the surface is not lost. While the experimental results with collected data shows plausible performance comparing to the speed, reflection-overlapping areas which can not be reconstructed remain in the result. In order to solve this problem, a new reflection model needs to be constructed.

• The Transactions of the Korean Institute of Electrical Engineers D
• /
• v.51 no.11
• /
• pp.514-520
• /
• 2002

n industrial computer vision systems, the image quality is dependent on the parameters such as light source, illumination method, optics, and surface properties. Most of them are related with the lighting system, which is designed in heuristic based on the designer's experimental knowledge. In this paper, a design code by which the optimal lighting method and light source for computer vision systems can be found are suggested based on experimental results. The design coed is applied to the design of the lighting system for the transistor marking inspection system, and the overall performance of the machine vision system with the lighting system show the effectiveness of the proposed design code.

• Journal of the Korean Solar Energy Society
• /
• v.24 no.4
• /
• pp.35-43
• /
• 2004

Illuminance and luminous levels in a small office space due to daylight were calculated to analyze the impact of daylight on contrast and lighting energy savings. Computer simulations were performed for four blind conditions under a clear sky condition. The blind conditions significantly impacted the illuminance an4 luminance level. Visual performance scores were calculated according to the transfer function that uses absolute contrast between target and background surface. The blind condition that had 45 tilted angle toward ground provided good contrast and performance scores. Using a control algorithm of an automated daylight dimming control system lighting energy sayings were predicted. For all blind conditions minimum lighting energy was consumed.