• 터널과지하공간
• /
• 제25권6호
• /
• pp.527-533
• /
• 2015

본 연구에서는 고정익 무인항공기(드론, SenseFly eBee)를 이용하여 국내 대규모 석회석 노천광산에 대한 지형측량을 수행하였다. 비행고도 300 m, 비행속도 12 m/s 조건으로 약 30분간 자동모드 비행을 수행한 결과 현장에서 총 288장의 항공사진을 촬영할 수 있었다. 특이점 추출이 불가능한 37장의 항공사진을 제외한 251장의 항공사진 자료들을 보정하고, 정합한 결과 7 cm 해상도의 정사영상과 수치표면모델 자료를 생성할 수 있었다. 4곳의 지상기준점에 대하여 고정밀 위성측정시스템를 이용하여 측정한 위치 좌표와 고정익 무인항공기 사진측량시스템을 이용하여 추출한 위치 좌표를 비교한 결과 평균 제곱근 오차가 15 cm 내외로 분석되었다. 고정익 무인항공기는 회전익 무인항공기에 비해 상대적으로 비행시간이 길어 넓은 영역의 신속한 지형측량이 가능하므로 대규모 노천광산 현장에서 효과적으로 활용될 수 있을 것이다.

• 대한원격탐사학회:학술대회논문집
• /
• 대한원격탐사학회 2007년도 Proceedings of ISRS 2007
• /
• pp.556-559
• /
• 2007

The Urban Environmental Quality (UEQ) indicates a complex and various parameters resulting from both human and natural factors in an urban area. Vegetation, climate, air quality, and the urban infrastructure may interact to produce effects in an urban area. There are relationships among air pollution, vegetation, and degrading environmental the urban heat island (UHI) effect. This study investigates the application of multi-spectral remote sensing data from the Landsat ETM and TM sensors for the mapping of air quality and UHI intensity in Seoul from 2000 to 2006 in fine resolution (30m) using the emissivity-fusion method. The Haze Optimized Transform (HOT) correction approach has been adopted for atmospheric correction on all bands except thermal band. The general UHI values (${\Delta}(T_{urban}-T_{rural})$) are 8.45 (2000), 9.14 (2001), 8.61 (2002), and $8.41^{\circ}C$ (2006), respectively. Although the UHI values are similar during these years, the spatial coverage of "hot" surface temperature (>$24^{\circ}C$) significantly increased from 2000 to 2006 due to the rapid urban development. Furthermore, high correlations between vegetation index and land surface temperature were achieved with a correlation coefficients of 0.85 (2000), 0.81 (2001), 0.84(2002), and 0.89 (2006), respectively. Air quality is shown to be an important factor in the spatial variation of UEQ. Based on the quantifiable fine resolution satellite image parameters, UEQ can promote the understanding of the complex and dynamic factors controlling urban environment.

• 대한원격탐사학회지
• /
• 제27권3호
• /
• pp.339-351
• /
• 2011

This study investigates the potentials of satellite, ground measurement data, and geo-spatial information within an urban area for the mapping of the Urban Environmental Quality (UEQ) parameters. The UEQ indicates a complex and various parameters resulting from both human and natural factors, which are greenness, climate, air pollution, the urban infrastructure, and etc. Multi-spectral remote sensing data from the Landsat ETM and TM sensors for the mapping of air pollution by the Haze Optimized Transform (HOT) technique, Urban Heat Island (UHO using the emissivity-fusion method in Seoul from 2000 to 2006 in fine resolution (30m) were analyzed for the estimation of UEQ index. Although the UHI values are similar ($8.4^{\circ}C{\sim}9.1^{\circ}C$) during these years, the spatial coverage of "hot" surface temperature (> $24^{\circ}C$) significantly increased from 2000 to 2006 due to the rapid urban development. Furthermore, high correlations between vegetation index and land surface temperature were achieved with a correlation coefficients of 0.85 (2000), 0.81 (2001), 0.84 (2002), and 0.89 (2006), respectively. It was found that the proposed method was successfully analyzed spatial structure of the UEQ and the scenarios of the best and worst areas within the city were also identified. Based on the quantifiable fine resolution satellite image parameters, UEQ can promote the understanding of the complex and dynamic factors controlling urban environment.

• 상하수도학회지
• /
• 제31권5호
• /
• pp.397-407
• /
• 2017

A dimensionally stable anode based on the $RuO_2$ electrocatalyst is an important electrode for generating chlorine. The $RuO_2$ is well-known as an electrode material with high electrocatalytic performance and stability. In this study, sonoelectrodeposition is proposed to synthesize the $RuO_2$ electrodes. The electrode obtained by this novel process shows better electrocatalytic properties and stability for generating chlorine compared to the conventional one. The high roughness and outer surface area of the $RuO_2$ electrode from a new fabrication process leads to increase in the chlorine generation rate. This enhanced performance is attributed to the accelerated mass transport rate of the chloride ions from electrolyte to electrode surface. In addition, the electrode with sonodeposition method showed higher stability than the conventional one, which might be explained by the mass coverage enhancement. The effect of sonodeposition time was also investigated, and the electrode with longer deposition time showed higher electrocatalytic performance and stability.

• 한국자기학회지
• /
• 제22권1호
• /
• pp.6-10
• /
• 2012

본 연구에서는 인산 용액 하에서 2차 양극 산화 기법에 의해 제작된 양극 산화 알루미나 기판 상에 최대 13 nm 두께의 얇은 니켈 박막을 증착하며 증착 시 박막 두께에 따라 감소하는 박막의 저항 변화를 살펴보았다. 양극 산화 알루미나 막 표면에 존재하는 미세 기공 구조를 따라 증착된 니켈 박막 역시 다공 구조의 박막으로 성장하게 되며 증착된 박막의 두께 범위 내에서 박막의 저항은 $150k{\Omega}$ 이상의 값을 보이면서 박막 두께에 따른 저항의 감소가 매우 천천히 일어나는 것을 확인할 수 있었다. 측정된 저항 값은 기존에 보고된 균일한 기판 상에 증착된 동일 두께의 니켈 박막에 비해 매우 큼을 볼 수 있었으며 기판 표면에 존재하는 기공 구조에 의해 핵자가 형성될 수 있는 표면 면적 비가 박막 성장을 설명하는 스미기(percolation) 현상이론에서 예측하는 임계 값보다 매우 적어 미세 기공에 의해 박막의 성장과 함께 나타나는 전자 전도 채널의 형성이 저해됨으로 이해될 수 있다. 이와 함께 기존의 박막 두께에 따른 비저항 모델과 비교해 보았을 때 미세 기공의 경계에서 나타나는 전자 산란 현상 역시 박막저항의 증가에 기여함을 알 수 있다.

• 동력기계공학회지
• /
• 제20권5호
• /
• pp.46-51
• /
• 2016

The TMCP steel has expanded in the marine structure during manufacturing process because of its excellent weld-ability and impact toughness. In the case of merchant ships, coverage of TMCP steel has been used widely on over DH36 Classifications material. The line heating process is applied to the outer surface of the steel plate for the shipbuilding. In this study, We compared between TMCP and normalizing steel for shipbuilding by analyzing some basic data through performing the natural cooling after the line heating. The experimental results show the angular misalignment changes in line heating. Heated surface of normalizing steel material expanded to $-0.3^{\circ}$ and reduced to $+0.2^{\circ}$ after cooling. And during cooling at $194^{\circ}C$ for 1,500 seconds, Angular Misalignment began from - direction to + direction, passed the critical point to the default at 2,200 seconds and did not take place any more at $103^{\circ}C$ after the 2,700 seconds. Angular Misalignment results of TMCP steels and Normalizing steel material show same angular misalignment lasted 1,200 seconds, TMCP steel has given more expansion and contraction angle which is $0.2^{\circ}$ than that of the Normalizing steel. Length difference between expansion and contraction is about 0.3 mm.

• Journal of Pharmaceutical Investigation
• /
• 제38권6호
• /
• pp.393-398
• /
• 2008

A propofol delivery system was prepared using two biocompatible polymeric surfactants, poloxamer 407 and PEG 400. The nanoparticular stability of the micellar system was evaluated in terms of temperature change, storage time and composition. The particle size of the system was slightly increased with elevating temperature from $4^{\circ}C$ to $25^{\circ}C$, but its distribution was unimodal. At $40^{\circ}C$, the system presented a bimodal particle size distribution and the increase in the fraction of particles larger than 15 nm. This result might be due to the expansion of the nanoparticles through micellar swelling at the high temperature. It was found that propofol was gradually come out of the system, stored for a month at three different temperatures (4, 25 and $40^{\circ}C$). The drug loss was apparently dependent on temperature and the system composition. Increasing temperature induced the acceleration of the drug loss of $7{\sim}10%$ at $4^{\circ}C$ and $14{\sim}16 %$ at $40^{\circ}C$. This may be owing to the high diffusivity resulting from the swelling of the hydrophilic surface of the nanoparticle at high temperature. However, the addition of PEG 400 to the system led to the reduction of the drug loss. This result is associated with the previous investigation that PEG coverage decreased diffusion coefficient because of the formation of the denser structure on the surface of nanoparticulate. Nevertheless, the limited amount of PEG, less than 2% (w/v), should be used to prevent the precipitation and discoloration of the system.

• 한국태양에너지학회 논문집
• /
• 제33권5호
• /
• pp.51-59
• /
• 2013

It is usual to evaluate the performance of the cool roof by measuring in-site rooftop temperature using thermal infra-red camera. The principal advantage of rooftop thermal infrared image acquired in oblique vantage point of super high-rise building as a remote sensor is to provide, in a cost-effective manner, area-wide information required for a scattered rooftop target with different colors, utilizing wide view angle and multi-temporal data coverage. This research idea was formulated by incorporating the concept of traditional remote sensing into rooftop temperature monitoring. Correlations between infrared image of super high-rise building and in-situ data were investigated to compare rooftop surface temperature for a total of four different rooftop locations. The results of the correlations analyses indicate that the rooftop surface temperature by the infrared images of super high-rise building alone could be explained yielding $R^2$ values of 0.951. The visible permanent record of the oblique thermal infra-red image was quite useful in better understanding the nature and extent of rooftop color that occurs in sampling points. This thermal infrared image acquired in oblique vantage point of super high-rise made it possible to identify area wide patterns of rooftop temperature change subject to many different colors, which cannot be acquired by traditional in-site field sampling. The infrared image of super high-rise building breaks down the usual concept of field sampling established as a conventional cool roof performance evaluation technique.

• Journal of Electrical Engineering and information Science
• /
• 제2권5호
• /
• pp.65-71
• /
• 1997

We present heterojunction solar cells with a structure of metal/a-Si:H(n-i-p)/poly-Si(n-p)/metal for the terrestrial applications. This cell consists fo two component cells: a top n-i-p junction a-Si:Hi cell with wide-bandgap 1.8eV and a bottom n-p junction poly-Si cell with narrow-bandgap 1.1eV. The efficiency influencing factors of the solar cell were investigated in terms of simulation an experiment. Three main topics of the investigated study were the bottom cell with n-p junction poly-Si, the top a-Si:H cell with n-i-p junction, and the interface layer effects of heterojunction cell. The efficiency of bottom cell was improved with a pretreatment temperature of 900$^{\circ}C$, surface polishing, emitter thickness of 0.43$\mu\textrm{m}$, top Yb metal, and grid finger shading of 7% coverage. The process optimized cell showed a conversion efficiency about 16%. Top cell was grown by suing a photo-CVD system which gave an ion damage free and good p/i-a-Si:H layer interface. The heterojunction interface effect was examined with three different surface states; a chemical passivation, thermal oxide passivation, and Yb metal. the oxide passivated cell exhibited the higher photocurrent generation and better spectral response.

• Tribology and Lubricants
• /
• 제31권6호
• /
• pp.272-280
• /
• 2015

Recently, Luu suggested fatigue life equation that uses every term of the Crossland equation with stress gradient effect. Luu’s model, however, has a limit of being unable to coverage small radii that are less than a specified length. Furthermore, rolling model has a very small contact area compared to the rolling element size, and fatigue failure occurs on the small radius such as surface asperity by cyclic loading. Therefore, it is necessary to modify fatigue life equation in order to enable fatigue analysis for a small radius. In this paper, the fatigue life considering a stress gradient effect in rolling contact was obtained using Luu’s modified equation. Fatigue analysis was performed to study the effect of stress gradient on the fatigue life using newly adopted equation and to compare the results with pervious models. In order to do this, a series of simulation such as surface stress analysis, subsurface stress analysis, and fatigue analysis are conducted for two rolling balls of same size that contact each other. Through such a series of processes, the fatigue life can be calculated and equation that is proposed in this paper evaluates the fatigue life in case the contact area is small.