• 전력전자학회논문지
• /
• 제7권4호
• /
• pp.332-338
• /
• 2002

토카막 장치의 초전도 코일에 사용되는 전원 공급장치는 초대형급(20kA) 직류 전원 공급기로서 빠른 전류제어 응답성과 매우 작은 정상상태 리플이 필수적이다. 특히 역전류 공급이 가능한 회생형 컨버터의 운전중 전류 방향이 바뀌는 순간에도 전류기준값을 잘 추종하는 것이 중요하다. 이러한 조건들을 만족시키기 위하여 입력측에 2중 출력($\Delta$, Y)를 갖는 변압기와 출력단에 상간변압기(interphase transformer, IPT)를 이용한 12펄스 싸이리스터 듀얼 컨버터를 설계, 제작하였다. 각 컨버터에서 출력되는 전류의 합이 부하전류 지령치를 따르도록 제어하는 동시에 차 전류의 평균값이 영이 되도록 함으로써 각 컨버터의 부하 분담율을 일정하게 하여 상간 변압기의 포화를 방지한다. 대전류 코일 전류 공급장치의 양방향 전류 제어 성능을 높이기 위하여 위상각 검출 및 게이팅 지연각 구현을 디지털화하고 컨버터 전류방향 정역절환시 초기 응답특성을 개선하는 방법을 제안하였다. 또한 시뮬레이션과 실부하 전류실험을 통해 제안된 제어기의 동작성능을 확인하였다.

• Journal of Biosystems Engineering
• /
• 제25권6호
• /
• pp.489-496
• /
• 2000

This study was conducted in order to find an ideal working fluid kind and a proper filling amount in the heat pipe as well as an inclined angle of heat pipe when they are placed to recover exhaust gas heat in the hot air heater. Followings are the findings of this research. 1. Of the four different working fluids-gasoline kerosene distilled water and acetone-acetone filled heat pipe showed the best performance giving out more homogeneous temperature profile on the radiating part than the kerosene and gasoline heat pipe an carrying out heat transmitting function better than the distilled water heat pipe by 10~2$0^{\circ}C$ higher on the radiating part. Acetone would be a good choice for recycling of exhaust gas heat in the hot air heater. 2. Of the filling amount of working fluid inside the heat pipes dry-out situations possible caused by insufficient filling were found in the filling amount of 5, 7.5 and 10% heat pipes as heat supply rate increases gradually in the range of 50 to 15kJ/sec. but no dry-out and stabilized heat transmitting performance occurred in the heat pipes of 12.5 and 15% filling at the same heat supply rate. It recommends that filling amount shall exceed 12.5% at least with the working fluids of this experiment. 3. The test revealed that the heat transmitting performance of heat pipe was more affected by filling amount rather than inclined angle.

• 한국가스학회지
• /
• 제14권4호
• /
• pp.56-62
• /
• 2010

본 논문은 LPG 엔진의 전자제어센서에 대한 고장사례를 분석하고 고찰한 연구이다. LP가스의 연료 분사량을 컨트롤하는 크랭크 각도센서의 기능이상은 불규칙하고 불균일한 파형형태로 나타나고 있다. 크랭크 각도센서의 노이즈에 관련된 파형은 톱니형의 불규칙한 피크형상으로 나타났고, 2.46V 정도의 노이즈 레벨이 간헐적으로 발생하고 있다. 1번 TDC센서의 내부불량으로 인해 발생한 고장사례는 엔진의 출력을 떨어뜨리고 시동을 간헐적으로 꺼지게 하는 문제점을 초래한다. 산소센서의 성능이상은 센서의 배선에서 연결이 단절되었기 때문에 발생한 것으로 차량의 울컥거리는 현상과 엔진의 부조화 현상이 나타나고 있다. 에어 크리너를 이종품으로 사용한 경우는 신기가 정상적으로 공급되지 못했기 때문에 차량의 가속불량과 엔진의 부조화 현상이 발생하는 원인으로 작용하고 있었다.

• 한국분무공학회지
• /
• 제13권3호
• /
• pp.126-133
• /
• 2008

The atomization characteristics of the dual air supplying two-fluid nozzle were investigated experimentally using PIV and PDA systems. The twin-fluid nozzle is composed of three main parts: the feeding injector to supply fluid that is controlled by a PWM (pulse-width modulation) mode, the adaptor as a device with the ports for supplying the carrier and assist air, and the main nozzle to produce sprays. The main nozzle has the swirler with four equally spaced tangential slots, which gives the injecting fluid an angular momentum. The swirl angle in the swirler varied with $0^{\circ}$, $30^{\circ}$, $60^{\circ}$ and $90^{\circ}$. The ratios of carrier air to assist air and ALR (total air to liquid) were 0.55 and 1.23, respectively. The macroscopic behavior of the spray was investigated using PIV system, and the AMD and SMD distributions of the sprays were measured using PDA system. As a result, the SMD distribution increases along the radial distance, and it decreases with the increase of swirl angle in swirler.

• 한국산학기술학회논문지
• /
• 제12권5호
• /
• pp.2054-2060
• /
• 2011

본 연구의 목적은 경제적이고, 친환경적인 가솔린 직접 분사 인젝터의 분무특성을 연구하는 것에 있다. 분무도달거리, 분무각 그리고 혼합기 형성과 같은 인젝터의 특성을 가시화 실험을 통하여 측정하였다. 특히 분무압력과 분위기압력이 분무 침투거리와 분무각에 미치는 영향을 분석하였다. 가시화 실험을 위하여 정적 연소실과 연료 공급장치를 제작하였다. 초고속 카메라와 LED광원을 이용하여 분무형상을 촬영하였고, 촬영된 영상으로 분무 특성을 분석하였다. 연소실내의 분위기압력이 감소하고, 연료의 분무압력이 증가할수록 도달거리는 증가하였다. 분위기압력과 분무압력에 대해 분무각의 변화는 미소하지만, 분위기압력이 분무각에 더 큰 영향을 미치고 있다.

• KIEAE Journal
• /
• 제17권4호
• /
• pp.75-81
• /
• 2017

Purpose: Most contemporary office buildings supply external views, a sense of openness and a sense of time to their occupants by adopting the curtain walls, which are equipped with an outer cover having large window area. As a result, the amount of radiation increases, adversely affecting cooling load during the summer in office buildings. Although solar radiation decreases heating load and reduces energy costs during the winter period, due to the characteristics of offices where occupants work largely during daytime, the cooling load is important compared to the heating. Therefore, diverse measures to resolve those trade-offs and annual energy cost have been investigated. Method: In this study, the annual thermal load was comparatively analyzed according to the slat angle of the venetian blind along with lighting control technique. Result: After selecting effective conditions, in order to resolve such issues, this study established automated control strategies of slat angle depending on the window-to-wall ratio and zone orientation, so that the findings of this study can be effectively generalized to other circumstances.

• 한국항공우주학회지
• /
• 제39권6호
• /
• pp.487-497
• /
• 2011

자동회전 상태로 속도 증가 시 로터 속도의 변화와 피치 범위를 조사하기 위하여 수치 해석을 수행하였다. 정상 자동회전 상태를 구하기 위하여 과도모사법(Transient Simulation Method:TSM)을 사용하였다. 풍속의 증가에 대응하기 위하여 로터 블레이드를 2차원 압축성 Navier-Stokes 솔버로 해석하여 공력계수를 계산하였고 이를 과도모사법에 사용하였으며 유도 속도장 변화를 모사하기 위하여 Pitt/Peters 유도속도 이론을 적용하였다. 설정된 토크 평형 조건에서 풍속, 샤프트각, 피치각의 조합을 출력하여 로터의 회전속도와 변수의 범위를 조사하였다. 깃 끝 마하수의 변화에 따른 로터 회전속도의 변화를 살펴보았고 샤프트각의 감소에 따른 피치각의 트림 범위를 고찰하였다.

• 한국표면공학회지
• /
• 제44권2호
• /
• pp.50-54
• /
• 2011

Hydrophobic a-C:F film was coated on polycarbonate film with $CF_4$, $C_2F_6$ and HFC ($C_2F_4H_2$) gas in helium discharge generated by 5~100 kHz AC power supply at atmospheric pressure and room temperature. The highest water contact angle of the a-C:F film formed with $He/C_2F_6$ mixed gas is $155^{\circ}$. X-ray photoelectron spectrum showed that there was 40% of C-$CF_3$ bond at the surface of the super hydrophobic film. The contact angle and deposition rate were decreased with increasing substrate temperature. The contact angle was generally increased with the surface roughness of the film. The contact angle was high when the surface microstructure of the film was fine and sharp at the similar roughness and chemical composition of the surface.

• 전력전자학회논문지
• /
• 제20권5호
• /
• pp.421-428
• /
• 2015

An advanced direct torque control (DTC) with pulse width modulation (PWM) method is presented in this paper. The duty ratio calculation of the selected voltage vector is based on the voltage functions of the selected voltage vector according to the sector angle. The proposed DTC uses a conventional DTC scheme with six sector divisions and switching rules. However, the winding voltages are supplied by the PWM approach. Furthermore, the duty ratio of the switching voltage vector is determined by the flux, torque error, and motor speed. The base voltage that shall determine the duty ratio can be calculated by approximate voltage functions according to the voltage angle. For the calculation of base voltages, second-order quadratic functions are used to express the output voltage of the selected voltage vector according to voltage angle. The coefficients for the second-order quadratic functions are selected by the voltage vector, which is determined by the switching rules of the DTC. In addition, the voltage functions are calculated by the coefficients and voltage angle between the voltage vector and rotor position. The switching voltages from the calculated duty ratio can supply the proper torque and flux to reduce the ripple and error. The proposed control scheme is verified through practical experimental comparisons.

• 전기학회논문지
• /
• 제62권1호
• /
• pp.8-20
• /
• 2013

This paper deals with the concept design of HVDC system for controlling AC network reactive power. HVDC system can control active power and reactive power and the control concept of reactive power is similar to SVC(Static Var Compensator). Reactive power is controlled by adjusting firing angle of HVDC system under the condition that AC filters are switched. Reactive power depends on AC voltage condition, considering the steady-state and transient state to maintain the stable operation of AC network in the viewpoint of voltage stability. Therefore, in the design stage of HVDC, the reactive power required in the AC network must be considered. For the calculation of operation angle in HVDC system, the expected reactive power demand and supply status is examined at each AC system bus. The required reactive power affects the determination of the operation angle of HVDC. That is, the range of "control deadband" of operation angle should have the capability supplying the required reactive power. Finally, the reactive power control concepts is applied to 1GW BTB Pyeongtaek-Dangjin HVDC system.