• Toxicological Research
• /
• 제35권4호
• /
• pp.389-394
• /
• 2019

When conducting risk assessments of cosmetic ingredients, it is important that reliable exposure information is obtained for cosmetic products. As cosmetics are becoming more diverse, continuous effort must be made to obtain exposure data that reflect their growth and usage trends. The usage pattern of cosmetics, such as the application area and amount used, may differ by product type and also by country. We conducted a survey to compare the amount of sun spray and sun cream used in a usage environment in South Korea. The study was conducted on Haeundae Beach, one of the most popular beaches in South Korea. A total of 1,255 beachgoers participated in this study; 604 and 651 participants used the sun spray and sun cream, respectively, while sunbathing and enjoying water activities on the beach for one day. Exposure was analyzed following a probabilistic method. On comparing all subjects, it was found that the group that used sun spray (mean: 44.52 g/day) used significantly more product (p = 0.000) than those who used sun cream (mean: 20.51 g/day). By analyzing the daily exposure of sun spray and sun cream per unit body weight according to age and gender, the exposure amount of sun spray and sun cream was found to be highest among 2~9 year-old girls (mean for sun spray: 2.51 g/kg/day, p95: 5.50 g/kg/day, mean for sun cream: 0.79 g/kg/day, p95: 1.79 g/kg/day). The amount of sun spray used is approximately twice that of sun cream. Among both the sun spray and sun cream groups, the exposure amount per unit body weight was highest in girls younger than 10. These factors should be considered when conducting risk assessments of sun spray and sun cream.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2005년도 추계학술발표회 및 workshop
• /
• pp.183-184
• /
• 2005

Four different coatings deposited using cold spray process were studied with two different powder agglomerating techniques (spray d교 and evaporated powder) and using $TiO_2$ nano-sized powders with and without a 10wt% addition of ZnO. Characterization was performed by SEM, XRD and roughness test. Also the photocatalytic effect of the coatings was evaluated. Although the change of powder preparation techniques and the addition of ZnO into $TiO_2$ did not show appreciable variations in the surface morphology and Anatase phase transformation, it did show influence on the surface roughness of the coating, the highest roughness being found in the coatings made by spray powder prepared method. Regarding the photocatalytic effect it was observed that the using the spray dry coating and the addition of ZnO are promoter of purification at higher rates.

• Design & Manufacturing
• /
• 제2권2호
• /
• pp.20-24
• /
• 2008

Recently, the study for production technology is focused on cycle time reduction as various products are manufactured. In order to manufacture tool and die, rapid prototyping and rapid tooling are researched. Stereolithography apparatus, selective laser sintering, 3D printing, laminated object manufacturing are developed in rapid prototype. The purpose of this study is to develop rapid tooling technology using thermal spray process. This technology is not well-known to korea, but this study will be contributed in development of domestic molds industry through continuous research and development.

• 한국초전도학회:학술대회논문집
• /
• 한국초전도학회 2005년도 High Temperature Superconductivity Vol.XV
• /
• pp.67-67
• /
• 2005

• 한국재료학회지
• /
• 제12권10호
• /
• pp.809-813
• /
• 2002

Commercial nano crystalline $TiO_2$ powders were used to characterize photocatalyst, using thermal spray coating technique. The microstructure of coating layers were examined by SEM, FE-SEM and TEM. Also the cross sectional areas of TiO$_2$ coating layers were observed by SEM. The phases were analyzed by X-ray diffraction methed. Surface roughness and hardness were measured. It was found that phase transformation from anatase to rutile occurred, and the melted splats are all rutile, and unmeted nano particles were anatase. These unmelted anatase phase may enhance te play a role of photocatalyst.

• 반도체디스플레이기술학회지
• /
• 제10권4호
• /
• pp.125-130
• /
• 2011

The recent PCB (Printed Circuit Board) wet etcher has been needed to process pattern within $20{\mu}m$ width on a $20{\mu}m$ thick board. A previous PCB etcher can be used with multiple points of roller rolls or slips off a board. Also, the damage of the board by contacting the roller increases the friction defects. A vertical type boards transporting process is developed to solve the problems of boards friction and sagging in a horizontal etcher. In this research, CFD (Computational Fluid Dynamics) method is used to design an improved spray nozzle including the critical part of etcher, and establish the design method. Meanwhile, major spray characteristics are expected in diverse nozzle types and variables. Lastly, diverse simulation results are adapted to design an improved nozzle and spray system.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집E
• /
• pp.75-80
• /
• 2001

The present article deals with the numerical calculations for the inter-spray impingement of two diesel sprays under the conditions of high injection pressure. The Wave model involving the cavitation effect inside the nozzle was used for describing the atomization process. In particular, a hybrid model for drop collision was newly suggested in this study and compared with the O'Rourk's model, which has been widely used for diesel sprays. The impingement angles of 60 and 90 degrees were considered for simulation of non-evaporative diesel sprays. The calculated results for tip penetration were compared with experimental data and the Sauter Mean Diameter(SMD) characteristic was analyzed. It was concluded that the hybrid model slightly shows better agreement with experimental data than the O'Rourke's model. However, the more elaborate study should be needed for better understanding of spray-to-spray impingement phenomena.

• 한국분무공학회지
• /
• 제16권4호
• /
• pp.195-200
• /
• 2011

The pressure-swirl atomizer is widely used for the injectors in liquid rocket engines thanks to its high performance atomization and broad stability margin range. Spray mixed-interaction is an important area of study especially in cases where the propellant is mixed by spray interaction after an oxidant and a fuel are discharged separately. This interaction of sprays results in a significant modification of the spray characteristics such as the spatial evolution of the sprays. Experiments are conducted by a photographic technique to quantify the merged angle of the interaction regions of sprays from two pressure-swirl injectors. The experimental results show that the merged angle is mainly determined by the momentum flux ratios between two swirled sprays.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2002년도 학술대회지
• /
• pp.299-302
• /
• 2002

Characteristics of the twin fluid spray with ultrasonic forcing are examined in order to obtain the high efficiency of cold fog spray of the automatic pest control machine which has been widely used for the equipment cultivation recently. An electrostrictive vibrator of PZT BLT and a magnetostrictive vibrator of ${\pi}type$ with 28 kHz are applied as the ultrasonic transducer. All experiments are made and observed in 4 methods of spray ; a conventional spray method without ultrasonic forcing, an indirect vibration method with ultrasonic forcing, an improving duality method by ultrasonic forced within liquid, and a combined use method with both of the indirect vibration method and the improving quality method. In results, It was clarified that the ultrasonic effects the atomization of spray droplets and its efficiency is about $10{\%}$ and especially much more in the case of the combined use method.

• 한국건축시공학회지
• /
• 제3권2호
• /
• pp.141-148
• /
• 2003

This study deals with the estimation of material properties according to the construction condition for water-soluble rubberized asphalt waterproofing material of spray type. In this study, the waterproofing material property by the spray construction method is suggested by means of estimation its tensile performance and temperature dependency according to mix proportion ratio(4:1, 8:1), referenced viscosity and solid content (A:360cps, 76%, B:580cps, 79%, C:490cps, 70%), spray angle($30^{\circ}$, $45^{\circ}$, $60^{\circ}$), and spray distance(30cm, 50cm, 70cm). The result of testing are as follows. (1) The mix proportion ratio of principal agent and hardener is 4:1. (2) The viscosity referenced and solid content are 490cps and 70%. (3) The spray angle referenced is $45.^{\circ}$ (4) The distance referenced from concrete surface to spray gun is 40~50cm.