• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2001년도 전력전자학술대회 논문집
• /
• pp.247-251
• /
• 2001

Universal motors are mainly used for vacuum cleaner application. There are a lot of researches on SRM that applys home appliance throughout the world. The manufacturing cost of SRM drive makes it hard to expand its application to home appliance. This paper presents Single Phase SRM for the vacuum cleaner that has advantge in cost and performance over conventional universal motor. This paper proposes new power device driving scheme by using SRM switching characteristic. The driving scheme is very simple and inexpensive. Dwell Time Control method is used for the minimum switching loss of power device. The switching frequency of power device is less than 4.5kHz at 45,000rpm. By use of this scheme, power device based on very small switching losses can be used on SRM drive. Also, the biggest problem in single phase SRM is starting, this paper shows a new starting algorithm with two hall sensors, accelerating and running sensors, respectively. Finally, the proposed Single Phase SRM achieves higher efficiency and long life time compared to universal motor. Its life time is more than 1500 hours. Its life time is extended 4 times than that of conventional motor and its suction power is increased $20\%$ at the same volume of conventional universal motor.

• 지질공학
• /
• 제33권3호
• /
• pp.371-388
• /
• 2023

지층구성이 복잡하고 저투수성의 토양이 분포하는 경우 정화효율은 급격히 저하되고 실질적인 정화가 이루어지지 않거나 정화기간이 증가하는 등의 문제가 발생한다. 효율적인 정화를 위해서는 투수성이 개선되어 오염된 구간으로 정화제 주입하여 오염물질과 충분한 접촉이 이루어져야 한다. 본 연구는 균열형성과 효과적인 정화제 유도를 위해 플라즈마 블라스팅, 공압파쇄, 진공추출을 복합적으로 활용하는 PPV 공법의 유체 전달특성을 분석하고 기존공법과의 비교를 통해 개선효과를 평가하였다. 연구는 TPH(Total petroleum hydrocarbons)로 오염된 실제 오염부지에 대한 정화제 전달효과를 확인하기 위한 실증시험을 수행하였으며 정화제의 전달특성과 영향범위 등을 산정하기 위해 주입량과 주입시간을 모니터링하고, 정성적인 지중환경 변화요인을 확인하고자 전기비저항탐사를 수행하였다. 또한, 투수시험을 수행하여 각 공법에 대한 투수성 변화를 평가하였다. 정화제의 주입량 모니터링 결과, 주입량은 대조군 대비 실험군의 주입량이 약 4.74~7.48배 증가하였고, 단위 시간 당 주입 유량(L/min)은 약 5.00~7.54배 실험군의 전달률이 빠른 것으로 분석되었다. 전기비저항탐사 결과, 실험군의 비저항변화비는 대조군과는 달리 지표까지 영향을 주어 비저항값이 전체적으로 감소하는 경향을 보인다. 따라서 실험군은 지표 상부에 분포하는 토사층까지 과산화수소 등의 유체 확산이 이루어져 저비저항 변화비가 감소하는 것을 볼 수 있으며 주입정과 추출정 사이의 수평적 변화비는 약 1.12~2.38배 비저항값이 감소되었다. 투수성의 경우, 대조군과 실험군 모두 유사한 초기 투수성을 보였으나 과산화수소의 정화기작 영향으로 투수성이 감소하는 특성을 나타내는 것으로 확인되었다. 수리전도도의 변화를 정량적으로 평가하면, 대조군은 시험 종료 후 초기 수리전도도 대비 21.1%의 수리전도도를 나타내어 투수성이 급격히 저하되는 양상을 보였으나 실험군은 실험종료 후 초기치 대비 81.3%로 초기 수리전도도와 근접한 값을 나타내는 것으로 파악되었다. 현장조사로 확인된 수리전도도와 정화재 주입실험을 통한 정화제 주입용량(m³/hr), 토양특성분석(함수비, 밀도)을 통한 공극률(%)의 분석을 통해 영향반경(ROI)을 산정산 결과, PPV 공법의 영향반경(ROI)은 대조군에 비해 평균 220% 개선되는 것으로 확인되었다. 이와 같은 성과는 PPV 공법 적용으로 인하여 기존공법 대비 보다 넓은 범위에 걸쳐 효율적인 정화제 전달이 가능하고 정화기작에서 나타나는 투수성 저해요인을 상당부분 극복할 수 있으며, 약 2배 이상의 영향반경 증대를 통해 정화효율을 높일 수 있음을 지시하는 중요한 지표로 볼 수 있다.

• 한국정밀공학회지
• /
• 제21권4호
• /
• pp.194-201
• /
• 2004

Optical fibers are indispensable fer optical communication systems that transmit large volumes of data at high speed. But the aligning technology under the sub-micron accuracy is required for the precise axis adjustment and connection. For the purpose of precise alignment of the optical arrays, in this research, we have developed the 12-axis(with 8 automated axis and 4 manual axis) automatic optical fiber alignment system including the image processing-based searching system, the automatic loading system using the robot and the suction toot and the automatic UV bonding system. In order to obtain the sub-micron alignment accuracy, two 4-axis PC-based motion controllers and the two 50nm resolution 6-aixs micro-stage actuated by micro stepping motors are adopted. The fiber aligning procedure consists of two steps. Firstly, the optical wave guide and an input optical array are aligned by the 6-axis input micro-stage with the IR camera. The image processing technique is introduced to reduce primary manual aligning time and result in achieving the 50% decrease of aligning time. Secondly, the IR camera is replaced by the output micro-stage and a wave guide and two optical arrays are aligned simultaneously before the laser power intensity delivered to the optical powermeter reached the threshold value. When the aligning procedure is finished, the wave guide and arrays are W bonded. The automatic loading/unloading system is also introduced and the entire wave guide handing time is reduced significantly compared to the former commercial aligning system.

• 한국가시화정보학회:학술대회논문집
• /
• 한국가시화정보학회 2003년도 추계학술대회 논문집
• /
• pp.39-42
• /
• 2003

Leading edge extension(LEX) in a highly swept shape applied to a delta wing features the modern air-fighters. The LEX vortices generated upon the upper surface of the wing at high angle of attack enhance the lift force of the delta wing by way of increased negative suction pressure over the surfaces. The present 3-D stereo PIV includes the Identification of 2-D cross-correlation equation, stereo matching of 2-D velocity vectors of two cameras, accurate calculation of 3-D velocity vectors by homogeneous coordinate system, removal of error vectors by a statistical method followed by a continuity equation criterion and so on. A delta wing model with or without LEX was immersed in a circulating water channel. Two high-resolution, high-speed digital cameras$(1280pixel\times1024pixel)$ were used to allow the time-resolved animation work. The present dynamic stereo PIV represents the complicated vortex behavior, especially, in terms of time-dependent characteristics of the vortices at given measuring sections. Quantities such as three velocity vector components, vorticity and other flow information can be easily visualized via the 3D time-resolved post-processing to make the easy understanding of the LEX effect or vortex emerging and collapse which are important phenomena occurring in the field of delta wing aerodynamics.

• 간호행정학회지
• /
• 제12권3호
• /
• pp.444-453
• /
• 2006

Purpose: The purpose of the study was to identify critical indicators for the development of efficient patient classification system in a emergency room. Method: This study involved following five steps. Step 1. Selection of the lists direct nursing services in the ER. Step 2. Measurement of the time of direct nursing services from Aug. 31st to Nov. 30th, 2005. Step 3. Classification of the patients according to the nursing care time. Step 4. The determination the critical indicators for different patient classes. Result: Determinate indicators were as follow: 3 items in the first group (vital sign checking, IV route starting, blood sampling), 3 items in the second group (vital sign checking, fluid infusion, blood sampling), 9 items in the third group (I/O checking, $O_{2}$ inhalation, suction, fluid infusion, IV bolus, Central catheter preparation & management, blood sampling, intubation preparation & management, postmortem management), 7 items in the fourth group (EKG monitoring, BP monitoring, $O_{2}$ inhalation, fluid infusion, using the specific drugs, CPR, postmortem management). Conclusion: This study can help future studies which measure nursing services standard time or assigns value to emergency nursing services.

• Journal of Biosystems Engineering
• /
• 제31권3호
• /
• pp.161-167
• /
• 2006

The purpose of this study is to find the optimal conditions of PCM slurry manufacturing equipment for saving the marketing cost and keeping the original quality of products. In addition, the characteristics of the movable container for shipping or distributing products is analysed. The major results are as follows. 1. PCM thermal storage system is designed with the conditions of temperature($-5{\sim}10^{\circ}C$), cold chain time(30 minutes), and one time usage(50 liter). This system includes tank, freezer, circulating pump, cycle type heat exchanger, swelling tank, equipment of supplying PCM supplying unit includes cold tank, cycle type heat exchanger, suction unit and control equipments, etc. 2. After ability test of PCM thermal storage system, it shows that the required freezing time of PCM thermal storage system is less than one of the previous system. The reason is that churn (top and bottom) and compulsion circulation are occurred simultaneously and unit cooler type method is better than chiller type method. 3. By the experiment of transportation latent heat container, it is decided that the best container is $K_1$ with latent heat temperature($0{\sim}5^{\circ}C$) and density(0.15%). However, for $K_l\;and\;K_2$, it is necessary more studies on latent heat thermal conditions and conditions of making method.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2004년도 춘계학술대회
• /
• pp.1672-1677
• /
• 2004

Leading edge extension(LEX) in a highly swept shape applied to a delta wing features the modem air-fighters. The LEX vortices generated upon the upper surface of the wing at high angle of attack enhance the lift force of the delta wing by way of increased negative suction pressure over the surfaces. The present 3-D stereo PIV includes the Identification of 2-D cross-correlation equation, stereo matching of 2-D velocity vectors of two cameras, accurate calculation of 3-D velocity vectors by homogeneous coordinate system, removal of error vectors by a statistical method followed by a continuity equation criterion and so on. A delta wing model with or without LEX was immersed in a circulating water channel. Two high-resolution, high-speed digital cameras($1280pixel{\times}1024pixel$) were used to allow the time-resolved animation work. The present dynamic stereo PIV represents the complicated vortex behavior, especially, in terms of time-dependent characteristics of the vortices at given measuring sections. Quantities such as three velocity vector components, vorticity and other flow information can be easily visualized via the 3D time-resolved post-processing to make the easy understanding of the LEX effect or vortex emerging and collapse which are important phenomena occurring in the field of delta wing aerodynamics.

• 대한간호학회지
• /
• 제25권3호
• /
• pp.441-456
• /
• 1995

This study was done to determine direct and in-direct nursing time in nursing units in hospital to ap-plied computer system and expect that those results contribute to measure efficiency of nursing practice and planning of nursing manpower. The design for study was a descriptive study. The study results are as follows. 1. Patients admitted to the Internal Medicine and General Surgery units were grouped into four. Group Ⅰ, 32.9% of the total patients, consisted patients whose condition was considered minor Group Ⅱ, 26.1%, was of those whose condition was considered moderate, Group Ⅲ, 41. 8%, moderate severe and Group Ⅳ, 29.2% the most severe. 2. Nursing intervention times by care type were as follows four minutes spent for suction eight minutes, for simple position change, ten minutes, for sheet change, seven minutes for a hot or cool compress, six minutes for dressing change, four minutes for Ⅰ.M. injection, six minutes for patient health education and five minutes for body temperature check. 3. Direct care time by patient group revealed the following : Group Ⅰ rquired 191.4 minutes, Group Ⅱ required 331.1 minutes, Group Ⅲ rquired 499.4 minutes, and Group Ⅳ rquired 1328.0 minutes. 4. The ratio of time for adequate nursing care and direct care time in the Internal Medicine and Goneral Surgery units was 67.4%-83.4% and 94.7%-99.3% in the Intensie Care Unit. 5. Average daily direct care time per patient was 5.5 hours in the Internal Medicine unit and 11.5 hours in the Intensive Care Unit. 6. Time spent in indirect care was 48.3 minutes for computer recording,34.8 minutes for giving and receiving patient information for shift duty, 28.0 minutes for eating and resting time, 26.6 minutes for transfering and identifying patients, 25.6 minutes for identifying Doctor's order, 23.9 minutes for recording vital signs. 7. Time spent in indirect care was 282.2 minutes by head nurses (charge nurses), 258.7 minutes by nurses and 261.6 minutes by nurse aids. 8. The average nurse's workload was 9.3 hours and daily indirect nursing time required 46.3%-50. 5% of above mentioned workload time. .9. The average daily indirect care time per patient was expected to be 57.7 minutes in the Internal Medicine unit and 3.3 hours in the Intensive Care Unit.

• 한국가시화정보학회지
• /
• 제9권4호
• /
• pp.74-79
• /
• 2011

In this study the change of free surface vortex is represented at different times according to height of water and with or without curtain wall installation. The air volume fraction is investigated at each condition of water level and the influence about creation of vortex is analyzed. The height of sump intake is taken as 100mm and the water level is divided into 5 steps. The sump model is the TSJ model and the curtain wall is applied by HI standard of America. The results shows that the free surface vortex can be identified on the isotropic surface at air volume fraction 1%~5% and the vortices make an air column from the free surface to the sump intake and are created and destroyed repeatedly. In the higher water level, less air is absorbed into the intake pipe. After curtain wall installation, the suction rate of the air volume fraction is decreased by 6.7%. The result of the vortex motion according to time, works on a cycle.

• 한국콘텐츠학회:학술대회논문집
• /
• 한국콘텐츠학회 2006년도 추계 종합학술대회 논문집
• /
• pp.849-852
• /
• 2006

본 연구에서는 전자파를 차단 및 흡수하는 물질을 개발하는 추세에 발맞추어 전자파를 흡수할 수 있는 물질을 이용하여 상품화 시키는 것에 초점을 두었다. 예컨대 휴대폰에서 전자파가 많이 발생하게 되는데 전자파를 흡수할 수 있는 물질을 이용하여 만든 캐릭터를 핸드폰 밧테리 부분에 부착 사용하여 전자파를 차단하고자 하는 것이다. 이때 차단하는 부위를 전자파 차단이란 본래 기능외에 캐릭터 개념을 도입하여 악세사리 겸용으로 부착하여 사용할 수 있는 캐릭터를 연구하고자 한다. 캐릭터디자인은 소비자설문조사를 실시하여 선호도가 가장 높은 것을 적용 반영하여 마무리하였다.