• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2005년도 춘계 학술발표회 논문집
• /
• pp.811-818
• /
• 2005

Stability analyses on the 17 railroad cut-off soil slopes were carried out. The influences of rainfall infiltration on the slope stabilities were taken into account by seepage analyses using finite element method and by assuming ground water tables to be located adjacent to soil surface. The validity of those analyses were evaluated by comparing the slope failure characteristics between analysis results and the past failure records. The analyses were not appropriate to estimate the failure surface and the method considering only the increase of pore-water pressure (reduction of matric suction) as the influence of rainfall cannot appropriately estimate the surficial failures that occurred most of the cut-off soil slopes. For the better estimation of the surficial failure, the influence of water flows over slope surface which erode soil mass and/or increase driving force, should be evaluated and considered.

• Geomechanics and Engineering
• /
• 제23권4호
• /
• pp.301-311
• /
• 2020

In this study, shear strength behavior of fine-grained soils was investigated under unsaturated conditions. The samples in the unsaturated state were subjected to a net normal stress (σ-u_a) of 40 kPa and different matric suctions (u_a-u_w) of 50, 100 and 150 kPa. The matric suction values applied in the triaxial tests were selected according to the bubbling pressures determined from the SWC curves. The study was carried out on prepared re-constituted cylindrical samples by uniaxial consolidation of soil slurries. First, consolidated drained (CD) triaxial compression tests were performed on the saturated samples and the cohesion and angle of internal friction were determined. After that, drained triaxial compression tests under matric suctions were performed on the unsaturated samples. In order to obtain unsaturated test results, cohesion and internal friction angle values of saturated samples were used. The nonlinear surface representing the shear strength surface was approximated consisting of two planes (double planar surface). The reason for the nonlinear behavior of some soils is that the amount of sand content contained in it is relatively high and the bubbling pressure/permanent water content value is relatively low.

• 유체기계공업학회:학술대회논문집
• /
• 유체기계공업학회 2004년도 유체기계 연구개발 발표회 논문집
• /
• pp.452-455
• /
• 2004

The influence of wake flow on a flat-plate blade having different shapes near the hailing edge has been investigated in this paper. Two different shapes near the trailing edge namely the pressure surface cutting (TP) and the suction surface cutting (TS) have been used. The calculation has been performed for two different angles of attack (a =10 and 15 degree) in both the cases. RANS equations have been solved using SST-model as a turbulence closure. Cp and CL values obtained for TS are higher compared to those obtained for TP. Also, the vorticity distribution obtained in case of TS is stronger as compared to that obtained in the case of TP The Karmann Vortex is observed in both the cases but it is more clear in TS case. It is found that in the case of TS, flow separation does not occur upto the trailing edge on both the suction and the pressure sides of the blade while in the case of TP, the flow separateson the pressure surface near the trailing edge of the flat-plate blade.

• 유체기계공업학회:학술대회논문집
• /
• 유체기계공업학회 2005년도 연구개발 발표회 논문집
• /
• pp.359-364
• /
• 2005

Centrifugal pump shows the strongest secondary flow. Wake is formed near pressure surface close to hub at impeller exit for centrifugal pump impeller. Pressure gradient drives secondary flow in the inducer region, while in the remaining region the following sources drive together: > Pressure gradient > Coriolis force Low-momentum fluid near suction surface hub moves toward pressure surface hub in mixed-flow pump impeller. Tip leakage vortex dominate secondary flow in axial-flow pump impeller. Tip leakage vortex dominate secondary flow in axial-flow in axial-flow pump impeller

• 한국항공우주학회지
• /
• 제39권8호
• /
• pp.735-743
• /
• 2011

본 연구에서는 직선형 터빈 캐스케이드 장치를 이용하여 분사영역으로 진입하고 퇴각하는 익형의 허브, 평균반경, 팁에 형성되는 표면에서의 압력을 정상상태에서 측정하였다. 익형은 축류형으로 코드가 200mm이며, 분사 노즐은 단면은 사각형으로 그 크기는 $200mm{\times}200mm$이다. 실험은 코드 기준으로 레이놀즈수 $3{\times}10^5$에서 수행되었다. 탈설계 성능을 측정하기 위하여 노즐의 설치각을 $58^{\circ}$, $65^{\circ}$와 $72^{\circ}$로 변경하면서, 노즐의 설치각 변화에 대한 익형에서 표면압 변화의 특성을 파악하였다. 또한 현절비를 1.25, 1.38, 1.67로 변경하면서 현절비 변화에 대한 익형의 표면압 변화를 측정하였다. 실험의 결과에서 익형이 분사영역으로 진입할 때 현절비가 적을수록 흡입면에서는 표면압력의 감소가 발생되었고 낮은 노즐설치각인 경우에는 역회전방향의 힘이 형성되었다. 아울러 양의 입사각으로 익형이 분사영역으로 진입할 때 흡입면의 앞부분에 낮은 압력이 형성되었다.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2008년 영문 학술대회
• /
• pp.25-34
• /
• 2008

In this paper, three-dimensional multiblade row unsteady Navier-Stokes simulations at a hot streak temperature ratio of 2.0 have been performed to reveal the effects of rotor tip clearance on the inlet hot streak migration characteristics in low pressure stage of a Vaneless Counter-Rotating Turbine. The hot streak is circular in shape with a diameter equal to 25% of the high pressure turbine stator span. The hot streak center is located at 50% of the span and the leading edge of the high pressure turbine stator. The tip clearance size studied in this paper is 2.0mm(2.59% high pressure turbine rotor height, and 2.09% low pressure turbine rotor height). The numerical results show that the hot streak is not mixed out by the time it reaches the exit of high pressure turbine rotor. The separation of colder and hotter fluid is observed at the inlet of low pressure turbine rotor. Most of hotter fluid migrates towards the rotor pressure surface, and only little hotter fluid migrates to the rotor suction surface when it convects into the low pressure turbine rotor. And the hotter fluid migrated to the tip region of the high pressure turbine rotor impinges on the leading edge of the low pressure turbine rotor after it goes through the high pressure turbine rotor. The migration of the hotter fluid directly results in very high heat load at the leading edge of the low pressure turbine rotor. The migration characteristics of the hot streak in the low pressure turbine rotor are dominated by the combined effects of secondary flow and leakage flow at the tip clearance. The leakage flow trends to drive the hotter fluid towards the blade tip on the pressure surface and to the hub on the suction surface, even partial hotter fluid near the pressure surface is also driven to the rotor suction surface through the tip clearance. Compared with the case without rotor tip clearance, the heat load of the low pressure turbine rotor is intensified due to the effects of the leakage flow. And the numerical results also indicate that the leakage flow effect trends to increase the low pressure turbine rotor outlet temperature at the tip region.

• Journal of applied mathematics & informatics
• /
• 제26권1_2호
• /
• pp.161-176
• /
• 2008

The effect of variable viscosity on MHD mixed convection Hiemenz flow over a thermally stratified porous wedge plate has been studied in the presence of suction or injection. The wall of the wedge is embedded in a uniform Darcian porous medium in order to allow for possible fluid wall suction or injection and has a power-law variation of the wall temperature. An approximate numerical solution for the steady laminar boundary-layer flow over a wall of the wedge in the presence of thermal diffusion has been obtained by solving the governing equations using numerical technique. The fluid is assumed to be viscous and incompressible. Numerical calculations are carried out for different values of dimensionless parameters and an analysis of the results obtained shows that the flow field is influenced appreciably by the magnetic effect, variable viscosity, thermal stratification and suction / injection at wall surface. Effects of these major parameters on the transport behaviors are investigated methodically and typical results are illustrated to reveal the tendency of the solutions. Comparisons with previously published works are performed and excellent agreement between the results is obtained.

• 대한기계학회논문집B
• /
• 제24권10호
• /
• pp.1285-1293
• /
• 2000

In port fuel injection system of SI engines, injected fuel is impinged onto the surface of intake valves and port-wall, and then formed the wall flow under the cold start operation. Wall flows entrained into the cylinder result in the unsteady and nonuniform mixture formation. Therefore, the spray impingement to the wall is considered as having negative influences such as lowering combustion efficiency and causing unburned hydrocarbon emissions. This study investigates the spray characteristics of the wall impinging air-assist spray in suction air flow. A PDPA was used to analyze the flow characteristics under the different conditions such as impingement angle and supplied air. Experimental data concerning the impinging sprays has been obtained in the vicinity of the wall. Measured droplets divided into the pre-impinging droplets which denote as the positive normal velocities and post-impinging droplets that describe as the negative normal velocities for the suction flow. Their velocities, size distributions and SMD are comparatively analyzed before and after the impingement.

• International Journal of Fluid Machinery and Systems
• /
• 제4권1호
• /
• pp.209-216
• /
• 2011

The flow upstream of a centrifugal pump impeller has been investigated by both experimental test and numerical simulation. For experimental study, the flow field at four sections in the pump suction is measured by using PIV method. For calculation, the three dimensional turbulent flow for the full flow passage of the pump is simulated based on RANS equations combined with RNG k-$\varepsilon$ turbulence model. From those results, it is noted that at both design lo ad and quarter load condition, the pre-swirl flow whose direction is the same as the impeller rotation exists at all four sections in suction pipe of the pump, and at each section, the pre-swirl velocity becomes obviously larger at higher rotational speed. It is also indicated that at quarter load condition, the low pressure region at suction surface of the vane is large because of the unfavorable flow upstream of the pump impeller.

• Applied Microscopy
• /
• 제40권2호
• /
• pp.109-116
• /
• 2010

본 연구에서는 뿌리 없이 분지된 줄기에서 기원한 포충낭으로 먹이를 빠르게 포획하는 수생형 통발 포충낭의 형태 구조적 특징을 전자현미경으로 연구하였다. 이들의 흡입식 포충낭에서는 입구 부위 및 덧문에 발달하는 구조들이 능동적 먹이 포획에 있어 다른 어느 구조보다도 중요한 기능을 수행할 수 있도록 분화되어 있다. 포충낭 입구에는 분지된 안테나 및 부속지들이 위치하고, 덧문 중앙 부위에는 4개의 감각모가 발달하여 먹이의 접촉자극을 감지하였다. 자극신호는 입구의 무병, 유병의 다양한 capitate형 분비모들이 소수성 점액물질을 분비하게 하여 이들을 피복하며 덧문을 닫아 먹이를 포획하였다. 덧문 안쪽의 threshold는 입구부분, pavement epithelium 층, 내부 구역으로 구분되며, 입구와 내부구역의 중간에 있는 pavement epithelium 층에는 소수성 큐티클이 피복된 밸름층이 형성되었다. 먹이가 포충낭의 내강으로 들어오면 내벽에 발달하는 2분지선과 4분지선들이 효소 등의 물질을 분비하여 이들을 소화 및 흡수하는 중요한 기능을 하였다. 이와 같이 통발의 흡입식 포충낭에서는 안테나, 감각모, 덧문, capitate형 분비모, 내벽의 분지선 등이 체계적이고 효율적인 방법으로 그 구조와 기능이 분화되어 식충의 기작을 수행하였다. 이후 포충낭의 분화발생을 생장단계별로 추적 연구하여 본 연구의 결과에 접목시키면 더 유용한 통발속 포충낭 구조 자료가 될 것이다.