• 대한기계학회논문집A
• /
• 제32권4호
• /
• pp.371-377
• /
• 2008

Our precedent study has reported glass-PDMS (polydimethylsiloxane) based biochip for the gene PCR (polymerase chain reaction). To prevent the contamination of bio sample, the once used biochip must not be used repeatedly. However, the fabrication cost of microheater and microsensor of the biochip was not cheap to use it as a disposable chip. This paper proposes new PCR-chip where the glass substrate integrated with the microheater and microsensor is detachable from the reaction chamber where the sample is injected. That makes it possible to reuse the glass substrate repeatedly. The performance of the proposed detachable PCR-chip was compared with that of the precedent monolithic PCR-chip. The results showed that the SRY (sex determining Y chromosome) gene PCR was successfully performed in the detachable chip compared with the monolithic chip. However, the more efforts to improve the efficiency of surface treatment of PDMS chip are needed to increase the possibility of applying the detachable chip to the detecting of male infertility.

• 한국정밀공학회지
• /
• 제25권9호
• /
• pp.32-37
• /
• 2008

Freestanding hydride vapor phase epitaxy grown GaN(Gallium Nitride) substrates subjected to various polishing methods were characterized for their surface and subsurface conditions, Although CMP(Chemical Mechanical Polishing) is one of the best approaches for reducing scratches and subsurface damages, the removal rate of Ga-polar surface in CMP is insignificant($0.1{\sim}0.3{\mu}m$/hr) as compared with that of N-polar surface, Therefore, conventional MP(Mechanical Polishing) is commonly used in the GaN substrate fabrication process, MP of (0001) surface of GaN has been demonstrated using diamond slurries with different abrasive sizes, Diamond abrasives of size ranging from 30nm to 100nm were dispersed in ethylene glycol solutions and mineral oil solutions, respectively. Significant change in the surface roughness ($R_a$ 0.15nm) and scratch-free surface were obtained by diamond slurry of 30nm in mean abrasive size dispersed in mineral oil solutions. However, MP process introduced subsurface damages confirmed by TEM (Transmission Electronic Microscope) and PL(Photo-Luminescence) analysis.

• 한국세라믹학회지
• /
• 제40권6호
• /
• pp.547-552
• /
• 2003

RF 마그네트론 스퍼터링법을 이용하여 유리기판위에 인가전력 100 W, 1.33Pa, Ar/O2=50 : 50, 20$0^{\circ}C$ 그리고 타겟과 기판사이의 거리 4 cm의 조건으로 ZnO 압전 박막을 성장시켰다. 증착된 박막의 결정성, 표면형상, 화학적 결합비와 전기적 특성을 XRD, SEM, AFM, RBS와 electrometer를 이용하여 측정 분석하였다 제조된 박막은 우수한 c축 우선 배향성을 보였고 또한 화학 양론적인 결합비를 나타내었다. 전극 구조가 single 및 double IDT를 갖는 ZnO/1DT/glass SAW 필터를 제작하여 특성을 분석한 결과, 전파속도는 각각 2,589 m/sec, 2,533 m/sec이었고, 삽입손실은 -11 dB과 -21 dB 값을 나타내어 박막형 SAW 필터로 응용이 기대된다.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2002년도 International Meeting on Information Display
• /
• pp.526-529
• /
• 2002

Various fluoride films on a glass substrate were prepared and characterized in order to determine the best seed layer for a microcrystalline silicon (${\mu}c$-Si) film growth. Among the various group-IIA-fluoride systems, the $CaF_2$films on glass substrates illustrated (220) preferential orientation and a lattice mismatch of less than 0.7% with Si. $CaF_2$ films exhibited a dielectric constant between $4.1{\sim}5.2$ and an interface trap density ($D_{it}$ as low as $1.8{\times}10^{11}\;cm^{-2}eV^1$. Using the $CaF_2$/glass structure, we were able to achieve an improved ${\mu}c$-Si film at a process temperature of 300 $^{\circ}C$. We have achieved the ${\mu}c$-Si films with a crystalline volume fraction of 65%, a grain size of 700 ${\AA}$, and an activation energy of 0.49 eV.

• 한국전기전자재료학회논문지
• /
• 제18권1호
• /
• pp.75-80
• /
• 2005

In this thesis, We Fabricated Cu thin films of 1000 $\AA$, 3000 $\AA$, and 6000 $\AA$ thickness on the single crystal sapphire, polycrystal alumina, and amorphous slide glass substrates deposited by electron beam evaporation(EBE) method. We investigated properties of resistivity and adhesion of these Cu thin films under various conditions, substrate temperature(room temperature, 10$0^{\circ}C$, 20$0^{\circ}C$ under vacuum) and annealing temperatures(400 $^{\circ}C$, 600 $^{\circ}C$ for 30 min after the deposition). We found that these adhesion was increased in order of slide glass, sapphire, and alumina. The adhesion of the Cu thin films on alumina was high value about 4 times, compared with that of the Cu thin films on slide glass. We found that these resistivities were decreased with increasing substrate temperature and thin film thickness. The resistivity(2.05 $\mu$Ω\ulcornercm) of the Cu thin films with 6000 $\AA$ thickness at 200 $^{\circ}C$ on the slide glass was low value, compared with that of aluminum(2.66 $\mu$Ω\ulcornercm).

• 한국전기전자재료학회논문지
• /
• 제21권5호
• /
• pp.434-439
• /
• 2008

Silver pastes as the outer electrodes have been prepared using Pb-free glass frits with different content of $Bi_2O_3$ and the effects of glass composition on the degradation behaviors of the Ag electrodes were investigated using the change of adhesion between Ag electrode and alumina substrate with thermal cycle stress. Low adhesion and high surface resistance were observed in Ag electrode using glass frit with a $Bi_2O_3$ content of 60 wt%, owing to the open microstructure formed at the firing temperature of $600^{\circ}C$. When the $Bi_2O_3$ was increased to 80 wt% in the glass frit, the Ag electrodes had a dense microstructure with high adhesion and a low surface resistance. Delamination of the Ag electrodes was a major failure mode under thermal cycle stress and this was attributed to residual stress due to the thermal expansion mismatch between the Ag electrode and the alumina substrate.

• 센서학회지
• /
• 제5권6호
• /
• pp.68-73
• /
• 1996

고주파 마그네트론 스펏터링법을 이용하여 유리 및 (012)면인 사파이어 기판위에 ZnO박막을 제조하였다. 유리기판위에는 (002)면을 갖는 ZnO 다결정박막이 제조되었으며, (012)면인 사파이어 기판위에는 (110)면인 ZnO에 피택셜 박막이 제조되었다. 유리 및 사파이어 기판위에 제조된 ZnO박막의 표면탄성파 특성을 조사하였다. 유리 및 사파이어 기판에 대한 중심주파수에서의 전파속도는 각각 2680 m/sec 및 5980 m/sec였으며, 기본모드에서 구한 결합계수는 각각 0.98 % 및 1.44 %였다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2007년도 하계학술대회 논문집 Vol.8
• /
• pp.338-338
• /
• 2007

Photo-conductive properties of CdS films deposited on glass substrates by a reactive sputtering in Ar atmosphere were characterized as a function of working pressure and the film thickness. The XRD measurements of CdS films revealed obvious (002) preferred orientation. In 300nm-thick of films, difference between dark and photo-resistance increases with increasing working pressure within the films. The films at 5 mTorr of working pressure show a dark resistance of approximately $1\;{\times}\;10^6\;{\Omega}/{\square}$ and a photo-resistance of $3\;{\times}\;10^4\;{\Omega}/{\square}$. The decrease dark- and photo-resistance of films as thickness decrease were $1.4\;{\times}\;10^6$ and $3\;{\times}\;10^4\;{\Omega}/{\square}$, respectively. CdS films deposited on glass substrates are considered tobe suitable for photo-conductivity materials in stealth radome applications.

• 한국결정학회지
• /
• 제11권3호
• /
• pp.167-172
• /
• 2000

CaTiO₃:Pr phosphor thin films were prepared on Si(100), ZnO/glass, Corning glass and ITO/glass by rf magnetron reactive sputtering. The effects of deposition parameters such as oxygen partial pressure, substrate temperature, and annealing conditions on crystallinity and compositional variation of the films were investigated. PL spectra of CaTiO₃:Pr phosphor thin films exhibited red regime peaking at 613 nm and enhanced PL intensity was observed for the film annealed in vacuum atmosphere as compared to the deposit annealed in N₂ environment.

• 한국표면공학회지
• /
• 제43권6호
• /
• pp.272-277
• /
• 2010

We investigated the life time characteristics of OLED device with aluminium oxide ($AlO_x$) passivation film on glass substrate and polyethylene terephthalate (PET) substrate by RF magnetron sputtering for the transparent barrier film applied to flexible OLED device. Basic buffer layer was determined as $Alq_3$(500 nm)-LiF(300 nm)-Al(1200 nm), and the most suitable aluminium oxide ($AlO_x$) film have been formed when the partial volume ratio of oxygen was 20% and the sputtering power was 100 watt and the minimum thickness of buffer was $2\;{\mu}m$. $AlO_x$/epoxy hybrid film was also used as a effective passivation layer for the purpose of improving life time characteristics of OLED devices with the glass substrate and the plastic substrate. Besides, the simultaneous deposition of $AlO_x$/epoxy film on back side of PET could result in better improvement of life time.