• Journal of Electrochemical Science and Technology
• /
• 제8권3호
• /
• pp.197-205
• /
• 2017

Lead dioxide thin films were electrodeposited on nickel substrate from acidic lead nitrate solution. Current efficiency and thickness measurements, cyclic voltammetry, AFM, SEM, and X-ray diffraction experiments were conducted on $PbO_2$ surface to elucidate the effect of lead nitrate concentration, current density, temperature on the morphology, chemical behavior, and crystal structure. Experimental results showed that deposition efficiency was affected by the current density and solution concentration. The film thickness was independent of current density when deposition from high $Pb(NO_3)_2$ concentration, while it decreased for low concentration and high current density deposition. On the other hand, deposition temperature had negative effect on current efficiency more for lower current density deposition. Cyclic voltammetric study revealed that comparatively more ${\beta}-PbO_2$ produced compact deposits when deposition was carried out from high $Pb(NO_3)_2$ concentration. Such compact films gave lower charge discharge current density during cycling. SEM and AFM studies showed that deposition of regular-size sharp-edge grains occurred for all deposition conditions. The grain size for high temperature and low concentration $Pb(NO_3)_2$ deposition was bigger than from low temperature and high concentration deposition conditions. While cycling converted all grains into loosely adhered flappy deposit with numerous pores. X-ray diffraction measurement indicates that high concentration, high temperature, and high current density favored ${\beta}-PbO_2$ deposition while ${\alpha}-PbO_2$ converted to ${\beta}-PbO_2$ together with some unconverted $PbSO_4$ during cycling in $H_2SO_4$.

• 한국전기전자재료학회논문지
• /
• 제18권6호
• /
• pp.571-575
• /
• 2005

In order to improve the efficiency of dye-sensitized solar cell (DSSC), $TiO_2$ electrode screen-printed on transparent conducting oxide (TCO) substrate was sintered in variation with different temperature$(350\;to\;550^{\circ}C)$. $TiO_2$ electrode on fluorine doped tin oxide (FTO) glass was assembled with Pt counter electrode on FTO glass. I-V properties of DSSCs were measured under solar simulator. Also, effect of sintering temperature on surface morphology of $TiO_2$ films was investigated to understand correlation between its surface morphology and sintering temperature. Such surface morphology was observed by atomic force microscopy (AFM). Below sintering temperature of $500^{\circ}C$, efficiency of DSSCs was relatively lower due to lower open circuit voltage. Oppositely, above sintering temperature of $500^{\circ}C$, efficiency of DSSCs was relatively higher due to higher open circuit voltage. In both cases, lower fill factor (FF) was observed. However, at sintering temperature of $500^{\circ}C$, both efficiency and fill factor of DSSCs were mutually complementary, enhancing highest fill factor and efficiency. Such results can be explained in comparison of surface morphology with schematic diagram of energy states on the $TiO_2$ electrode surface. Consequently, it was considered that optimum sintering temperature of a-terpinol included $TiO_2$ paste is at $500^{\circ}C$.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2012년도 제43회 하계 정기 학술대회 초록집
• /
• pp.105-105
• /
• 2012

We have developed a photoemission-assisted plasma-enhanced chemical vapor deposition (PAPE-CVD) [1,2], in which photoelectrons emitting from the substrate surface irradiated with UV light ($h{\nu}$=7.2 eV) from a Xe excimer lamp are utilized as a trigger for generating DC discharge plasma as depicted in Fig. 1. As a result, photoemission-assisted plasma can appear just above the substrate surface with a limited interval between the substrate and the electrode (~10 mm), enabling us to suppress effectively the unintended deposition of soot on the chamber walls, to increase the deposition rate, and to decrease drastically the electric power consumption. In case of the deposition of DLC gate insulator films for the top-gate graphene channel FET, plasma discharge power is reduced down to as low as 0.01W, giving rise to decrease significantly the plasma-induced damage on the graphene channel [3]. In addition, DLC thickness can be precisely controlled in an atomic scale and dielectric constant is also changed from low ${\kappa}$ for the passivation layer to high ${\kappa}$ for the gate insulator. On the other hand, negative electron affinity (NEA) of a hydrogen-terminated diamond surface is attractive and of practical importance for PAPECVD, because the diamond surface under PAPE-CVD with H2-diluted (about 1%) CH4 gas is exposed to a lot of hydrogen radicals and therefore can perform as a high-efficiency electron emitter due to NEA. In fact, we observed a large change of discharge current between with and without hydrogen termination. It is noted that photoelectrons are emitted from the SiO2 (350 nm)/Si interface with 7.2-eV UV light, making it possible to grow few-layer graphene on the thick SiO2 surface with no transition layer of amorphous carbon by means of PAPE-CVD without any metal catalyst.

• 대한전자공학회논문지TC
• /
• 제43권5호
• /
• pp.147-155
• /
• 2006

본 논문에서는 Mushroom 형태 PBG 구조의 소형화 특성 개선을 위한 새로운 주기 구조를 제안하였다. 이러한 기술적 방법은 기존 유전체 기판의 두께와 전체적인 상부 패치의 크기 증가 없이 단위 주기 구조의 등가 커패시턴스 증가를 위한 구조 변형에 기반을 두고 있다. 또한 소형화된 PBG 구조의 부설에 의해 안테나의 표면파 억제를 위한 새로운 구조를 제안하였다. 기존 패치 안테나와 소형 Mushroom PBG 구조가 부설된 패치 안테나의 방사 패턴과 이득 비교를 통해서 표면파 억제가 효과적으로 이루어졌음을 확인할 수 있었다. 5.37GHz의 기본 동작 모드에서 Mushroom PBG 구조가 없는 패치 안테나의 이득은 $6.43dB{\imath}$, 기본 Mushroom PBG 구조와 바람개비 Mushroom 구조가 부설된 패치 안테나의 경우 각각 7.24dB{\imath}$와 $7.53dB{\imath}$의 이득을 나타내었다. 소형 Mushroom PBG 부설에 의해 안테나의 후방 방사 특성이 개선으로 전체적인 안테나의 효율도 증가하였다.

• 한국세라믹학회지
• /
• 제39권1호
• /
• pp.86-91
• /
• 2002

고체 산화물 연료전지(Solid Oxide Fuel Cell; SOFC)는 무공해 청정에너지원으로서 기존의 발전방식을 대체할 차세대 에너지원으로 각광받고 있다. 고체산화물 연료전지의 구성요소는 크게 음극(anode), 양극(cathode), 전해질(electolyte)로 나뉘어 지는데 그 중 음극은 전극으로서의 역할은 물론 음극지지형인 경우 지지체 역할가지 수행해야 하기 때문에 아주 다양한 특성이 요구되어지고 있다. 그 중에서도 연료전지 성능의 최대 감쇄요인으로 지적되고 있는 분극저항을 줄이기 위해서는 높은 전기전도도와 높은 가스투과도가 요구되고있다. 본 연구에서는 음극 제조과정 중 첨가하는 기공 전구체의 종류에 따라 기판의 기공구조가 어떻게 바뀌는지 또 그로 인해 기판의 미세구조 및 전기전도도가 어떠한 영향을 받는지 관찰하였다. 결과 음극기판의 미세구조 및 전기전도도는 기공전구체의 종류에 따라 크게 달라졌으며 특히 이방성을 가지는 기공전구체의 사용은 전도성상의 단락 및 비효율적인 기공의 양산을 가져와 결과적으로 연료전지 성능을 악화시킬 것으로 예상된다.

• Journal of Microbiology and Biotechnology
• /
• 제28권9호
• /
• pp.1447-1456
• /
• 2018

The amylosucrase encoding gene from Deinococcus geothermalis DSM 11300 (DgAS) was codon-optimized and expressed in Escherichia coli. The enzyme was employed for biosynthesis of three different dihydroxybenzene glucosides using sucrose as the source of glucose moiety. The reaction parameters, including temperature, pH, and donor (sucrose) and acceptor substrate concentrations, were optimized to increase the production yield. This study demonstrates the highest ever reported molar yield of hydroquinone glucosides 325.6 mM (88.6 g/l), resorcinol glucosides 130.2 mM (35.4 g/l) and catechol glucosides 284.4 mM (77.4 g/l) when 400 mM hydroquinone, 200 mM resorcinol and 300 mM catechol, respectively, were used as an acceptor substrate. Furthermore, the use of commercially available amyloglucosidase at the end of the transglycosylation reaction minimized the gluco-oligosaccharides, thereby enhancing the target productivity of mono-glucosides. Moreover, the immobilized DgAS on Amicogen LKZ118 beads led to a 278.4 mM (75.8 g/l), 108.8 mM (29.6 g/l) and 211.2 mM (57.5 g/l) final concentration of mono-glycosylated product of hydroquinone, catechol and resorcinol at 35 cycles, respectively, when the same substrate concentration was used as mentioned above. The percent yield of the total glycosides of hydroquinone and catechol varied from 85% to 90% during 35 cycles of reactions in an immobilized system, however, in case of resorcinol the yield was in between 65% to 70%. The immobilized DgAS enhanced the efficiency of the glycosylation reaction and is therefore considered effective for industrial application.

• Transactions on Electrical and Electronic Materials
• /
• 제11권6호
• /
• pp.279-284
• /
• 2010

This study has been carried out to determine the optimal process conditions of $AZO:H_2$ thin films for the maximization of the transmittance of a blue GaN light-emitting diode (LED) with a wavelength of 470 nm. The Al-doped zinc oxide $(AZO):H_2$ thin films were deposited on a sapphire substrate by radio-frequency magnetron sputtering system with varying substrate temperatures, working pressures and annealing temperatures temperature, working pressure and annealing imposed on a AZO (2wt% $Al_2O_3$) ceramic target. The effect of these variables was investigated in order to improve the light extraction efficiency of the LED. As a result, the (002)-oriented peak was found in all the $AZO:H_2$ thin films. The lowest resistivity and the best transmittance at a wavelength of 470 nm was found to be $4.774\;{\times}\;10^{-4}\;{\Omega}cm$ and 92% at a substrate temperature of $500^{\circ}C$, working pressure of 7 mTorr and annealing temperature of $400^{\circ}C$. The transmittance of the $AZO:H_2$ thin film for the Blue GaN LED was improved by approximately 13% relative to that of a ITO thin film (T = 79%).

• BMB Reports
• /
• 제31권1호
• /
• pp.53-57
• /
• 1998

The CMCax gene from Acetobacter xylinum ATCC 23769 was cloned and expressed in E. coli. With this gene, three gene products - mature CMCax, CMCax containing signal peptide(pre-CMCax), and a glutathione-S-transferase(GST)-CMCax fusion enzyme - were expressed. CMCax and pre-CMCax are aggregated to multimeric forms which showed high CMC hydrolysis activity, whereas GST-CMCax was less aggregated and showed lower activity, indicating that oligomerization of CMCax controbutes to the cellulose hydrolysis activity to achieve greater efficiency. The enzyme was identified to be an $\beta$-1,4-endoglucanase, which catalyzes the cleavage of internal $\beta$-1,4-glycosidic bonds of cellulose. The reaction products, cellobiose and cellotriose, from cellopentaose as a substrate, were identified by HPLC. Substrate specificity of cellotetraose by this enzyme was poor, and the reaction products consisted of glucose, cellobiose, and cellotriose in a very low yield. Theses results suggested that cellopentaose might be the oligosaccharide substrate consisting of the lowest number of glucose. The optimum pH of CMCax and pre CMCax was about 4.5, whereas that of GST-CMCas was rather broad at pH 4.5-8. The physiological significance of cellulose-hydrolyzing enzyme, CMCax, having such low $\beta$-1,4-endoglucanase activity and low optimum pH in cellulose-producing A. xylinum is not clearly known yet, but it seems to be closely related to the production of cellulose.

• 한국재료학회지
• /
• 제28권1호
• /
• pp.38-42
• /
• 2018

Continuous efforts are being made to improve the efficiency of Si solar cells, which is the prevailing technology at this time. As opposed to the standard front-lit solar cell design, the back-lit design suffers no shading loss because all the metal electrodes are placed on one side close to the pn junction, which is referred to as the front side, and the incoming light enters the denuded back side. In this study, a systematic comparison between the two designs was conducted by means of computer simulation. Medici, a two-dimensional semiconductor device simulation tool, was utilized for this purpose. The $0.6{\mu}m$ wavelength, the peak value for the AM-1.5 illumination, was chosen for the incident photons, and the minority-carrier recombination lifetime (${\tau}$), a key indicator of the Si substrate quality, was the main variable in the simulation on a p-type $150{\mu}m$ thick Si substrate. Qualitatively, minority-carrier recombination affected the short circuit current (Isc) but not the opencircuit voltage (Voc). The latter was most affected by series resistance associated with the electrode locations. Quantitatively, when ${\tau}{\leq}500{\mu}s$, the simulation yielded the solar cell power outputs of $20.7mW{\cdot}cm^{-2}$ and $18.6mW{\cdot}cm^{-2}$, respectively, for the front-lit and back-lit cells, a reasonable 10 % difference. However, when ${\tau}$ < $500{\mu}s$, the difference was 20 % or more, making the back-lit design less than competitive. We concluded that the back-lit design, despite its inherent benefits, is not suitable for a broad range of Si solar cells but may only be applicable in the high-end cells where float-zone (FZ) or magnetic Czochralski (MCZ) Si crystals of the highest quality are used as the substrate.

• KSBB Journal
• /
• 제4권3호
• /
• pp.221-228
• /
• 1989

각종 섬유질 효소당화반응조내의 현탁액 혼합교반 양상이 효소당화에 미치는 영향을 검토하기 위하여 3종의 대표적인 bioreactor;vertical impeller type bioreactor-(VITB), horizonatl paddle type bioreactor(TDTB)를 제작하여 그 효용성을 비교 검토하였다. 최적 교반강도는 impel-ler나 paddle로 현탁핵을 교반하는 VITB와 HPTB가 각각 100rpm, 그리고 통자체를 회전시켜 교반하는 TDTB가 200rpm이었으며 TDTB에 부착된 baffle의 형태 및 크기는 큰 영향을 주지 않았다. 또한 VITB나 TDTB의 경우 과다한 교반은 효소의 실활을 유발시켜 오히려 섬유소당화를 저해하였다. 3종의 bioreactor의 최적 교반조건에서의 당화효율을 비교한 결과 VITB가 가장 높았으며 특히 고농도 섬유소 당화시 가장 높은 당화효율을 보여, 가장 효율적인 교반양상을 나타내는 것으로 보인다. 이로 미루어 impeller나 paddle의 물리적 충격에 의한 현탁액의 cellulose network를 파괴시키는 효소반응기가 단순히 교반혼합하는 반응기에 비하여 우수한 결과를 줌을 알 수 있었다. 반면 주어진 양의 당을 생산하는데 소요되는 동력소모를 검토한 결과 TDTB가 VITB에 비하여 다소 낮았으나 고농도의 경우는 급속히 증가되었다. 적절한 bioreactor의 선정에는 기질의 가격, 당화수율, 고농도 당화, 그리고 반응기의 scale-up의 용이성등이 종합적으로 검토되어져야 할 것이다.