• Current Applied Physics
• /
• v.18 no.11
• /
• pp.1381-1387
• /
• 2018

One dimensional (1D) grating has been fabricated (using focused ion beam) on 50 nm gold (Au) film deposited on higher refractive index Gallium phosphate (GaP) substrate. The sub-wavelength periodic metal nano structuring enable to couple photon to couple with the surface plasmons (SPs) excited by them. These grating devices provide the efficient control on the SPs which propagate on the interface of noble metal and dielectric whose frequency is dependent on the bulk electron plasma frequency of the metal. For a fixed periodicity (${\Lambda}=700 nm$) and slit width (w = 100 nm) in the grating device, the efficiency of SPP excitation is about 40% compared to the transmission in the near-field. Efficient coupling of SPs with photon in dielectric provide field localisation on sub-wavelength scale which is needed in Heat Assisted Magnetic recording (HAMR) systems. The GaP is also used to emulate Vertical Cavity Surface emitting laser (VCSEL) in order to provide cheaper alternative of light source being used in HAMR technology. In order to understand the underlying physics, far-and near-field results has been compared with the modelling results which are obtained using COMSOL RF module. Apart from this, grating devices of smaller periodicity (${\Lambda}=280nm$) and slit width (w = 22 nm) has been fabricated on GaP substrate which is photoluminescence material to observe amplified spontaneous emission of the SPs at wavelength of 805 nm when the grating device was excited with 532 nm laser light. This observation is unique and can have direct application in light emitting diodes (LEDs).

• Microbiology and Biotechnology Letters
• /
• v.7 no.4
• /
• pp.211-216
• /
• 1979

Air lift fermentor (ALF) is widely used for production of single-cell protein (SCP) from hydrocarbon and other carbon sources, because oxygen transfer efficiency is believed to be superior in the ALF to that in other conventional fermentors. However, the performance of ALF in terms of mixing is somewhat questionable. In this research, we studied about the performance of the ALF in SCP production using methanol fermentation process as a model system. The results show that ALF could be employed for SCP production or other fermentation processes when substrate is miscible and used at low concentration. With a high substrate concentration, it must be operated under high pressure or low dilution rate to meet the adequate oxygen transfer requirement.

• Corrosion Science and Technology
• /
• v.22 no.1
• /
• pp.1-9
• /
• 2023

This work studied the inhibitory effect of the combination of benzoate-intercalated hydrotalcite (HT-BZ) and Ce³⁺-loaded clay (Clay-Ce) on carbon steel (CS). HT-BZ was prepared by the co-precipitation method and Clay-Ce was fabricated by a cation exchange reaction. HT-BZ and Clay-Ce were assessed by scanning electron microscopy (SEM) and X-ray diffraction (XRD) coupled with zeta potential measurement. Electrochemical measurements coupled with scanning electron microscopy/energy-dispersive X-ray spectroscopy (SEM/EDX) were used for studying the inhibitory action of the mixture of HT-BZ and Clay-Ce on steel electrodes immersed in 0.1 M NaCl. For comparison, the inhibitory effect of HT-BZ or Clay-Ce alone was also evaluated. The results showed that HT-BZ combined with Clay-Ce provided synergistic inhibition of the CS substrate. The mixture of 0.5 g/L HT-BZ + 0.5 g/L Clay-Ce provided 93.5% inhibition efficiency. The protective mechanism of the HT-BZ + Clay-Ce mixture consisted of the reaction of released BZ and Ce³⁺ and the deposition of HT-BZ and Clay-Ce structures on the CS substrate.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.36 no.1
• /
• pp.49-55
• /
• 2023

The deposition of indium zinc oxide (IZO) thin films was carried out on substrate at room temperature by RF magnetron sputtering. The effects of substrate temperature, RF power and deposition pressure were investigated with respect to physical and optical properties of films such as deposition rate, electrical properties, structure, and transmittance. As the RF power increases, the resistivity gradually decreases, and the transmittance slightly decreases. For the variation of deposition pressure, the resistivity greatly increases, and the transmittance is decreased with increasing deposition pressure. As a result, it was demonstrated that an IZO film with the resistivity of 3.89 × 10^-4 Ω∙cm, the hole mobility of 51.28 cm²/Vs, and the light transmittance of 86.89% in the visible spectrum at room temperature can be prepared without post-deposition annealing.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.36 no.1
• /
• pp.23-28
• /
• 2023

This paper demonstrates a novel NAND flash memory structure and annealing configuration including through-silicon via (TSV) inside the silicon substrate to improve annealing efficiency using an electro-thermal annealing (ETA) technique. Compared with the conventional ETA which utilizes WL-to-WL current flow, the proposed annealing method has a higher annealing temperature as well as more uniform heat distribution, because of thermal isolation on the silicon substrate. In addition, it was found that the annealing temperature is related to the electrical and thermal conductivity of the TSV materials. As a result, it is possible to improve the reliability of NAND flash memory. All the results are discussed based on 3-dimensional (3-D) simulations with the aid of the COMSOL simulator.

• Ocean and Polar Research
• /
• v.45 no.1
• /
• pp.1-9
• /
• 2023

Marine microalgae have different collection methods depending on their habitat. In the case of adhesive microalgae, it is difficult to separate organisms from the substrate surface, and contamination is likely to occur during the sampling process. In this study, we analyzed the collection efficiency of adhesive microalgae using three artificial fiber materials (nylon, blend fabric, and viscose rayon). Each fiber showed different fiber diameter and pore characteristics (nylon 26.09 ㎛, blend fabric 56.6 ㎛, viscose rayon 101.3 ㎛). In addition, attached organisms were collected on the surface of artificial substrates at Bukseong Port in Incheon using each tested fiber material. After that, we investigated the population and species composition. The highest number of cells was found in nylon, which was 8 times higher than in the least collected viscose rayon material. In addition, we identified 24 microalgal species from the substrate, demonstrating that the species composition differed from that of surface water. The number of collected microalgae species varied depending on the fiber materials, with nylon containing all the adhesive microalgae. In contrast, only a few microalgae were observed in other fibers. These results suggest that, of the tested fibers, nylon material may be suitable for collecting adhesive microalgae. As a result, this study may be useful for future research on adhesive microalgae.

• Journal of electromagnetic engineering and science
• /
• v.19 no.2
• /
• pp.115-121
• /
• 2019

This paper presents the effects of the position of the split of a split-ring resonator (SRR) on the performance of a composite broadband printed dipole antenna. The antenna is made of two printed dipole arms enclosed by two rectangular and identically printed SRRs. One dipole arm and the SRR are printed on the top side of the substrate, while the other dipole arm and SRR are printed on the bottom side of the same substrate. By changing the position of the split on the SRR, different antenna characteristic values are obtained, namely, for impedance bandwidth and radiation patterns. The split position is thus a critical parameter in antenna design, because it influences the antenna's major performance immensely. Different split positions and their consequences for antenna performance are demonstrated and discussed. The antenna generates linearly polarized radiations, and it is computationally characterized for broadband characteristics. The optimized compact antenna has overall dimensions of 9.6 mm × 74.4 mm × 0.508 mm (0.06λ × 0.469λ × 0.0032λ at 1.895 GHz) with a measured fractional bandwidth of 60.31% (1.32 to 2.46 GHz for |S₁₁| <-10 dB) and a radiation efficiency of >88%.

• Journal of environmental and Sanitary engineering
• /
• v.11 no.1
• /
• pp.45-55
• /
• 1996

An experimental research was conducted in order to study the combined treatment o of municipal landfill leachate and municipal sewage. The landfill leachate was that of Nanjido landfill site, and the municipal sewage was that of Chungnang municipal sewage treatment plant in Seoul. Several sets of bench~scale sequencing batch reactor(SBR) were used as e experimental apparatus. Specially investigated items in this experiment were the removal efficiency of substrate and the influence of treatment time. The experiment lasted for about 2 years. The result are as follows ; 1. The characteristics of leachate were pH 7.5~8.2, BOD 80~336mg/L, COD 908~1,460mg/L, NH3-N 1,409~2,330mg/L, T~P 2.7~7.lmg/L, Cl~3,540~4,085mg/L, a and heavy metals are a very small amount. And the characteristics of sewage were pH 6.9~7.3, BOD 78.4~129.3mg/L, COD 121.2~305.0mg/L, T~N 14.9~36.4mg/L, T-P 2.3~8.9mg/L. 2. The treatability of leachate alone was not treat well. So for the good treatment of leachate, it was necessary to deal with the pretreatment before bi이ogical treatment and a combined treatment of municipal sewage. 3. The various contents of the leachate were 5%, 10%, 30%, and 50%, and the removal efficiency of COD was 86.0%, 82.8%, 60.6%, and 31.7%. The maximum content of the leachate which could be sucessfully treated by SBR in the combined treatment was 10% of that of sewage. And the removal efficiency of COD increased n notably, as its treatment time increased. 4. The various contents of the electrolytic treated leachate were 5%, 10%, 30%, and 50%, and the removal efficiency of COD was 89.9%, 86.1%, 79.2%, and 69.8%. The maximum content of the leachate which could be sucessfully treated by SBR in the combined treatment was 30 % of that of sewage. And the removal efficiency of C COD increased notably, as its treatment time increased.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.27 no.5
• /
• pp.307-311
• /
• 2014

Because of a waveguiding effect and total internal reflection caused by a difference in refractive indices, only 20% of generated light is emitted to the air and the rest is trapped or absorbed in the device. An improvement of outcoupled efficiency of organic light-emitting diodes was studied using a microlens array. Mold of microlens array was fabricated by using photo-lithography with the AZ9260 photoresist, and the microlens array was formed onto the glass substrate using the UV curing agent named ZPU13-440. Device structure consists of microlens/glass/ITO/TPD/$Alq_3$/LiF/Al. It was found that there is an improvement of external quantum efficiency by about 20% at the same current density for the device with the microlens array compared to that of the reference one. Simulated outcoupled efficiency shows the improvement by about 20% for the device with the microlens array compared to that of the reference one. These results are consistent with the experimental ones.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.47 no.4
• /
• pp.31-37
• /
• 2010

In this paper, highly efficient dual-band class-F power amplifiers(PAs) for cellular and WLAN bands are suggested and implemented. For the first step, single-band class-F amplifiers at 840MHz, 2.4GHz are designed using commercial E-pHEMT FETs. The performance of two single band PAs are as much as 81.2% of efficiency with the output power of 24.4dBm with 840MHz PA and 93.5% of efficiency with 22.4dBm from the 2.4GHz. For the dual-band class-F PA, the harmonic controlling circuit with ideal SPDT switch was suggested. The length of transmission line is variable by a SPDT switch. As a results, the operation in 840MHz showed the peak efficiency of 60.5% with 23.5dBm, while in 2.4GHz mode the efficiency was 50.9% with the output power of 19.62dBm. Besides, it is shown that the harmonic controller of class-F above 2Ghz could be implemented on the low cost FR-4 substrate.