• Journal of the Society of Disaster Information
• /
• v.2 no.1
• /
• pp.53-64
• /
• 2006

This study presents the laboratory properties on the frost heave under various moisture contents and compaction efforts in pavement subgrade soil. Many researches were conducted on the frost heave. However, the researches with the domestic soils have not been so active until now. In particular, the evaluation of the frost heave in pavement subgrade soils was not established by many researchers. The problems relating with the frost heave have been serious causes in the distresses of pavements. The study was performed using an appropriate field simulation. The research results revealed that the drainage conditions in earth work should be treated cautiously.

• Journal of the Korean Society of Safety
• /
• v.11 no.3
• /
• pp.160-167
• /
• 1996

The construction waste concrete produce from the demolished concrete structures. These waste concrete materials are useful and valuable for fill and subgrade and are considered to use as the subgrade material of the road. To use the subgrade of the road with the waste concrete, the several experiments involved with compaction test and laboratory C. B. R. etc. are performed. These experiments are compared with criteria of the road construction manual. It is shown that the quality of the construction waste concrete satisfies that of the subgrade mentioned in the road construction manual.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2002.03a
• /
• pp.357-364
• /
• 2002

This paper describes the feasibility of compacting subgrade layer in thicker lifts than currently permitted as 20 cm. This project involved constructing and testing a full scale test section in highway. Soil stiffness in field was evaluated by a nondestructive testing method, called Geogage. Quality control tests and FE Analysis were also conducted. Typical dynamic compaction roller of 11ton weight is applied for full scale test and a Mohr-Coulomb model and Plane strain condition are used for FE Analysis. The results showed that compaction-induced stress and dissipated energy are mainly depend on depth of soil and it could be possible to increase thickness of a lift.

• Journal of the Korean Geotechnical Society
• /
• v.34 no.12
• /
• pp.105-113
• /
• 2018

In this study, the engineering properties including bearing capacity of subgrades stabilized with a binder are analyzed by laboratory and field experiments. The main components of the binder are CaO and $SO_3$. After the binder was mixed with a low plasticity clay, the passing rates were relatively decreased as the sieve mesh size increased. Not only did the soil type change to silty sand, but engineering properties, such as the plasticity index and modified California bearing ratio (CBR), were improved for the subgrade. A comparison of the compaction curves of the stabilized subgrade and field soil compacted with the same energy demonstrated an increase of approximately 6% in the maximum dry unit weight, slight decrease in optimum moisture content, and considerable increase improvement in grain size. In the modified CBR test, the effect of unit weight and strength increase of the modified soil (with a specific amount of binder) was remarkably improved. As the proportion of granulated material increased after the addition of binder, the swelling was reduced by 3.3 times or more during initial compaction and 6.5 times by final compaction. The unconfined compressive strength of the specimens was maintained at the homogeneous value with a constant design strength. The stabilized subgrade was validated by applying it in the field under the same conditions; this test demonstrated that the bearing capacity coefficients at all six sites after one day of compaction exceeded the target value and exhibited good variability.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2002.10a
• /
• pp.411-418
• /
• 2002

In domestic road construction sites, the compaction control based on strength are widely performed through the direct method with high accuracy, such as Plate Loading Test or Field CBR test. It is impossible to manage all construction sites using the direct method because the direct method requires heavy reaction loads and long measurement time. Therefore, it is necessary to apply the indirect method that could control the relative density of construction sites on the whole. Indirect methods, such as Cone Penetration Test and Fall Cone Test, require extra time for data analyzing and fixed area for test device. In this paper, the field applicability of Soil Impact Hammer (SIH) was investigated comparing with the results of field measurement tests and laboratory compaction tests. SIH developed by Japan Construction Administration and Asanuma Ltd., is a kind of indirect methods for compaction checking. According to the results of SIH performed in domestic road construction site, the subgrade reaction modulus obtained from SIH are similar to that from Plate loading tests in the range of 10 to 40. In comparison with laboratory compaction test, similar compaction line are shown in the dry side of optimum moisture contents.

• International Journal of Highway Engineering
• /
• v.11 no.2
• /
• pp.85-98
• /
• 2009

The in-situ Compaction test using sand cone (RC) and Plate Bearing Capacity Test (PBT) has been widely used for evaluating the subgrade and subbase condition on the pavement system. However, because the in-situ RC and PBT test are expensive and take plenties of time for operation, these are very difficult to figure out the in-situ characteristics of subgrade and subbase strength in detail. Therefore, for faster and economical operation, this study is to compare the Light Falling Weight Tests and propose the LFWD test as the in-situ Compaction test. This study suggests the relationship between in-situ RC value, $K_{30}$, $M_R$ and $E_{LFWD}$ of the subgrade and subbase materials in Korea using the laboratory and in-situ testing.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2002.03a
• /
• pp.127-132
• /
• 2002

While the pavement design is based on mechanical property such dynamic elastic modulus, the quality of highway subgrade during construction is controled by the optimum moisture content(OMC) and maximum dry density(${\gamma}$$\_$dmax/). However, since the quality control based on the OMC and maximum dry density does not consider the mechanical characteristics, there is a conceptional gap between design and PMS(pavement management system). Therefore, it is necessary to develope a new qualify control system using mechanical property for highway construction in more rational way. To achieve this goal, it is planned to perform various laboratory tests to collect mechanical properties of subgrade soil samples from several highway construction sites and to propose the relationship between dry unit weight (or OMC) and mechanical parameters. In this paper, the experimental data so far obtained are presented and analyzed. In addition, further research plan is presented and discussed.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2000.03b
• /
• pp.435-440
• /
• 2000

It is important to pay careful attention to construction backfill for the structural integrity of concrete box culvert. The stability of the surrounding soil is important to the structural performance of most culverts. Good compaction by the dynamic compaction roller with big capacity is as effective as good backfill materials to increase the structural integrity of culvert. However structural distress of the culvert could be occur due to the excessive earth pressure by dynamic compaction load. In this study, 16 box culverts were constructed with various compaction materials and construction methods. Three types of on-site soils such as subbase, subgrade and roadbed materials were used as backfill materials in the test program. Compaction methods were adapted based on the site conditions. In most cases, dynamic compaction rollers with 10 to 16 ton weights were used and vibration speed were applied from 2400 to 2500 rpm for the great compaction energy. Some backfill compactions with good quality soils were carried out to examine the effect of EPS(Expanded Polystyrene) panels with changes of compaction thickness. This paper presents the main results of the research conducted to access the engineering performance of the backfill materials. The characteristics of earth pressures are discussed. It is observed that subgrade and roadbed materials are needed more careful compaction than subbase materials. It is shown that EPS panels are effective to mitigate dynamic lateral earth pressure on the culverts. It is also obtained that the dynamic pressure depends on the soil properties. In addition, the coefficient of dynamic earth pressure (K$\sub$dyn/=ΔP$\sub$H/ ΔP$\sub$V/) during compaction is discussed.

• 한국도로학회:학술대회논문집
• /
• 2006.10a
• /
• pp.199-204
• /
• 2006

• 한국도로학회:학술대회논문집
• /
• 2005.03a
• /
• pp.103-112
• /
• 2005