• 제목/요약/키워드: Subcarrier multiplexing

검색결과 94건 처리시간 0.021초

Performance analysis of WPM-based transmission with equalization-aware bit loading

  • Buddhacharya, Sarbagya;Saengudomlert, Poompat
    • ETRI Journal
    • /
    • 제41권2호
    • /
    • pp.184-196
    • /
    • 2019
  • Wavelet packet modulation (WPM) is a multicarrier modulation (MCM) technique that has emerged as a potential alternative to the widely used orthogonal frequency-division multiplexing (OFDM) method. Because WPM has overlapped symbols, equalization cannot rely on the use of the cyclic prefix (CP), which is used in OFDM. This study applies linear minimum mean-square error (MMSE) equalization in the time domain instead of in the frequency domain to achieve low computational complexity. With a modest equalizer filter length, the imperfection of MMSE equalization results in subcarrier attenuation and noise amplification, which are considered in the development of a bit-loading algorithm. Analytical expressions for the bit error rate (BER) performance are derived and validated using simulation results. A performance evaluation is carried out in different test scenarios as per Recommendation ITU-R M.1225. Numerical results show that WPM with equalization-aware bit loading outperforms OFDM with bit loading. Because previous comparisons between WPM and OFDM did not include bit loading, the results obtained provide additional evidence of the benefits of WPM over OFDM.

Snapping shrimp noise detection and mitigation for underwater acoustic orthogonal frequency division multiple communication using multilayer frequency

  • Ahn, Jongmin;Lee, Hojun;Kim, Yongcheol;Chung, Jeahak
    • International Journal of Naval Architecture and Ocean Engineering
    • /
    • 제12권1호
    • /
    • pp.258-269
    • /
    • 2020
  • This paper proposes Snapping Shrimp Noise (SSN) detection and corrupted Orthogonal Frequency Division Multiplexing (OFDM) reconstruction methods to increase Bit Error Rate (BER) performance when OFDM transmitted signal is corrupted by impulsive SSNs in underwater acoustic communications. The proposed detection method utilizes multilayer wavelet packet decomposition for detecting impulsive and irregularly concentrated and SSN energy in specific frequency bands of SSN, and the proposed reconstruction scheme uses iterative decision directed-subcarrier reconstruction to recover corrupted OFDM signals using multiple carrier characteristics. Computer simulations were executed to show receiver operating characteristics curve for the detection performance and BER for the reconstruction. The practical ocean experiment of SAVEX 15 demonstrated that the proposed method exhibits a better detection performance compared with conventional detection method and improves BER by 250% and 1230% for uncoded and coded data, respectively, compared with the conventional reconstruction scheme.

DVB-T 시스템을 위한 효율적인 주파수 및 심볼동기 구조 (An efficient Frequency and Symbol Synchronization Scheme for DVB-T System)

  • 이형욱;김기윤;최형진
    • 한국통신학회논문지
    • /
    • 제27권2C호
    • /
    • pp.170-183
    • /
    • 2002
  • 본 논문에서는 OFDM(Orthogonal Frequency Division Multiplexing) 전송방식을 채택한 DVB-D(Digital Video Broadcasting-Terrestrial) 시스템의 효율적인 주파수 및 심볼 동기 구조를 제안하였다. 주파수 동기시 고려해야 할 사항은 정규화된 주파수 오프셋(실제 주파수 오프셋/부반송파 간격)의 소수부가 $\pm$0.5 부근에 위치할 때, 알고리즘의 추정 성능이 안정적이지 못하여 동기화에 필요한 심볼이 많이 요구된다는 점이다. 본 논문에서 제안하는 주파수 동기 구조는 대략적인 주파수 동기를 여러 심볼 동안 추정한 평균값을 이용하여 정규화된 주파수 오프셋의 소수부가 $\pm$0.5 부근에 위치할 때의 모호성을 해결하고, 대략과 미세 주파수 동기를 동시에 추정하여 보상하는 효율적인 구조이다. 또한 기존의 OFDM 심볼 동기 수행시 대략과 미세로 나누는 동기 구조를 변경하여 윈도우 오프셋이 항상 보호구간 내의 일정 범위 안으로 잔류하도록 만들어 대략적인 심볼 동기 만으로도 다중경로 페이딩 채널에서 시스템의 성능 열화 없이 하드웨어 구현이 용이한 심볼 동기 구조를 제안하였다. 그리고, 광범위한 시뮬레이션에 의해 본 제안 방식의 우수성을 증명하였다.

페이딩 채널에서 적응 LDPC 부호화 MIMO-OFDM의 성능 분석 (On Adaptive LDPC Coded MIMO-OFDM with MQAM on Fading Channels)

  • 김진우;조경현;나극환
    • 전자공학회논문지 IE
    • /
    • 제43권2호
    • /
    • pp.80-86
    • /
    • 2006
  • 제4세대 무선 통신은 송신기와 수신기양단에 다중 안테나와 순시 채널의 상태 정보를 이용함으로써 LDPC와 OFDM 무선 전송에 있어서 MQAM(M-ary Quadrature Amplitude Modulation)을 사용하는 적응 공간 부반송파 부호화 변조 방식에 기반으로 하고 있다. 적응 부호화 변조는 시변 협대역 무선 채널에 대해서 대역 효율이 좋은 전송방식으로 인식되어 가고 있다. 전력이 제한된 AWGN 채널에 대해서, LDPC 부호들은 오류 제어 부호의 한 부류이며 이는 어떤 조건하에서는 터보부호보다 오류 정정 능력이 더 좋은 것으로 알려져 왔다. 본 논문에서는 MIMO 시스템에 적용된 LDPC 부호를 갖는 OFDM 방식과 적응 변조방식에 대해서 서술한다. 채널의 순시 정보를 알고 있다고 가정함으로써 각 부반송파에 대해서 비트와 전력 할당을 얻기 위한 최적화 알고리즘이 사용되였다. 시뮬레이션 결과는 제안한 시스템이 가능성을 가짐을 보여준다.

주파수영역 최적 위치 임펄스 삽입기법에 의한 OFDM-CQAM 시스템의 PAPR 개선 (PAPR Improvement of OFDM-CQAM System Through Optimum Position Impulse Insertion Scheme in Frequency Domain)

  • 곽재민
    • 한국항행학회논문지
    • /
    • 제23권3호
    • /
    • pp.258-263
    • /
    • 2019
  • OFDM (orthogonal frequency division multiplexing)은 다중경로 페이딩에 강하고 고속전송이 가능하다는 장점으로 널리 사용되고 있는 디지털 통신방식이나, 여러 부반송파 변조신호가 동위상으로 겹쳐지면서 송신신호의 PAPR (peak to average power ratio)이 높아진다는 단점을 가지고 있다. 송신단의 IFFT (inverse fast Fourier transform) 이전에 주파수 영역에서 높은 크기의 임펄스를 삽입하면, 쌍대성 특성으로 인해 시간영역의 OFDM 신호의 PAPR 감소 효과를 가져올 수 있다. 본 논문에서는 CQAM (cross quadrature amplitude modulation) 방식을 채용하는 OFDM 통신시스템에서 송신단의 IFFT 이전에 임펄스를 삽입함으로서 개선되는 PAPR 성능을 분석한다. 또한 PAPR을 최소화시킬 수 있는 최적의 임펄스 삽입위치 찾아내고 이를 적용하였을 경우의 PAPR 개선효과를 검증한다. 컴퓨터 시뮬레이션을 통해 주파수영역에서 삽입되는 임펄스 크기와 위치에 따라 OFDM-CQAM 시스템의 PAPR 개선효과가 기존 방식에 비해 우수함을 확인한다.

Delay and Doppler Profiler based Channel Transfer Function Estimation for 2×2 MIMO Receivers in 5G System Targeting a 500km/h Linear Motor Car

  • Suguru Kuniyoshi;Rie Saotome;Shiho Oshiro;Tomohisa Wada
    • International Journal of Computer Science & Network Security
    • /
    • 제23권9호
    • /
    • pp.8-16
    • /
    • 2023
  • In Japan, high-speed ground transportation service using linear motors at speeds of 500 km/h is scheduled to begin in 2027. To accommodate 5G services in trains, a subcarrier spacing frequency of 30 kHz will be used instead of the typical 15 kHz subcarrier spacing to mitigate Doppler effects in such high-speed transport. Furthermore, to increase the cell size of the 5G mobile system, multiple base station antennas will transmit identical downlink (DL) signals to form an expanded cell size along the train rails. In this situation, the forward and backward antenna signals are Doppler-shifted in opposite directions, respectively, so the receiver in the train may suffer from estimating the exact Channel Transfer Function (CTF) for demodulation. In a previously published paper, we proposed a channel estimator based on Delay and Doppler Profiler (DDP) in a 5G SISO (Single Input Single Output) environment and successfully implemented it in a signal processing simulation system. In this paper, we extend it to 2×2 MIMO (Multiple Input Multiple Output) with spatial multiplexing environment and confirm that the delay and DDP based channel estimator is also effective in 2×2 MIMO environment. Its simulation performance is compared with that of a conventional time-domain linear interpolation estimator. The simulation results show that in a 2×2 MIMO environment, the conventional channel estimator can barely achieve QPSK modulation at speeds below 100 km/h and has poor CNR performance versus SISO. The performance degradation of CNR against DDP SISO is only 6dB to 7dB. And even under severe channel conditions such as 500km/h and 8-path inverse Doppler shift environment, the error rate can be reduced by combining the error with LDPC to reduce the error rate and improve the performance in 2×2 MIMO. QPSK modulation scheme in 2×2 MIMO can be used under severe channel conditions such as 500 km/h and 8-path inverse Doppler shift environment.

수중통신에서 비선형 왜곡과 전력효율을 위한 DFT-spread OFDM 통신 시스템 (DFT-spread OFDM Communication System for the Power Efficiency and Nonlinear Distortion in Underwater Communication)

  • 이우민;유흥균
    • 한국통신학회논문지
    • /
    • 제35권8A호
    • /
    • pp.777-784
    • /
    • 2010
  • 최근 수중 통신에 대한 관심이 급증하고 있으며, 수중 통신을 통한 음성 및 고해상도 영상 데이터와 같은 다양한 데이터 전송의 요구가 증가하고 있다. 수중 음향 통신 시스템의 성능은 수중 채널의 특성에 의해 크게 영향을 받으며, 특히 수중 채널 환경은 다중경로(Multi-path)에 따른 지연확산(delay spread)으로 인하여 데이터 전송 시 인접 심볼 간의 간섭(Inter Symbol interference: ISI)이 발생하여 통신의 성능을 저하시킨다. 본 논문에서는 지연 확산에 강한 성능을 나타내는 OFDM(Orthogonal Frequency Division Multiplexing) 기법을 수중 통신 시스템에 적용하고, OFDM의 CP(Cyclic Prefix)를 이용하여 수중 채널 환경의 다중경로로 인한 지연 확산을 보상한다. 하지만 수중 통신 시스템에 OFDM을 적용할 때, OFDM 시스템이 갖는 고유한 문제인 높은 PAPR(Peak-to-Average Power Ratio)이 발생한다. 그러므로 본 논문에서는 높은 PAPR로 인한 신호의 비선형 왜곡을 피하고 증폭기의 효율을 위하여 DFT-spread OFDM 기법을 적용한다. DFT-spread OFDM 방식은 IFFT 수행 이전에 DFT(discrete Fourier transform) 확산을 수행하여 각각의 병렬 데이터를 모든 부반송파들에 실어 줌으로써 좋은 PAPR 저감 효과를 얻는다. 그러므로 본 논문에서는 OFDM 시스템을 통해 수중 채널에서 지연 확산에 대한 성능 이득을 보이고, 일반적인 OFDM 시스템보다 DFT-spread OFDM이 수중 통신 환경에서 더 적합한 통신 방식임을 시뮬레이션을 통하여 보였다. 그리고 DFT-spread OFDM의 두 가지 자원 분배 방식(Interleaved, Localized)에 따른 성능을 분석하고 수중 통신 환경에서 자원 분배 방식에 따른 성능의 적응성에 대하여 논의하였다. 시뮬레이션 결과를 통해 CP 삽입을 통한 보상후의 BER 성능은 DFT-spread OFDM 방식이 일반 OFDM에 비하여 $10^{-4}$에서 약 5~6dB 정도 좋은 것을 보였으며, 자원 분배 방식에 따른 BER 성능을 비교하였을 때, Interleaved 방식은 Localized 방식에 비하여 $10^{-4}$에서 약 3.5dB 정도 좋은 것을 보였다.

MC-CDMA 방식의 주파수 효율 (Spectral Efficiency of MC-CDMA)

  • 한희구;오성근
    • 대한전자공학회논문지TC
    • /
    • 제43권3호
    • /
    • pp.39-48
    • /
    • 2006
  • 본 논문에서는 다중 반송파 코드 분할 다중 접속 (MC-CDMA: multicarrier code division multiple access) 방식의 주파수 효율을 분석한다. 먼저, 코드 분할 다중화에 사용되는 부반송파 개수와 사용 중인 코드 개수 (부하율), 주파수 영역 채널 계수에 따른 MC-CDMA 방식의 주파수 효율에 대한 일반식을 유도한다. 또한, 전체 부반송파를 여러 개의 그룹으로 분할하여 다중화 복잡도를 줄일 수 있는 다양한 MC-CDMA 전송 방식들의 주파수 효율에 대한 일반식도 유도한다. 이를 통하여, 다중 경로 개수에 따른 채널의 주파수 선택도와 다이버시티 간의 상관관계를 정립하고, 이를 바탕으로 다이버시티를 최대로 얻기 위한 최소의 코드 길이와 최적 부반송파 할당 방법을 도출함으로써, 최소의 길이를 갖는 코드들을 사용하여 주파수 효율을 최대화 할 수 있는 시스템 구조를 제시한다. 모의실험 환경에서의 수치적인 분석을 통하여, 다양한 시스템 구조에 따른 주파수 효율의 특성을 분석하며, 주파수 효율에 결정적인 영향을 주는 시스템 구성 방법과 파라미터들을 도출한다. 마지막으로, 주어진 채널 환경에서 MC-CDMA 방식과 직교 주파수 분할 다중화 (OFDM: orthogonal frequency division multiplexing) 방식의 주파수 효율을 비교함으로써 상호관계를 설정한다.

Simultaneous Wireless Information and Power Transfer in Two-hop OFDM Decode-and-Forward Relay Networks

  • Di, Xiaofei;Xiong, Ke;Zhang, Yu;Qiu, Zhengding
    • KSII Transactions on Internet and Information Systems (TIIS)
    • /
    • 제10권1호
    • /
    • pp.152-167
    • /
    • 2016
  • This paper investigates the simultaneous wireless information and power transfer (SWIPT) for two-hop orthogonal frequency division multiplexing (OFDM) decode-and-forward (DF) relay network, where a relay harvests energy from radio frequency signals transmitted by a source and then uses the harvested energy to assist information transmission from the source to its destination. The power splitting receiver is considered at the relay. To explore the performance limit of such a SWIPT-enabled system, a resource allocation (RA) optimization problem is formulated to maximize the achievable information rate of the system, where the power allocation, the subcarrier pairing and the power splitting factor are jointly optimized. As the problem is non-convex and there is no known solution method, we first decompose it into two separate subproblems and then design an efficient RA algorithm. Simulation results demonstrate that our proposed algorithm can achieve the maximum achievable rate of the system and also show that to achieve a better system performance, the relay node should be deployed near the source in the SWIPT-enabled two-hop OFDM DF relay system, which is very different from that in conventional non-SWIPT system where the relay should be deployed at the midpoint of the line between the source and the destination.

이동 페이딩 채널하의 멀티 스텝 채널 예측기를 이용한 적응 OFDM 시스템의 성능개선 (Performance Improvement on Adaptive OFDM System with a Multi-Step Channel Predictor over Mobile Fading Channels)

  • 안현준;김현동;최상호
    • 한국통신학회논문지
    • /
    • 제31권12A호
    • /
    • pp.1182-1188
    • /
    • 2006
  • 적응 변조 OFDM(Orthogonal Frequency Division Multiplexing) 전송 기법은 각 부반송파의 채널 상태에 따라 변조방식을 적절히 변화시켜 무선 채널의 다중 경로 페이딩에 의해 의한 영향을 최소화하여 시스템의 성능을 증가시키는 방식이다. 시스템이 적응적으로 전송하기위해서는 단말기에서 각 부반송파(subcarrier)별 채널 상태 정보 (Channel State Information : CSI)를 되먹임 채널을 통해 실시간으로 기지국으로 전송해 주어야한다. 하지만, 단말기에서 데이터를 처리할 때 걸리는 시간과, 단말기에서 기지국으로 CSI를 되먹임(feedback) 할 때 걸리는 시간으로 인한 되먹임 지연(feedback delay) d가 발생하게 된다. 이 되먹임 지연은 CSI 정보의 불일치를 발생시켜 적응 OFDM 시스템의 성능저하를 일으킨다. 본 논문에서는 CSI의 되먹임 지연 $d(\geq2)$를 적절히 보상하는 주파수 축 멀티 스탭 채널 예측기를 제안하고 이를 적응 전송 OFDM 시스템에 적용하고 모의실험을 통하여 기존의 OFDM 시스템, 기존의 채널 예측방식과의 성능을 MSE(mean square error), 비트오율(bit error rate : BER) 및 채널용량을 바탕으로 비교한다.