• Korean Journal of Optics and Photonics
• /
• v.14 no.6
• /
• pp.657-662
• /
• 2003

Optimum Hamming apodized acousto-optic 2${\times}$2 add/drop multiplexers, using SiO$_2$ film loaded acoustic waveguide with angular offset to the Ti:LiNbO$_3$ waveguide, were fabricated. The four-port device consists of two input waveguides, a polarization beam splitter (PBS), two polarization conversion/acoustooptic tuning waveguide sections, a second PBS and two output waveguides. Insertion loss <7.1 ㏈ has been obtained and side-lobe of -19 ㏈ for -32 ㎽ RF driving power has been realized. Add/drop performance has been confirmed and a linear tuning rate of 8.1 nm/MHz and a 3 ㏈ spectral width of -1.5 nm were demonstrated.

• Journal of the Korean Geosynthetics Society
• /
• v.10 no.4
• /
• pp.81-92
• /
• 2011

In order to understand evaluation of the seismic stability of a fill dam, we made chambers of 1:100, 1:70, and 1:50 (the ratio of the miniature), considering the law of similarity based on drawings of three representative cross sections. And we measured an increase in acceleration, excess pore water pressure, and vertical/horizontal displacement after applying Hachinohe wave (long period), Ofunato wave (short period), and artificial wave, complying with the domestic standards, in order to evaluate the stability and interaction between the ground, the structure, and fluids based on the measurements. As a result, we could observe that displacement of the target cross section was relatively small compared to the allowed level of 30 cm, ensuring proper stability for an earthquake. Regarding the acceleration measurements, the increase rate was 20% for Hachinohe wave and Ofunato wave but 30% for the artificial wave. With respect to the excess pore water pressure, it was lower than 1 (which is the permissible ratio for liquefaction) ensuring proper stability as well.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.39 no.1
• /
• pp.18-24
• /
• 2002

n this paper, we have fabricated pseudomorphic high electron mobility transistors (PHEMT) with a 0.2 ${\mu}{\textrm}{m}$ wide-head T-shaped gate using electron beam lithography by a dose split method. To make the T-shape gate with gate length of 0.2 ${\mu}{\textrm}{m}$ and gate head size of 1.3 ${\mu}{\textrm}{m}$ we have used triple layer resist structure of PMMA/P(MMA-MAA)/PMMA. The DC characteristics of PHEMT, which has 0.2 ${\mu}{\textrm}{m}$ of gate length, 80 ${\mu}{\textrm}{m}$ of unit gate width and 4 gate fingers, are drain current density of 323 ㎃/mm and maximum transconductance 232 mS/mm at $V_{gs}$ = -1.2V and $V_{ds}$ = 3V. The RF characteristics of the same device are 2.91㏈ of S21 gain and 11.42㏈ of MAG at 40GHz. The current gain cut-off frequency is 63GHz and maximum oscillation frequency is 150GHz, respectively.ively.

• Journal of the Korean Magnetics Society
• /
• v.17 no.1
• /
• pp.38-42
• /
• 2007

The crystallographic and magnetic properties of $KFeO_2$ powder prepared by ball-mill method, have been studied by x-ray diffraction(XRD), $M\"{o}ssbauer$ spectroscopy, and vibrating sample magnetometer(VSM) measurements. The crystal structure of $KFeO_2$ powder at room temperature is determined to be an orthorhombic structure of Pbca with its lattice constants $a_0=5.557{\AA},\;b_0=11.227{\AA},\;c_0=15.890{\AA}$ by Rietveld refinement. $M\"{o}ssbauer$ spectra of $KFeO_2$ were taken at various temperatures ranging from 4.2 to 818 K. The magnetic hyperfine field and isomer shift value at 4.2 K and RT were 519 kOe, 489 kOe and 0.19 mm/s, 0.05 mm/s respectively. The average hyperfine field $H_{hf}(T)$ of the $KFeO_2$ shows a temperature dependence of $[H_{hf}(T)-H_{hf}(0)]/H_{hf}(0)=-0.36(T/T_N)^{5/2}$ for $T/T_N$<0.7, indicative of spin-wave excitation.

• Proceedings of the IEEK Conference
• /
• 2006.06a
• /
• pp.495-498
• /
• 2006

This paper reports a high power 60 GHz push-push oscillator fabricated using 0.12 um metamorphic high electron-mobility transistors (mHEMTs). The devices with a $0.1{\mu}m$ gate-length exhibited good DC and RF characteristics such as a maximum drain current of 700 mA/mm, a peak gm of 660 mS/mm, and an $f_T$ of 170 GHz. By combining two sub-oscillators having $6{\times}50{\mu}m$ periphery mHEMT, the push-push oscillator achieved a 6.3 dBm of output power at 59.5 GHz with more than -35 dBc fundamental suppression. This is one of the highest output power obtained using mHEMT technology without buffer amplifier, and demonstrates the potential of mHEMT technology for cost effective millimeter-wave commercial applications.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.27 no.5
• /
• pp.445-453
• /
• 2016

This paper presents the implementation and design of the 1T-1R wireless HD video streaming systems over 28 GHz mmWave frequency using 3GPP LTE-TDD standard on NI USRP RIO SDR platform. The baseband of the system uses USRP RIO that are stored in Xilinx Kintex-7 chip to implement LTE-TDD transceiver modem, the signal that are transceived from USRP RIO up or down converts to 28 GHz by using self-designed 28 GHz RF transceiver modules and it is finally communicated HD video data through self-designed $4{\times}8$ sub array antennas. It is that communication method between USRP RIO and Host PC use PCI express ${\times}4$ to minimize delay of data to transmit and receive. The implemented system show high error vector magnitude performance above 25.85 dBc and to transceive HD video in experiment environment anywhere.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2004.05b
• /
• pp.472-474
• /
• 2004

In this study, we investigated the characteristics of the input impedance and the gain of a ‘Folded dipole antenna with stub’ by the Method of Moments. The center frequency in this study is 200MHz, the radius of wire is 0.5nm, and the distance between two linear dipoles is 2cm. The inside variation of stub length within 18cm and the outside variation of stub length 4.5cm ive the value of SWR(Standing Wave Ratio) within 3. This means that the impedance matching between the ‘Folded dipole antenna with stub’ and receiver can easily be performed without a supplementary matching circuit.

• Journal of Electrical Engineering and Technology
• /
• v.1 no.1
• /
• pp.101-105
• /
• 2006

In this paper, a disk-type ultrasonic motor using a combination of radial and bending vibration modes is newly designed and fabricated. The characteristics of the test motor are also measured. By means of traveling elastic wave induced at the surface of circumference of the elastic disk, a steel bar in contact with the surface of circumference of the elastic disk bonded onto the piezoelectric ceramic disks is driven in both directions by changing the sine and cosine voltage inputs. The stator of the motor is composed of two sheets of piezoelectric ceramic disks to bond onto both surfaces of an elastic disk, respectively. As a result, the diameter of the elastic body is increased and the resonant frequency is decreased. The resonant frequency of the stator is about 92 kHz, which is composed with piezoelectric ceramic disks of 28 mm in diameter and 2 mm in thickness, and an elastic body of 32 mm in diameter and 2 mm in thickness. A driving voltage of 20 VPP Produces 200 rpm with a torque of 1Nm and an efficiency of about 10%.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.38 no.6
• /
• pp.383-389
• /
• 2001

We report on the design, fabrication, and characterization of 0.35${\mu}{\textrm}{m}$-gate AIGaAs/InGaAs PHEMTs for millimeter-wane applications. The epi-wafer structures were designed using ATLAS for optimum DC and AC characteristics, 0.351m-gate AIGaAs/rnGaAs PHEMTs having different gate widths and number of fingers were fabricated using electron beam lithography Dependence of RF characteristics of PHEMT on gate finger with and number of gate fingers have been investigated. PHEMT haying two 0.35$\times$60${\mu}{\textrm}{m}$$^2$ gate fingers showed the knee voltage, pinch-off voltage, drain saturation current density, and maximum transconductance of 1.2V, -1.5V, 275㎃/mm, and 260.17㎳/mm, respectively. The PHEMT showed fT(equation omitted)(current gain cut-off frequency) of 45㎓ and fmax(maximum oscillation frequency) of 100㎓. S$_{21}$ and MAG of the PHEMT were 3.6dB and 11.15dB, respectively, at 35㎓

• Korean Journal of Veterinary Research
• /
• v.50 no.2
• /
• pp.155-160
• /
• 2010

The objective of this study was to compare wound healing in stomach with $CO_{2}$ laser and scalpel incision by measuring the extent of bleeding, the ease of gastric incision, incision time, degree of adhesion and wound healing degree in dogs. Sixteen healthy dogs were used. Two symmetrical incisions were made in ventral aspect of the stomach between the greater and lesser curvatures were made with scalpel and 0.2 mm spot diameter $CO_{2}$ laser (8W, continuous wave) in sixteen dogs. And then each wound was closed with absorbable suture in a two-layer inverting seromuscular pattern. At 3, 7, 14 and 21 days after initial wounding, each wound was taken for histological observation. On surgery, the extent of bleeding, the ease of incision and incision time showed significant differences between the groups. The $CO_{2}$ laser provided better hemostasis (p < 0.05) and smaller postoperative adhesion compared with the scalpel. However, the scalpel produced faster speed of incision and was easier to handle than the $CO_{2}$ laser (p < 0.05). Although there was no considerable difference between the two groups in histological observation, necrosis and calcium deposit tended to be larger in the $CO_{2}$ laser than in the scalpel.