• Proceedings of the Korean Geotechical Society Conference
• /
• 2004.03b
• /
• pp.757-764
• /
• 2004

This paper deals with the numerical study on the displacement behavior of corner areas in an excavation site. Several corner areas always exist in the excavation site. The corner area has two free surfaces, which may become serious weak point from the viewpoint of structural stability. If the structural reinforcements are not applied adequately in corner areas, significant displacement of retaining wall could occur. What is worse, the collapse of retaining system rarely happens. In this paper, 3D numerical analyses were performed to investigate the effect of the arrangement of diagonal and normal strut. From the analysis results, it is found that the spacing between diagonal strut and normal strut should be less than 4m to avoid excessive displacement due to excavation.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2002.10a
• /
• pp.10-14
• /
• 2002

Structural behavior of high-pressure composite vessels of TYPE 3 (full-wrapped over a seamless aluminum liner) was studied through numerical simulations based on 3D nonlinear finite element method. Under high-pressure loading, a TYPE 3 composite vessel shows material nonlinearity due to elastic-plastic deformation of aluminum liner, and mismatch of deformation at the junction of cylinder and dome causes geometrical nonlinearity. Finite element modeling and analysis technique considering this nonlinearity was presented, and a pressure vessel of 6.8L of internal volume was analyzed. Design specification to satisfy requirements was determined based on analysis results.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2003.04a
• /
• pp.85-91
• /
• 2003

This paper presents a 3D nonlinear analysis with slip in steel-concrete hybrid deck. In this study, it was founded that the limit slip modulus could classify the states of steel-concrete hybrid deck into three parts as full-composite, partial-composite, and non-composite, considering the longitudinal behavior and end-slip as well as the yield load and ultimate load of it. Also, it proved that the stress of lower steel plate at the support was increased, because of frictional forces by reaction forces in the steel-concrete hybrid deck. The end-slip did not occur near the full-composite state, but it was largely increased as the slip modulus decreased. On the basis of the EC 4, the state of steel-concrete hybrid deck classified into brittle behavior and ductile one using the end-slip of it

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2006.04a
• /
• pp.347-354
• /
• 2006

In this paper, we work with steel circular tubes and propose analysis model which can consider local buckling that it has an effect on failure of steel structures and induce the relation between loading and deformation. First of all, in respect to axial symmetry local buckling, which is simplest case, elasto-plastic behavior acting only axial loads is object Therefore, it suggests analysis model for axial symmetry local buckling. And that is explainable the process from increasing internal force to decreasing passing maximum internal force. Besides, we induce the relation between the axial force and axial deformation.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2006.04a
• /
• pp.119-126
• /
• 2006

The elastic budding strength of a GFRP pipe reinforced with ribs was evaluated. The height and thickness of a rib and the spacing between two adjacent ribs were considered as factors affecting tlje budding strength of the pipe. And also, the ratio of the longitudinal stiffness and transverse stiffness was considered as the parameter affecting on the budding strength because GFRP is orthotropic material. Buckling strengths of various GFRP pipe models with different shapes and stiffness ratio were evaluated by FE analyses and a formula to estimate the elastic buckling strength of a rib-reinforced pipe made of orthotropic material was suggested from the regression with FE analysis results. Analysis results show that a rib-reinforced pipe has superior buckling strength to a general flat pipe and the suggested formula estimates accurate buckling strength of the rib-reinforced pipe.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 1991.04a
• /
• pp.84-90
• /
• 1991

Underground structures usually consist of rock masses or concretes which can be cracked or have cracks. This study aims to develop an analysis program which can deal with the effect of discontinuous behavior due to those cracks using the block theory. It is assumed that rock masses form blocks along the discontinuity lines, and deformation within the block is relatively small. The behavior of discontinuity plane of the structures is divided into sliding along the discontinuity plane. separation of discontinuity by tensile force, and degradation of asperity angle of discontinuity plane by external force with sliding of rock Basses. These behaviors are implemented using constitutive relation and relevent load-displacement relation defined through normal and shear stiffnesses. Time varying displacements and block velocities are calculated by explicit time stepping algorithm. The effect of rock supports including rockbolts is also considered, and the tending effects which occurs in relatively thin lining is also considered.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2012.04a
• /
• pp.132-137
• /
• 2012

To enhance the CAE accuracy, the definition of material behavior is one of key influence on the result. In case of plastic material with fiber reinforcement, the anisotropic material behavior should be taken into account to increase of CAE accuracy. BASF has developed an innovative CAE tool, ULTRASIM$^R$, which is capable of generating material models of thermoplastic materials for structural simulation. ULTRASIM$^R$, not only the glass fiber orientation effect, but also the weld line effect, tensile-compression anisotropy, strain rate effect are combined in a non-linear material law, which will be evaluated in a unique failure criterion, thus resulting in an highly accurate CAE approach.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2000.04a
• /
• pp.493-598
• /
• 2000

In the rail facilities, the rail track consists of rail, tie, fastening, accessories and bed. The rail track is largely divided into Ballast Bed Track (BBT) and Concrete Bed Track (CBT) according to the type of bed. In this thesis, among Concrete Bed Track, slab track, which is used for the Japanese high speed railway, is a target of this study. Dynamic analysis by using finite element method are performed where moving train load is periodic function. Then through parametric study, some conclusions are obtained as follows. Cement Asphalt Mortar (CAM) affects contrary mechanical behavior to rail and slab greatly. Therefore, change of CAM spring coefficient should be handled with care. For slab thickness, thin slab is more profitable to reduction of vibration of rail than thick one but mechanical capacity of slab is deteriorated. Improved structural type is proposed, then structural analysis is performed for this one. This type is effective to reduction of vibration of railway system.

• Structural Engineering and Mechanics
• /
• v.30 no.5
• /
• pp.559-576
• /
• 2008

Having established the initial geometry and cable force of a typical three span suspension bridge under permanent load, the additional maximum response of the cable and the stiffening girder due to live load are determined, by means of an analytic procedure, considering the girder first hinged at its ends and then continuous through the main towers. The problem of interaction between the cable and the stiffening girder is examined taking under due consideration the second order effects, whereby, through the analogy to a fictitious tensioned beam under transverse load, a closed -form solution is achieved by means of a simple quadratic equation. It is found that the behavior of the whole system is governed by five simple dimensionless parameters which enable a quick determination of all the relevant design magnitudes of the bridge. Moreover, by introducing these parameters, a set of diagrams is presented, which enable the estimation of the influence of the geometric and loading data on the response and permit its immediate evaluation for preliminary design purposes.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.13 no.1
• /
• pp.88-93
• /
• 2004

In general, a fundamental structural design consideration for an automobile is the overall dynamic behavior in bending and torsion. Dynamic behavior of the automobile are mainly influenced by the structural stiffness of B.I.W.(body-in-white) and the physical property of trim components. In this paper, the modeling techniques for various trim components of middle-sized bus are presented, and the dynamic effects of the trim components on the vibration characteristics of the bus are investigated. The $1^{st}$ torsional frequency is decreased by attaching windshield and backlite to the B.I.W., but the $1^{st}$ vertical bending frequency and the $1^{st}$ lateral bending frequency are increased. The natural frequencies of the bus are decreased by attaching doors and windows. And also, the natural frequencies of the bus are large decreased by attaching seats, instrument panel etc. The study shows that the dynamic characteristics of the bus can be effectively predicted in the initial design stage.