• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.24 no.1
• /
• pp.21-28
• /
• 2000

Although commercial PIV systems have been widely used for the non-intrusive velocity field measurement of fluid flows, they are still under development and have considerable room for improvement. In this study, a single-frame double-exposure PIV system using a high-resolution CCD camera was developed. A pulsed Nd:Yag laser and high-resolution CCD camera were synchronized by a home-made control circuit. In order to resolve the directional ambiguity problem encountered in the single-frame PIV technique, the second particle image was genuinely shifted in the CCD sensor array during the time interval dt. The velocity vector field was determined by calculating the displacement vector at each interrogation window using cross-correlation with 50% overlapping. In order to check the effect of spatial resolution of CCD camera on the accuracy of PIV velocity field measurement, the developed PIV system with three different resolution modes of the CCD camera (512 ${\times}$ 512, lK ${\times}$ IK, 2K ${\times}$ 2K) was applied to a turbulent flow which simulate the Zn plating process of a steel strip. The experimental model consists of a snout and a moving belt. Aluminum flakes about $1{\mu}m$ diameter were used as scattering particles for the liquid flow in the zinc pot and the gas flow above the zinc surface was seeded with atomized olive oil with an average diameter of 1-$3{\mu}m$. Velocity field measurements were carried out at the strip speed $V_s$=1.0 m/s. The 2K ${\times}$ 2K high-resolution PIV technique was significantly superior compared to the smaller pixel resolution PIV system. For the cases of 512 ${\times}$ 512 and 1K ${\times}$ 1K pixel resolution PIV system, it was difficult to get accurate flow structure of viscous flow near the wall and small vortex structure in the region of large velocity gradient.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1995.11a
• /
• pp.261-264
• /
• 1995

The response speed enhancement in picosecond photoconductor made from RF planar magnetron sputtered hydrogenated amorphous germanium thin film is discussed. Pulsed laser annealing technique was used to fabricate the highly conductive ohmic contacts and to remove the shallow deflects in the deposited photoconductive film using the different laser powers. Measured V-I curve showed -5 times bigger conductance in photoconductive gap than the one used by the conventional vacuum annealing method using strip heater.

• Journal of Chest Surgery
• /
• v.24 no.3
• /
• pp.229-244
• /
• 1991

A bioassay technique and organ bath study were performed to analyze the effects of extracellular $Ca^{2+}$ and $Ca^{2+}$-antagonists on endothelium-derived relaxing factor[s][EDRF] released from the endothelial cells of rabbit aorta. Transverse strips with intact endothelium or damaged endothelium were used for the mechanical contraction experiment using organ bath. Long segment including thoracic and abdominal aorta with endothelium [EDRF donor aorta] was perfused with Tyrode solution which was aerated with 95% $O_2-5%$ $CO_2$ mixed gas and kept at 35oC. The perfusate was bioassayed with a transverse strip of thoracic aorta with damaged endothelium. The test strip was contracted with nor-epinephrine and acetylcholine was used to stimulate the release of EDRF from endothelial cells. The results obtained were as follows; 1] The endothelium-dependent relaxation[EDR] induced by acetylcholine was biphasic; an initial rapid relaxation followed by a slow relaxation. 2] EDR induced by acetylcholine was reduced gradually with the decrease in the concentration of extracellular $Ca^{2+}$. The effect of extracellular $Ca^{2+}$ on EDR was more prominent in the late slow relaxation phase. 3] EDR to acetylcholine was not altered by acute exposure to organic $Ca^{2+}$-antagonists. Pretreatment with verapamil to the EDRF donor aortic segment did not alter the magnitude of EDR. 4] Among the inorganic $Ca^{2+}$-antagonists $Mn^{2+}$ and $Cd^{2+}$ did not inhibit EDR, whereas $Co^{2+}$ and $La^{3+}$ inhibited EDR. 5] The inhibitory response of $Co^{2+}$ to EDR developed when infused directly on the test strip. That of $La^{3+}$, however, was evoked when added to solution perfusing the donor aortic segment. The above results suggest that $Ca^{2+}$-antagonists do not affect EDR and the inhibitory effect of $Ca^{2+}$ results from influencing the action of EDRF on vascular smooth muscle, whereas that of $La^{3+}$ results from its action on the release of EDRF from endothelial cells.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.17 no.1
• /
• pp.17-24
• /
• 2003

In this paper, a high efficiency leakage transformer for neon tube is developed to improve its power factor, to reduce its core loss and weight by using a technique of shape optimization and grain direction of non-oriented silicon steel strip. A protection circuit is designed for all types of neon transformer loaded with one or more neon tubes. Whenever the neon tube fails to be started up or comes to the life end, or encounters faults with open-circuits at the output terminals of the neon transformer, the electronic type protection circuit will be initiated to avoid more critical hazards. These neon transformers need a electronic type protection circuit to prevent from current stresses on circuit components by neon tube fail. The input of the transformer is automatically cut on when the abnormal condition occurs, preventing waste of no-load power.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2003.10a
• /
• pp.229-232
• /
• 2003

In the roll forming process, a sheet or strip of metal is continuously and progressively formed into a desired cross-sectional profile by feeding it through a series of forming roll. Accordingly, it is important to maintain the material properties of the initial sheet and deform uniformly during the roll forming. The roll forming process was estimated in consideration of some factors such as material properties, strip thickness, roll diameter, roll velocity, and the deformation of the material that influence the forming length. The hydroforming technology has been recognized as a new technique in manufacturing industry, especially in automotive industry. The formed pipe in used in hydroforming process is manufactured by the roll forming. The formability during hydroforming is very sensitive to the state of pipes which are made by roll forming. Particularly the amount of hardening during roll forming affects the formability. Therefore, it is necessary to design the optimum roll flower to reduce the local hardening. In this paper, optimum roll flower which has uniform strain distribution through sheet width was obtained by comparing strain distribution in various roll flower. Finite element analysis(FEA) is performed to estimate the strain distribution related to hardening by roll forming. A numerical analysis is carried out by SHAPE-RF.

• Computers and Concrete
• /
• v.8 no.6
• /
• pp.717-733
• /
• 2011

Strengthening of reinforced concrete (RC) members against shear that is one of the failure modes especially avoided by using carbon fiber reinforced polymer (CFRP) is widely used technique, which is studied at many experimental studies. However, conducting experimental studies are required more financial resources and laboratory facilities. In addition, along with financial resources, more time is needed in order to carry out comprehensive experimental studies. For these reasons, a verified finite element model that is tested with previous experimental studies can be used for reaching generalized results and investigating parameters that are not studied. For this purpose, previous experimental study results are used and "T" cross-sectioned RC beams strengthened with CFRP strips with insufficient shear strength are modeled by using ANSYS software. First, finite elements modeling of the previously tested RC beams are done, and then the computed results are compared with the experimental ones whether they are matched or not. As a result, the finite element model is verified. Later, analyses of the cases without any test results are done by using the verified model. Optimum CFRP strip spacing is determined with this verified finite element model, and compared with the experimental findings.

• The Korean Journal of Pharmacology
• /
• v.10 no.1 s.15
• /
• pp.47-52
• /
• 1974

The isolated rabbit gall bladder strips were prepared according to the technique described by Amer and Becvar (1969). The strips were placed in a bath containing 100 ml of Locke-Ringer solution maintained at $38^{\circ}C$. Oxygen was continuously bubbled through the solution. The tension of the muscle strip was initially adjusted to 0.7g. The contractile response was measured isometrically by a force-displacement transducer connected to a polygraph. The effect of a number of autonomic drugs were studied for their interaction with caerulein (Prof. V. Erspamer, F.I. 6934 Caerulein, Farmitalia, Italia), a gastrin or CCK.PZ like peptide, on isolated rabbit gall bladder strips. In this preparation caerulein produced contractions of CCK-PZ type, but the relative potency on a weight basis was 40 times that of CCK-PZ. The response of caerulein was not modified by either cholinergic or alpha or beta adrenergic blockade. However, the response of caerulein and of barium on the strips were prevented by papaverine or aminophylline. Isoproterenol, papaverine or aminophylline alone relaxed the preparation whereas caerulein, CCK-PZ, acetylcholine, serotonin, histamine or barium chloride contracted the preparation. In summary, it is concluded that caerulein on the gall bladder strip seems to act independently of the autonomic nervous system and mediated via mechanisms apparently similar to those involved in the action of barium chloride.

• 제어로봇시스템학회:학술대회논문집
• /
• 2005.06a
• /
• pp.1808-1813
• /
• 2005

In this paper, we present the finger tip tactile sensor which can detect contact normal force as well as slip. The developed sensor is made of two different materials, such as polyvinylidene fluoride(PVDF) that is known as piezoelectric polymer and pressure variable resistor ink. In order to detect slip to surface of object, a PVDF strip is arranged along the normal direction in the robot finger tip and the thumb tip. The surface electrode of the PVDF strip is fabricated using silk-screening technique with silver paste. Also a thin flexible force sensor is fabricated in the form of a matrix using pressure variable resistor ink in order to sense the static force. The developed tactile sensor is physically flexible and it can be deformed three-dimensionally to any shape so that it can be placed on anywhere on the curved surface. In addition, we developed a tactile sensing system by miniaturizing the charge amplifier, in order to amplify the small signal from the sensor, and the fast signal processing unit. The sensor system is evaluated experimentally and its effectiveness is validated.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.12 no.4_1
• /
• pp.1-8
• /
• 1992

This paper presents a p-version finite element approach for modeling the stress distribution around a circular hole in a finite strip subjected to membrane and flexural behaviors. Also, same problem with a crack emanating from a perforated tension strip was solved by virtual crack extension method. The p-version of the finite element method based on integrals of Legendre polynomials is shown to perform very well for modeling geometries with very steep stress gradients in the vicinity of a circular cutout. Here, the transfinite mapping technique for circular boundaries was used to avoid the discretization errors. The numerical results from the proposed scheme have a good comparison with those by Nisida, Howland, Newman etc. and the conventional finite element approach.

• Transactions of Materials Processing
• /
• v.23 no.7
• /
• pp.425-430
• /
• 2014

The aim of the current study was to predict the plastic deformation behavior of a heated slab during hot rough rolling. FE-simulations were performed to investigate the metal flow and to locate the position of surface material from the slab through the rough rolling and onto the strip, using a material point tracking technique. In addition, experimental hot rolling trials were conducted where artificial defects were impressed onto a heated slab in order to validate the FE-simulation results. The simulated results show the same tendency of deformation behavior as the experimental measurements. The movement of slab defects from the side surface towards the strip center is directly linked to the extent of lateral spread during the rolling.