• Geomechanics and Engineering
• /
• 제30권2호
• /
• pp.123-138
• /
• 2022

Present study computes the ultimate bearing capacity of an embedded strip footing situated on the rock slope subjected to seismic loading. Influences of embedment depth of strip footing, horizontal seismic acceleration coefficient, rock slope angle, Geological Strength Index, normalized uniaxial compressive strength of rock mass, disturbance factor, and Hoek-Brown material constant are studied in detail. To perform the analysis, the lower bound finite element limit analysis method in combination with the semidefinite programming is utilized. From the results of the present study, it can be found that the magnitude of the bearing capacity factor reduces quite substantially with an increment in the seismic loading. In addition, with the increment in slope angle, further reduction in the value of the bearing capacity factor is observed. On the other hand, with an increment in the embedment depth, an increment in the value of the bearing capacity factor is found. Stress contours are presented to describe the combined failure mechanism of the footing-rock slope system in the presence of static as well as seismic loadings for the different embedment depths.

• 대한토목학회논문집
• /
• 제29권2C호
• /
• pp.71-79
• /
• 2009

본 연구에서는 국내 철도 토공노반 재료로 가장 흔히 사용되는 입도조정쇄석, 화강풍화토, 암버럭-토사 혼합 재료에 대해 평균유효주응력과 축변형률의 함수로 표현되는 회복탄성계수 예측모델을 결정하였다. 회복탄성계수 예측모델은 대표적인 동적물성치인 변형률에 따른 전단탄성계수 감소곡선의 표현과 같이 최대영탄성계수와 정규화 영탄성계수 감소곡선으로 구성된다. 평균유효주응력의 함수로 표현되는 최대영탄성계수의 모델인자는 $A_E$와 $n_E$이고, 비선형 영역의 정규화 영탄성계수 감소곡선은 기준변형률(${\varepsilon}_r$)과 곡률계수(a)를 모델인자로 하는 수정 쌍곡선 모델로 표현된다. 제안된 회복탄성계수 예측모델을 검증하기 위해 3차원 다층탄성해석 프로그램(GEOTRACK)을 이용하여 평택 시험 철도노반의 탄성거동을 평가하였고, 화물열차 및 여객열차가 시험구간을 통과할 때 계측한 노반의 수직 탄성변위와 비교하였다. 현장계측은 자갈도상 아래의 재료가 각각 입도조정쇄석과 양질의 화강풍화토인 두 개소에서 수행되었다. 자갈도상 아래에서 계산된 수직 탄성변위는 대략 0.6mm 이내였고 계측 결과와 잘 일치하였다. 본 연구를 통해 제안된 회복탄성계수 예측모델이 열차하중에 의한 노반의 탄성거동을 적절히 표현하고 있음을 확인하였다.

• 한국정보통신학회:학술대회논문집
• /
• 한국정보통신학회 2012년도 춘계학술대회
• /
• pp.185-187
• /
• 2012

본 논문에서 응용하고자 하는 MR 유체 댐퍼는 상자성(paramagnetic) 입자를 MR 유체 내부에 분산시켜 전류에 따라 발생하는 전자석 원리를 이용하여 MR 댐퍼 내부의 유체의 항복 전달 응력의 변화 실키 수 있는 특징이 있다. 즉, 전류의 세기에 따라 MR 유체 댐퍼 내부의 마찰계수가 달라지는 현상을 이용하는 것이다. 이러한 MR 유체 댐퍼 제어에 사용하고자 하는 MCU는 마이크로칩 사의 dsPIC 칩을 이용하여 성능을 개선하고자 하며 전류제어에는 PWM을 이용하며, 외부 모니터링을 위하여 UART 통신을 이용하여 전체 시스템을 모니터링 하도록 설계하였다. 본 연구에서는 MR 유체 댐퍼와 dsPIC 칩을 사용하여 세탁기의 탈수 과정 시 발생 되는 진동 및 소음을 저감 시키도록 세탁기용 진동 및 소음방지 시스템을 제안하고자 한다.

• Geomechanics and Engineering
• /
• 제7권5호
• /
• pp.495-524
• /
• 2014

To investigate the soil-pile interactive performance under lateral loads, a set of laboratory model tests was conducted on remoulded test bed of soft clay and medium dense sand. Then, a simplified boundary element analysis had been carried out assuming floating pile. In case of soft clay, it has been observed that lateral loads on piles can initiate the formation of a gap, soil heave and the tension crack in the vicinity of the soil surface and the interface, whereas in medium dense sand, a semi-elliptical depression zone can develop. Comparison of test and boundary element results indicates the accuracy of the solution developed. However, in the boundary element analysis, the possible shear stresses likely to be developed at the interface are ignored in order to simplify the existing complex equations. Moreover, it is unable to capture the influence of base restraint in case of a socketed pile. To bridge up this gap and to study the influence of the initial stress state and interface parameters, a field based case-study of laterally-loaded pile in layered soil with socketed tip is explored and modelled using the finite element method. The results of the model have been verified against known field measurements from a case-study. Parametric studies have been conducted to investigate the influence of the coefficient of lateral earth pressure and the interface strength reduction factor on the results of the model.

• Tribology and Lubricants
• /
• 제31권1호
• /
• pp.1-5
• /
• 2015

In this study, we apply an ultrasonic nanocrystal surface modification (UNSM) technique to radial journal bearings (JBs) and disks made of SUJ2 and SCM440, respectively. We investigate frictional properties of untreated and UNSM-treated specimens using a ball-on-disk tester. We construct the Stribeck curve at the boundary, under mixed and full hydrodynamic lubrication conditions for the specimens using friction data obtained from JB tests. The friction at the boundary lubrication condition and the transition period to mixed lubrication condition on the UNSM-treated specimens is reduced, which improves the service life of JBs. The major effects of this reduction in the three lubrication regimes can be explained in the terms of improved mechanical properties and the presence of micro dimples. Moreover, we estimate the friction and fatigue properties of SCM440 specimens using a ball-on-disk specimen under dry and oil-lubricated conditions. Friction test results reveal that the UNSM-treated specimens show lower friction coefficient than the untreated specimens under both dry and oil-lubricated conditions. We evaluate the fatigue properties of SCM440 specimens by calculating the Hertzian stress with respect to the failure cycles. Fatigue tests results also reveal that the UNSM-treated specimens possess a longer fatigue life than the untreated specimens. The improved properties are effective in increasing the energy efficiency of bearings.

• 마이크로전자및패키징학회지
• /
• 제6권2호
• /
• pp.13-21
• /
• 1999

Flip chip assembly directly on organic boards offers miniaturization of package size as well as reduction in interconnection distances resulting in a high performance and cost-competitive Packaging method. This paper describes the investigation of alternative low cost flip-chip mounting processes using electroless Ni/Au bump and anisotropic conductive adhesives/films as an interconnection material on organic boards such as FR-4. As bumps for flip chip, electroless Ni/Au plating was performed and characterized in mechanical and metallurgical point of view. Effect of annealing on Ni bump characteristics informed that the formation of crystalline nickel with $Ni_3$P precipitation above $300^{\circ}C$ causes an increase of hardness and an increase of the intrinsic stress resulting in a reliability limitation. As an interconnection material, modified ACFs composed of nickel conductive fillers for electrical conductor and non-conductive inorganic fillers for modification of film properties such as coefficient of thermal expansion(CTE) and tensile strength were formulated for improved electrical and mechanical properties of ACF interconnection. The thermal fatigue life of ACA/F flip chip on organic board limited by the thermal expansion mismatch between the chip and the board could be increased by a modified ACA/F. Three ACF materials with different CTE values were prepared and bonded between Si chip and FR-4 board for the thermal strain measurement using moire interferometry. The thermal strain of ACF interconnection layer induced by temperature excursion of $80^{\circ}C$ was decreased with decreasing CTEs of ACF materials.

• 대한토목학회논문집
• /
• 제41권5호
• /
• pp.523-531
• /
• 2021

일반적으로 기초는 여러 개의 단일말뚝이 상부 구조체에 의해 연결된 상태로 군말뚝을 의미한다. 하지만, 군말뚝에 상부 하중 재하 시 지반에 작용하는 응력 범위는 단일말뚝에 비해 더 넓은 폭과 깊이로 확장되고, 중복되기 때문에 전체적인 지지력은 감소할 수 있다. 이러한 지지력 감소비를 군말뚝 효율이라 하나 일반적인 말뚝과 지반의 접촉 조건에 따른 영향을 분석한 연구는 부족한 실정이다. 따라서 본 연구에서는 지반 구성 및 군말뚝의 배치, 간격, 지반과 말뚝간의 접촉 특성을 해석 변수로 설정하고, 군말뚝 효율 및 군말뚝을 구성하는 개별말뚝의 거동을 분석하였다. 해석 결과, 지반 종류에 따라 마찰계수 증가 시 군말뚝 효율은 수렴 또는 감소하는 경향을 보였으며, 이를 통해 최적 군말뚝 효율을 분석하였다. 또한, 개별말뚝 분석을 통한 하중 감소비 파악 결과, 군말뚝 내부에 위치한 말뚝의 경우 하중을 상대적으로 적게 받았으며, 이는 내부 지반에 대한 영향인 것으로 판단된다.

• Computers and Concrete
• /
• 제26권6호
• /
• pp.547-563
• /
• 2020

In this paper, the influence of axial compression ratio on the mechanical properties of new type joints of side span of rectangular concrete-filled steel tubular column-H-type steel beam is studied. Two new types of side-span joints of rectangular concrete-filled steel tubular column-H-type steel beam are designed and quasi-static tests of five new type joints with 1:2 scale reduction ratios are performed. The axial compression ratio of joint JD1 is 0.3, 0.4 and 0.5, and the axial compression ratio of joint JD2 is 0.3 and 0.5. In the joint test, different axial forces were applied to the top of the column according to different axial compression ratios, and low-cyclic reciprocating load was applied on the beam. The stress and strain distribution, beam and column deformation, limit state, failure process, failure mechanism, stiffness degradation, ductile deformation and energy dissipation capacity of the joint were measured and analyzed. The results show that: with the increase of axial compression ratio, the ultimate bearing capacity of the joint decreases slightly, the plastic deformation decreases, and the stiffness and ductility decrease. According to the energy dissipation curve of the specimen, the equivalent damping coefficient also increases with the increase of axial compression ratio in a certain range, indicating that the increase of axial compression ratio can improve the seismic performance of the joint to a certain extent. The finite element method is used to simulate the joint test, and the test results are in good agreement with the simulation results.

• Wind and Structures
• /
• 제35권1호
• /
• pp.55-66
• /
• 2022

Tall buildings are often subjected to steady and unsteady forces due to external wind flows. Measurement and mitigation of these forces becomes critical to structural design in engineering applications. Over the last few decades, many approaches such as modification of the external geometry of structures have been investigated to mitigate wind-induced load. One such proven geometric modification involved the rounding of sharp corners. In this work, we systematically analyze the impact of rounded corner radii on the reducing the flow-induced loading on a square cylinder. We perform 3-Dimensional (3D) simulations for high Reynolds number flows (Re=1 × 105) which are more likely to be encountered in practical applications. An Improved Delayed Detached Eddy Simulation (IDDES) method capable of capturing flow accurately at large Reynolds numbers is employed in this study. The IDDES formulation uses a k-ω Shear Stress Transport (SST) model for near-wall modelling that prevents mesh-induced separation of the boundary layer. The effects of these corner modifications are analyzed in terms of the resulting variations in the mean and fluctuating components of the aerodynamic forces compared to a square cylinder with no geometric changes. Plots of the angular distribution of the mean and fluctuating coefficient of pressure along the square cylinder's surface illustrate the effects of corner modifications on the different parts of the cylinder. The windward corner's separation angle was observed to decrease with an increase in radius, resulting in a narrower and longer recirculation region. Furthermore, with an increase in radius, a reduction in the fluctuating lift, mean drag, and fluctuating drag coefficients has been observed.

• 한국조경학회지
• /
• 제35권6호
• /
• pp.29-36
• /
• 2008

This study examined the de-icing agents' stresses on Pinus strobus and Pinus thunbergii by chlorophyll fluorescence analysis. The assumption of this study was that photosynthetic efficiency was changed by de-icing agents applied onto highways in winter by altering the concentration of the de-icier, types of de-icer and leaf surface coating liquid application. The practical purpose of this study was to investigate the de-icing gents stresses on Pinus strobus by the highway area where de-icing agents were used frequently and to discover out minimizing stratages to prevent further damages. or this simulation study, a sample plot was established in Bogae-myeon, Anseong, Gyeonggi-do and Pinus strobus and Pinus thunbergii were planted for the examination in April, 2005. Five types of de-icing agents - NaCl, $CaCl_2$, T product(NS40:low cWoride de-icer type), NaCl+$CaCl_2$ and T product+$CaCl_2$ - were selected and the their concentration was altered to 0%, 5%, and 9%. Five types of de-icing agents were applied to both trees treated by a leaf surface coating liquid and trees not treated by leaf surface coating liquid. For the fluorescence analysis, the leaf surface coating liquid, which was diluted by 10 times, was sprkinkled onto the two tree species three days prior to gathering samples. Sample leaves from the two tree species were gathered at 10 o'clock in the morning of mid-August, 2006 and brought to the laboratory within three hours to be dipped in different concentrations (0%, 5%, or 9%) of the five de-icing agents for two minutes. Then the eaves were placed on the filter paper dipped in each solution on a petri dish, sealed with polyethylene film and kept in a growth chamber at $22^{\circ}C$ for 72 hours. Out of the growth chamber, the leaves were treated with a chorophyll fluorescence reaction analyzer for 30 minutes to measure the initial light acceptance rate(Fo), maximum light acceptance ate(Fv/Fm), light acceptance usage(F' q/F' m) and optical electron delivery coefficient(qP). As a result, Pinus strobus' initial light acceptance rate(Fo) decreased as T product and NaCl increased in concentration, and $Cal_2$ did not reduce much with the eaf surface coating liquid application. Maximum light acceptance rate(Fv/Fm) and light acceptance usage(F' q/F' m) decreased sharply as T product and NaCl increased in concentration and NaCl+$CaCl_2$ and T product+$CaCl_2$ did not reduce much with leaf surface coating liquid application. Optical electrons delivery coefficient (qP) decreased as T product increased in concentration on trees without the leaf surface coating liquid application and all other de-icing agents did not show much reduction. As for Pinus thunbergii, the initial light acceptance rate(Fo) decreased as T product increased in concentration, but the maximum light acceptance rate(Fv/Fm) was not reduced much by changes in concentration. light acceptance usage(F' q/F' m) decreased as NaCl increased in concentration and optical electron delivery coefficient(qP) decreased as NaCl increased in concentration in both with and without leaf surface coating liquid application. In conclusion, it was possible to plant Pinus strobus if spraying leaf surface coating liquid or cleaning deicing salt to prevent the damage caused by deicing agents was more economical than replacing the trees. If not, it was better to plant Pinus thunbergii. Another way to decrease the deicing gents stresses of landscape plants would be planting the trees further away from the roads even though it might take longer period to display its planting functions.