• Journal of Ocean Engineering and Technology
• /
• v.21 no.1 s.74
• /
• pp.64-68
• /
• 2007

Recently, there has been considerable research in the field of application of Laser-Arc hybrid welding for superstructures, such as ship-structures, transport vehicles etc. However, the study on heat distribution and welding residual stress of hybrid weld by numerical simulation leaves much to be desired. Therefore, in this study, an optimized welding condition and numerical simulation for hybrid welding, using previous numerical analysis to calculate the heat source for hybrid welding, has been analyzed. For this purpose, fundamental welding phenomena of the hybrid process, using Laser and, is investigated. In order to calculate temperature and residual stress distribution in hybrid welds, a finite element heat source model is developed on the basis of experimental results and characteristics of temperature. Residual stress distribution in hybrid welds are understood from the result of simulation, and compared with the experimental values.

• Journal of Welding and Joining
• /
• v.7 no.2
• /
• pp.49-59
• /
• 1989

The effect of non-metallic inclusions on the HAZ hydrogen induced cracking was investigated. Quench and temper high tensile strength steels containing various sulphur contents were employed. The sulphur contents range between 0.007% and 0.040%. Non-metallic inclusions were mainly MnS type sylphide and Mn-Al-Si type. The sensitivity of HAZ delayed cracking was evaluated by implant testing. Diffusible hydrogen content was varied by controlling the moisture absorbing condition of manual arc welding electrodes. The one was asreceived condition, the other was dipping the electrodes in the water for ten minutes. The main results obtained were as follows; 1) The results of implant test showed that critical stress increased with increasing S content up to 0.013%. But steel containing 0.040%S showed lower critical stress than that of 0.013% S. These result suggest that there will be optimum S content to prevent HAZ delayed cracking of high strength steels. 2) Under the lower D.H.C. level, critical stress was increased with rolling reduction, but higher D.H.C. level, effect of rolling reduction was not recognized.

• Safety and Health at Work
• /
• v.1 no.1
• /
• pp.43-50
• /
• 2010

Objectives: The objective of this study was to investigate the effect of chain installation condition on stress distribution that could eventually cause disastrous failure from sudden deformation and geometric rupture. Methods: Fractographic method used for the failed chain indicates that over-stress was considered as the root cause of failure. 3D modeling and finite element analysis for the chain, used in a crane hook, were performed with a three-dimensional interactive application program, CATIA, commercial finite element analysis and computational fluid dynamic software, ANSYS. Results: The results showed that the state of stress was changed depending on the initial position of the chain that was installed in the hook. Especially, the magnitude of the stress was strongly affected by the bending forces, which are 2.5 times greater (under the simulation condition currently investigated) than that from the plain tensile load. Also, it was noted that the change of load state is strongly related to the failure of parts. The chain can hold an ultimate load of about 8 tons with only the tensile load acting on it. Conclusion: The conclusions of this research clearly showed that a reduction of the loss from similar incidents can be achieved when an operator properly handles the installation of the chain.

• Smart Structures and Systems
• /
• v.23 no.1
• /
• pp.31-44
• /
• 2019

The present study investigate the compressive stress, shear stress, tensile stress, vertical electrical displacement and horizontal electrical displacement induced due to a load moving with uniform velocity on the free rough surface of an irregular transversely isotropic functionally graded piezoelectric material (FGPM) substrate. The closed form expressions ofsaid induced stresses and electrical displacements for both electrically open condition and electrically short condition have been deduced. The influence of various affecting parameters viz. maximum depth of irregularity, irregularity factor, parameter of functionally gradedness, frictional coefficient of the rough upper surface, piezoelectricity/dielectricity on said induced stresses and electrical displacements have been examined through numerical computation and graphical illustration for both electrically open and short conditions. The comparative analysis on the influence of electrically open and short conditions as well as presence and absence of piezoelectricity on the induced stresses and induced electrical displacements due to a moving load serve as the salient features of the present study. Moreover, some important peculiarities have also been traced out by means of graphs.

• Journal of the Society of Naval Architects of Korea
• /
• v.57 no.5
• /
• pp.254-261
• /
• 2020

The structural safety of hydraulic winch drum and the gears are estimated by the Finite Element Analysis (FEA) and the winch operation experiment. The mesh convergence test is performed and the applied force is the pressure on the drum converted from the rope tension in working condition. The stress of the drum calculated from the strain values of the winch operation experiment shows the agreement with that from the FEA. Most stress values are under the yield strength except for the small hole made for the wire rope fixation. The life of bearings in the drum is calculated using the life prediction formula with the reaction forces from the operation load. One of the two ball bearings shows the short life for impact condition, yet the real prototype winch system shows more life than the numerical value.

• Korean Journal of Culture and Social Issue
• /
• v.28 no.2
• /
• pp.83-106
• /
• 2022

The current study examined the effects of the type and context of self-talk on task performance, task-post emotion, and perceived stress. Participants were 100 undergraduates in Busan. Participants were randomly assigned to one of four the experimental groups that were set by combining the narrative condition (the first-person versus non-first-person) to the content condition (self-reinforcing versus self-critic) to measure their pre and post intervention responses. For the analysis, we performed two-ways analysis of variance using the difference value of dependent variables comparing the pre and post-intervention. As a result of the analysis, we found that content condition of self-talk significantly influenced task performance, task-related confidence, emotion response, and perceived stress. That is, the self-reinforcement self-talk group showed better performance, higher task-related confidence, more positive emotion, lower negative emotion and less perceived stress than the self-critic self-talk group. The contents conditions of self-talk interacted with the narrative condition of self-talk to predict perceived stress, indicating that only non-first person/self-reinforceing self-talk group showed reduced levels of perceived stress.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.21 no.10
• /
• pp.1571-1579
• /
• 1997

The development of a new material which should be continuously use under severe environment of very high temperature has been urgently requested. For the development of such super-heat resistant materials, the main problem is not only to make the superior thermal barrier properties but also to actively release thermal stress. So, a new concept of functionally graded material(FGM) has been proposed to overcome this problem. A composition and microstructure of FGM are varied continuously from place to place in ways designed to provide it with the maximum function of mitigating the induced thermal stress. So, FGM can be applied in the aerospace, the electronic and the medical field, etc.. In this study, thermal stress analysis of sintering PSZ/NiCrAlY graded material was conducted theoretically using a finite-element program. The temperature condition was sintering temperature assuming a cooling-down process up to room temperature. Fracture damage mechanism was anlayzed by the parameters of residual stress. It could be known that FGM provided with the function of mitigating the induced thermal stress.

• Journal of the Korean Society of Food Culture
• /
• v.15 no.5
• /
• pp.387-397
• /
• 2000

A survey was carried out to investigate relation between life stress and nutrient intake status in female university students. It was represented that increasing trends of food intake under the stress condition and preference taste was sweet and hot in female students. The female students thought that food intake for coping with stress was produced negative results and they perceived the relation between stress and their health problem. There was a positive correlation between stress level and the change of food intake in female students statistically(p<0.01). They had higher stress in future prospect, academic problem, friend relationship, personality and family relationship. The average calorie intake of female university students was 1553.06kcal(77.65% of RDA). The intake of protein, calcium and iron were quite less than the RDA, whereas the intake of phosphate, vitamin A, $B_2$, C, niacin were more than the RDA. In changes of nutrient intake under the stress conditions, the higher stress group had decreased intake of calcium, iron, vitamin $B_1,\;B_2$, C than the lower stress group(p<0.05).

• International Journal of Safety
• /
• v.2 no.1
• /
• pp.1-6
• /
• 2003

In this paper, several different fracture criteria using the Eftis and Subramanian's stress solutions [1] are compared with the printed experimental results under different loading conditions. The analytical results of using the solution with non-singular term show better than without non-singular in comparison with the experimental data. And maximum tangential stress criterion (MTS) and maximum tangential strain energy density criterion (MTSE) can get useful results for several loading conditions.

• Tribology and Lubricants
• /
• v.16 no.4
• /
• pp.289-294
• /
• 2000

This paper present the contact stresses, which considers the shear stress at the cam and follower interface in the direct acting type valve train system of a high speed engine. To determine the contact condition, the normal contact forces are calculated by using the lumped mass dynamic modeling. The line contact is considered between the cam and follower interface. The variations of dynamic stresses are presented as a function of camshaft rotational angle. Also the effects of various design parameters are investigated.