• 한국자동차공학회논문집
• /
• 제4권1호
• /
• pp.55-62
• /
• 1996

The dynamic photoelastic technique has been utilized to investigate the possibility of relieving the large local singular stresses which are induce in the corner of a right angled indenter. The indenter compresses a semi-infinite body dynamically with an impact load applied on the top of the indenter. The effect of geometric changes to the indenter in terms of the diameter (d) and the location (ℓ) of the notch on the relieving of the dynamic contact stresses are investigated. A multi-spark-high speed camera with twelve sparks was used to take dynamic photographs. The contact singular stresses were found to be released by introducing the relief notch along the indenter. The optimal location and geometry of the relief notch need further experimental investigation.

• 보건의료산업학회지
• /
• 제7권2호
• /
• pp.135-148
• /
• 2013

The aim of this study is to analyze affecting factor on the job finding stress of university students majoring occupational therapy. We collected data for 7days from 12 to 19 July, 2012. This study was surveyed 270 university students majoring occupational therapy was located in the Pusan and South Kyungnam region. It was found that mean score of the job find stress was $2.12{\pm}0.57$. There was statistically significant difference in the physical symptom, depression, anxiety and sub-domain on the job finding stress by gender, age, the economic status, region of birth, the state of employment, employment determinants, job finding stress relief, advice for job finding(p<0.05). From the multiple regression analysis, it was found that affecting factor on the job finding stress was personal characteristics, job related characteristics, stress relief characteristics, physical symptom, depression, anxiety which was statistically significant difference(p<0.05). As a result, we could know that they must relieve the physical symptom, depression and anxiety for lowering job finding stress of university student majoring occupational student.

• 한국추진공학회지
• /
• 제1권1호
• /
• pp.104-110
• /
• 1997

고강도 알루미늄 합금 링롤재의 급냉, 링 팽창(expansion) 및 링 압축(compression) 응력제거처리 후 잔류응력을 예측하기 위하여 2차원 축대칭 열해석 및 탄소성 해석을 수행하였다. 급냉 및 응력제거처리 후 2단 과시효 처리(T73)된 링롤재에 대하여 3단계 절단법(Three step sectioning method)을 적용하여 링롤재의 두께에 따른 잔류응력 분포를 측정하였으며, 측정결과를 급냉 및 응력제거처리후 잔류응력 해석결과와 비교분석하였다. 링의 급냉후 원주 및 축방향의 잔류응력 해석값은 T73후 측정값과 비슷한 경향을 보였으며, 링의 내면과 외면에서 압축응력을 나타내었고 중심에서 인장응력을 나타내었다. 잔류응력은 링 팽창(T7351) 및 링 압축(T7352) 적용후 T73에 비해 현저히 감소하였으며, 축방향의 제거 효과가 원주방향보다 우수하게 나타났다. 또한 링 압축에 의한 제거효과가 링 팽창보다 크게 나타났다. 링롤재의 응력제거처리는 제거 효과 및 실용성 측면에서 링 압축 공정이 유리하며, 치수제어 및 장비용량 측면에서 링 팽창 공정이 유리하다는 결론을 얻었다.

• 한국강구조학회 논문집
• /
• 제25권5호
• /
• pp.451-461
• /
• 2013

강교량에는 외력에 대해 저항하는 부재의 좌굴 등의 변형을 구속시키기 위한 여러 상세부들이 존재한다. 이들 상세부는 상호 교차하는 부재들로 구성되고 제작의 용이성, 용접결함의 원천적 배제 및 응력집중을 완화시키기 위해 스켈럽을 이용해 왔다. 본 연구에서는 교차부에 발생되는 응력집중으로 상세범주 D등급 이하를 갖게 되는 강교량 상세부의 피로저항 능력을 상세범주 C등급 이상으로 개선시키는 방안으로 응력완화홀(SRH)을 제안하였다. 적절한 크기 및 위치의 SRH 효과를 확인하고 이를 강바닥판교의 U-rib와 가로보 교차부에 작용시켜 SRH에 의한 피로저항능력 개선 가능성을 확인하였다.

• 한국광학회지
• /
• 제32권5호
• /
• pp.230-234
• /
• 2021

열응력 완화 기술은 고출력 레이저 다이오드의 빔의 품질과 안정성을 향상시키기 위한 주요 요소기술로 큰 주목을 받고 있다. 본 연구에서는 레이저 다이오드 바(LD-bar) chip-on-submount (CoS)에 발생하는 열응력 분포 양상을 SolidWorks 소프트웨어를 사용하여 해석하고, 마이크로-홈 구조 도입에 따라 열응력 완화에 미치는 영향을 체계적으로 분석한다. 마이크로-홈 구조는 누적응력을 차단하는 효과가 있는 반면, 열흐름을 방해하는 역기능도 있으므로, 시스템 구조와 방열금속판 두께에 따라 홈 깊이를 최적화할 필요가 있다. 간단히 도입된 예시구조에 대하여, LD-bar CoS의 칩 홀더 금속판에 도입하는 마이크로-홈 구조 최적화를 통해 칩 전면부 표면 응력을 마이크로-홈 구조가 없는 경우의 약 1/5 정도로 낮추었다. 향후 초고출력 시스템에서 방열을 위한 열저항과 광출력 빔크기를 최소한으로 유지하면서, 열응력을 효과적으로 완화시키는 구조로 활용이 기대된다.

• 한국생산제조학회지
• /
• 제22권5호
• /
• pp.859-864
• /
• 2013

Creation of a stress relief groove is a fairly simple yet high-performance method. During the application of this method, it is important to consider the location and size of the groove in order to achieve better performance. Consequently, this research proposes an approach for optimizing the application of the stress relief groove method to a press-fitted assembly. In a boss design, the position and diameter of the groove are configured as design variables and the design of experiments is applied. Based on this information, a 3D model is built and analyzed using the finite element analysis software ABAQUS. Meta-models are created using back-propagation neural networks. Then, deterministic optimization results obtained from a genetic algorithm are compared with the results of the finite element analysis. The temperature sensitivity of the optimized model is analyzed, and finally, reliability-based design optimization is conducted for enhancing the design quality.

• 대한기계학회논문집A
• /
• 제20권7호
• /
• pp.2097-2107
• /
• 1996

The dynamic photoelastic technique had been utilized to investigate the possibillity of relieving the large local singular stresses induced at the corner of a right- angle- indenter. The indenter compressed a semi-infinite body dynamically with an impact load applied on the top of the indenter. The effects of the geometric changes of the indenter in terms of the diameter (d) and the location (1) of the stress relieving notch on the behavior of the dynamic contact stresses were investigated. The influence of stress relieving notches positioned along the edge of the semi-infinite body on the dynamic contact stresses were also studied by changing the diameter (D) and the location (L) of the notch. A multi-speak-high speed camera with twelve sparks were used to take photographs of full field dynamic isochromatic fringe patterns. The contact singular stresses were found to be released significantly by the stress relief notches both along the indenter and the edge of the semi-infinite body. The optimal position and geometry of the stress relieving notches were obtained with the aid of limited experimental results.

• 대한기계학회논문집A
• /
• 제33권1호
• /
• pp.72-81
• /
• 2009

This paper provides simulational round robin test results for welding residual stress prediction of safety/relief nozzle. To quantify the welding variables and define the recommendation for prediction and determination of welding residual stress, 6 partners in 5 institutes participated in round robin test. It is concluded that compressive axial and hoop residual stress occurs in dissimilar metal weld and pre-existing residual stress distribution in dissimilar metal weld was affected by similar metal weld due to short length of safe end. Although the reason for the deviation among the results was not pursued further, the effect of several key elements of FE analyses on welding residual stress was investigated in this paper.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2009년도 춘계 학술발표회
• /
• pp.1125-1132
• /
• 2009

The theory and a probe of the pilot hole wall deformation method, which is a 3-dimensional stress measurement method based on the stress relief principle, were developed. A pilot hole is drilled from the bottom of a borehole and the stress measurement probe is inserted into the pilot hole. The borehole is advanced as the overcoring and the changes in the radius of the pilot hole in three directions and in the axial lengths between the borehole bottom and the pilot hole wall along four axial lines are measured by cantilever type-displacement sensors. The differences between the displacements by the elastic stress analysis and those measured by using the probe were within 3% in the uniaxial compression test of an acrylic resin plate having a hole.

• 한국기계가공학회지
• /
• 제17권3호
• /
• pp.16-21
• /
• 2018

The effect of heat treatment on the fatigue crack growth behavior in welded joints between the heat-affected zone (HAZ) of SA 508 Cl.3 low-alloy steel and HAZ of AISI 316L stainless steel is investigated. When the crack propagates across SA 508 Cl.3 or AISI 316L SS and HAZ into the weldment, the fatigue crack growth rate (FCGR) in the HAZ region does not change or decrease despite the increase in stress intensity factor ${\Delta}K$. The residual stress at the HAZ region is more compressive than that at the base Δ materials and weldment. The effect of the welding residual stress on the crack growth behavior is determined by performing a residual stress relief heat treatment at $650^{\circ}C$ for 1h and subsequent furnace cooling. The FCG behavior in the HAZ region in the as-welded specimen and the residual stress relief heat-treated specimen is discussed in terms of the welding residual stress.