• Steel and Composite Structures
• /
• v.21 no.5
• /
• pp.1031-1043
• /
• 2016

Optimization of the construction scheme of the cable-strut tensile structure based on error sensitivity analysis is studied in this paper. First, the element length was extracted as a fundamental variable, and the relationship between element length change and element internal force was established. By setting all pre-stresses in active cables to zero, the equation between the pre-stress deviation in the passive cables and the element length error was obtained to analyze and evaluate the error effects under different construction schemes. Afterwards, based on the probability statistics theory, the mathematical model of element length error is set up. The statistical features of the pre-stress deviation were achieved. Finally, a cable-strut tensile structure model with a diameter of 5.0 m was fabricated. The element length errors are simulated by adjusting the element length, and each member in one symmetrical unit was elongated by 3 mm to explore the error sensitivity of each type of element. The numerical analysis of error sensitivity was also carried out by the FEA model in ANSYS software, where the element length change was simulated by implementing appropriate temperature changes. The theoretical analysis and experimental results both indicated that different elements had different error sensitivities. Likewise, different construction schemes had different construction precisions, and the optimal construction scheme should be chosen for the real construction projects to achieve lower error effects, lower cost and greater convenience.

• Journal of the Korean Society of Safety
• /
• v.34 no.1
• /
• pp.76-81
• /
• 2019

In this study, the causes of human error were identified through the survey of the drivers of the three organizations: Seoul Metro, Seoul Metropolitan Rapid Transit Corporation, and Korail. It was started with the aim of finding and eliciting causes in various directions including human factors, job factors, and environmental factors. The Cronbach alpha value was 0.95 for the reliability significance of the stress-induced factors in the operational area. The significance probability for organisational factors was shown to be 0.82, and the significance of the sub-accident experience and the driving skill factors in operation was 0.81 In addition, the analysis results showed that stress-induced in the field of driving is higher than the human factors in the reliability analysis. The results of the analysis confirmed that the reliability of the organizational and operational stress-induced factors was higher than other causes. In order to reduce urban railroad accidents, this paper suggests a method for operating safe urban railroad through the minimization human errors.

• Journal of the Korean Society of Mechanical Technology
• /
• v.20 no.6
• /
• pp.924-928
• /
• 2018

The objective of this study is to solve a problem that is occurred during the spline machining of tubular shaft yoke in both side IMS module. In order to simulate the problem, the movement direction of upper die was set as standard case and error case. The material of tubular shaft yoke was set to S20C as refer to the analysis library. The movement directions of upper die were separated with standard case and error case. The error case was set to simulate the problem in the spline machining of tubular shaft yoke. In order to solve the problem, the outer radius of upper die were modelled from 9.40mm to 9.44mm. The simulation results were analyzed and compared in terms of effective stress, metal flow line and folding phenomena characteristics. In case of the outer radius of upper die was 9.42mm, it was observed a relatively uniform effective stress distribution and had a straight metal flow line.

• Journal of the Korean Society of Safety
• /
• v.19 no.3 s.67
• /
• pp.118-123
• /
• 2004

The more the lift environment eastern idea, culture, factory automation system and information technology complicates, the more the various human error brings about. It brings about all kind of accidents and occupational diseases. Also the death and sickness or injury by psychological stress among the human error has increased every year. Therefore this paper describes the Korean lift change unit model through statistical testing with the proposed life change unit factors on the married workers living the middle area. The proposed model can be simply used in order to minimize the industrial accident and human error in real fields. Finally, the result will be helpful for the better safety management.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2002.10a
• /
• pp.615-622
• /
• 2002

In this paper, the modification of double projection method for the adaptive analysis of Element-free Galerkin(EFG) method were proposed. As results of the double projection method, the smoothed error profile that is adequate for adaptive analysis was obtained by re-projection of error that means the differences of EFG stress and projected stress. However, it was found that the efficiency of double projection method is degraded as increase of the numerical integration order. Since, the iterative refinement to single step error estimation made the same effect as increasing of integration order, the application of the iterative refinement base on double projection method could be produced the inadequately refined analysis model. To overcome this defect, a modified scheme of double projection were proposed. In the numerical example, the results did not show degradation of double projection effect in iterative refinement and the efficiency of proposed scheme were proved.

• Journal of the Korean Society of Safety
• /
• v.11 no.3
• /
• pp.10-19
• /
• 1996

Grinding temperature and thermal deformation(dimensional error) are studied theoretically and experimentally. The propose of this research is clarified loading phenomena and residual stress In order to guide nozzle's efficiency. The main results to be obtained are as follows ; 1) When grinding condition Is high efficient grinding, FEM program is developed about grinding heat and dimensional error. 2) Thermal deformation depend on temperature distribution is in good agreement with experimental results in case of little grinding energy flux but is comparatively in good agreement with in case of large (3.5$\times$10$^{6}$ J/m). 3) In terms of high efficient grinding at field(table speed 4m/min), grinding fluid (dilution 5/100) obtained a good workpiece quality and decreased a grinding temperature. 4) A surface roughness, dimensional error, residual stress and loading phenomena with guide nozzle are decreased and these results obtained a good workpiece quality.

• Proceedings of the KSR Conference
• /
• 2007.11a
• /
• pp.646-649
• /
• 2007

Although the up-to-date(high) technique is developing and automating in many fields, the center of the all fields is closely connected with the human resource. Also, the railway driver is required to have both high technique and high level of mental work. Therefore, this research will grasp the types of the railway driver groups through railway driver's task stress analyze(JCQ and Job Content Questionnaire), and then analyze the human errors which the types can occur. Finally, this research will propose the way to reduce the human errors.

• Proceedings of the KSME Conference
• /
• 2001.06a
• /
• pp.262-267
• /
• 2001

In this study, the Reliability of degraded steam turbine blade was evaluated using the limited fatigue data. The statistical estimation of limited fatigue data implies that some unknown uncertainties which may be involved in fatigue reliability analysis. Therefore, an appropriate distribution in the fatigue strength was determined by the characteristic distribution - linear correlation coefficient, fatigue physics, error parameter. 3-parameter Weibull distribution is the most appropriate distribution to assume for infinite region. The load applied on the blade is mainly tensile. The maximum Von-Mises stress is 219.4 MPa at the steady state service condition. The failure probability($F_p$) derived from the strength-stress interference model using Monte carlo simulation under variable service condition is 0.25% at the 99.99% confidence level.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2003.10a
• /
• pp.317-324
• /
• 2003

Kriging interpolation is one of the gennerally used interpolation techniques in Geostatics field. This research refers to the contents about important experimental variogram and the study of theoretical variogram and formulation of Kriging interpolation. Kriging interpolation is applied as interpolation for stress smoothing in finite element method. Posteriori error estimation which makes use of stress smoothing from the FEM is very important part, we try to make practical application of surface regeneration ability from Kriging interpolation. This research is necessary preceding one in order to materialize adaptive FTM through posteriori error estimation. For instance, find the estimate value and estimate the propriety through various theoretical variogram models of the reference analyzed from tensional L-shape domain. It also provides possibility of the Kriging interpolation through comparing to existing Least square method as well.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2002.04a
• /
• pp.69-76
• /
• 2002

In this paper, several improved Element-Free Galerkin (EFG) methods containing singular expression in their approximation functions are compared one another through a patch test with near-tip field. Intrinsic enrichments that expand the basis function partially and fully with known near-tip displacement field and a local enrichment using auxiliary supports based on the partition of unity concept are examined by evaluating a relative stress norm error and the stress intensity factor. Some numerical examinations graphically show that how the size of compact support, dilation parameter and the diffraction parameter can affect the accuracy of the improved EFG methods in the error and the stress intensity factor.