• Journal of Advanced Marine Engineering and Technology
• /
• 제22권5호
• /
• pp.595-608
• /
• 1998

A diffuser an important equipment to change kinetic energy into pressure energy has been studied for a long time. Though experimental and theoretical researches habe been done the understanding of energy transfer and detailed mechanism of energy dissipation is unclear. As far as numerical prediction of diffuser flows are concerned various numerical studies have also been done. On the contrary many turbulence models have constraint to the applicability of diffuser-like flows with expansion and streamline curvature. In order to obtain the reliability of k-$\varepsilon$ turbulence model modified combination turbulence models composed of the anisotropic k-$\varepsilon$model modified combination turbulence models composed of the anisotropic k-$\varepsilon$ model with Hanjalic-Launder's preferential normal strain and Pope's vortex stretching mechanism are proposed. The results of the present proposed models prove the fact that the coefficient of pressure and the shear stress are well predicted at the diffuser flow.

• 동력기계공학회지
• /
• 제3권3호
• /
• pp.54-59
• /
• 1999

The purpose of the present study was to develop the numerical method for predicting the on-design and off-design performance of multistage axial-flow compressors. The aerodynamic properties in blade rows were analyzed by incorporating the streamline curvature method as a quasi 3D analysis with the imperical modeling of exit flow angle and loss coefficients. The present calculation procedure has been tested by applying to 5-stage compressors and good agreement with experiments has been found. The detail analysis of aerodynamic performances has been done on the compression part of the bench-scaled gas turbine engines. The predicted performance map at the variable speedline and flow rates could be used as a guide of the engine operation.

• 설비공학논문집
• /
• 제1권1호
• /
• pp.87-96
• /
• 1989

Flows through impellers of centrifugal compressors are calculated by a streamline curvature method. A method for the exit boundary condition is suggested in the present paper. Flow angles are assumed to be deviated from the blade angle parabolically. The maximum deviation is adjusted for the whole angular momentum to balance with the empirically estimated value by using Stanitz' slip-factor. The present method is verified to reasonably simulate flows through the impeller, when the 3-dimensionality of the flow is not strong. It is also shown that the method can be applied for the design of the splitter in the impeller.

• Journal of Advanced Marine Engineering and Technology
• /
• 제23권2호
• /
• pp.216-225
• /
• 1999

Four turbulent $k-{varepsilon}$models(i.e standard model modified models with streamline curvature modification and/or preferential dissipation modification) are applied in order to analyze the tur-bulent flow of wall-attaching offset jet. The upwind numerical scheme was adopted in the present analyses. The streamline curvature modification results in slightly better prediction while the preferential dissipation modification does not. The obtained analytic results will be used as refer-ences for further study regarding Reynolds stress model. In addition this paper introduced a method of increasing nozzle outlet velocity gradually for numercal convergence. Even though the method was simple it was efficient in view of convergent speed CPU running time computer memory storage programming etc.

• 한국수자원학회:학술대회논문집
• /
• 한국수자원학회 2005년도 학술발표회(1)
• /
• pp.581-582
• /
• 2005

• 대한기계학회논문집
• /
• 제14권2호
• /
• pp.440-452
• /
• 1990

Comprehensive numberical computations have been made for four turbulent swirling jets with and without recirculation to critically evaluate the accuracy and universality of several exising turbulence models as well as of the modified k-.epsilon. model proposed in the present study. A numerical scheme based on the full Navier-Stoke equations ha been developed and used for this purpose. Inlet conditions are given by experiments, whenever possible, to minimize the error due to incorrect initial conditions. The standard k-.epsilon. model performs well for the strongly swirling jets with recirculation while it underpredicts the influence of swirl for weakly swirling jets. Rodi's swirl correction and algebraic stress model do not exhibit universality for the swirling jets. The present modified k-.epsilon. model derived from algebraic stress model accounts for anisotropy and streamline curvature effect on turbulence. This model performs consistently better than others for all cases. It may be because these flows have a strong dependence of stresses on the local strain of the mean flow. The predictions of truculence intensities indicate that this model successfully reflect the curvature effect in swirling jets, i.e. the stabilizing and destabilizing effects of swirl on turbulence transport.

• 한국자동차공학회논문집
• /
• 제4권4호
• /
• pp.118-129
• /
• 1996

In this study, three dimensional flow analysis in a HVAC duct was performed computationally using various turbulence models and compared numerical predictions such as outlet flow split, surface pressure distribution along the duct to experimental data. It's well known that accuracy of computational predictions of flow heavily dependent on turbulent models and discritization method. Therefore, in this work, to assess the ability of turbulent models to predict characteristics of duct flow, three kinds of models, namely standard $k-\varepsilon$, RNG $k-\varepsilon$ and modified $k-\varepsilon$, containing parameter for the effect of streamline curvature were employed and validated one another by comparing with experimental data. In results, modified $k-\varepsilon$ turbulence model allows a successful prediction of static pressure distribution particulary at around strong curvature but little improvement flow split. In the futrue, adoption of CFD to design HVAC duct with modified $k-\varepsilon$ model will bring benefits of producing more accurate prediction, and also give designers more detail information much more than now.

• 한국유체기계학회 논문집
• /
• 제3권3호
• /
• pp.31-40
• /
• 2000

A computer program is developed for the prediction of the aerodynamic performance and the noise characteristics in the basic design step of axial flow fan. The flow field and the performance of fan are analyzed by using the streamline curvature computing scheme with total pressure loss and flow deviation models. Fan noise is assumed to be generated due to the pressure fluctuations induced by wake vortices of fan blades and to radiate via dipole distribution. The vortex-induced fluctuating pressure on blade surface is calculated by combining thin airfoil theory and the predicted flow field data. The predicted performances, sound pressure level and noise directivity patterns of fan by the present method are favorably compared with the test data of actual fan. Furthermore, the present method is shown to be very useful in optimizing design variables of fan with high efficiency and low noise level.

• 한국항공우주학회지
• /
• 제36권7호
• /
• pp.621-627
• /
• 2008

풍동에서 측정된 공력자료에는 풍동벽면의 영향으로 인하여 불가항력적인 오차가 포함되어 있다. 벽면영향이 없는 공력자료를 얻기 위해서는 이러한 원하지 않는 벽면효과를 제거 하여야 한다. 유선곡률 효과는 풍동벽면의 영향으로 유선의 곡률이 자유 흐름의 것과 다르기 때문에 발생한다. 고정익 항공기에 사용되고 있는 전통적인 유선곡률 효과를 보정방법인 Glauert의 보정방법은 회전익 항공기에 적용이 적절하지 않다. 본 논문에서는 로터에 적절한 후류모델을 사용하는 Heyson의 보정방법을 사용하여 로터축 기울어짐 각과 동압을 보정하였다. Heyson 보정방법의 결과를 Glauert 보정방법의 결과와 비교하였다.

• 대한기계학회논문집
• /
• 제12권4호
• /
• pp.865-875
• /
• 1988

본 연구에서는 부정숙 등에 의한 실험결과를 토대로 하여, 단이 진 2차원 벽 면분류에 대한 수치해석으로 표준 K-.epsilon.모델과 LRM 그리고 PAM을 적용하고, upwind 및 skew-upwind scheme을 적용하여 그 결과를 검토하고자 한다.