• Journal of the Korea institute for structural maintenance and inspection
• /
• v.4 no.4
• /
• pp.109-119
• /
• 2000

PVDF film sensor was applied to measure the stress concentration for monitoring the structural integrity. The strain calibration of this film sensor was performed by the bending test of aluminum beam. The PVDF sensor and the electrical strain gage were bonded on the beam. When the beam was loaded, the output of electrical strain gage was compared with the output of the PVDF sensor. The waveform of PVDF sensor output was shown as the same form of the output of electrical strain gage. The gain was determined as 1.7 by comparing these two signals to determine the exact value of the strain. In order to experiment the stress concentration, the stress field was analyzed by finite element analysis. The tensile test of notched steel specimens was conducted to develop the measurement technique of stress concentration. The output voltage ratio between the PVDF sensor near the notch and the PVDF sensor far from the notch could give the information about the load bearing capacity of steel specimen.

• Journal of the Korean Professional Engineers Association
• /
• v.19 no.4
• /
• pp.5-10
• /
• 1986

On SWS 41 Plates jointed by the F11T M 20 high strength bolts the study on stress behavior and safety degree until rupture in static tensile tests were performed. By these results, in case of no clamping force stress concentration was extremed for strain of about 10% higher ratio. Elastic strain occurred to change of test specimens depth by the load and plastic strain occurred to local minute sleep after elastic strain. compared shear stress with tension stress from the fracture load it was showned lower values than the maximum shear stress theory and stress strain energy theory.

• Journal of Korean Society of Environmental Engineers
• /
• v.36 no.10
• /
• pp.672-678
• /
• 2014

In this study, variations of fermentative hydrogen production and microbial community were investigated with different nitrogen concentration of food waste. Optimum hydrogen production rate was acquired at 200 mg/L nitrogen concentration of the food waste. Which was eqivalent to 83.43 mL/g dry biomass/hr. However, bio-hydrogen production was inhibitedly reduced at over 600 mg/L of nitrogen concentration whereas proportional relation between hydrogen production and B/A ratio were not observed. Most dominant specie of the microbial community analyzed was Clostridium sp. throughout PCR-DGGE analysis of 16S rDNA. It revealed that most contributing microorganism producing hydrogen were Enterococcus faecium partial, Klebsiella pneumoniae strain ND6, Enterobacter sp. NCCP-231, and Clostridium algidicarnis strain E107 in this experiment.

• Journal of the Korean Geotechnical Society
• /
• v.23 no.4
• /
• pp.169-183
• /
• 2007

Numerical analysis was performed to investigate the behavior of rammed aggregate piers (RAP) in soft ground with various interface conditions, area replacement ratio, aspect ratio and surcharge loads of pile and soil. And field modulus load test was carried out to predict the input parameters. Field prototype (unit cell) tests are in progress to compare the result of numerical analysis. Also a modified load transfer equation of RAP on soft foundation was proposed. According to the results, the behavior of RAP depended on such as interface conditions, settlement characteristics (free strain) and stress concentration ratio. On the other hand, maximun stress concentration ratio increased as area replacement ratio and aspect ratio increased, and it was remarkably affected by surcharge loads.

• Journal of Mechanical Science and Technology
• /
• v.18 no.5
• /
• pp.808-813
• /
• 2004

The stress analysis on orthotropic composite cylindrical shells with one circular or one elliptical cutout subjected to an axial force is carried out by using an analytical and experimental method. The composite cylindrical shell governing equation of the Donnell's type is applied to this study and all results are presented by the stress concentration factor. The stress concentration factor is defined as the ratio of the stress on the region around a cutout to the nominal stress of the shell. The stress concentration factor is classified into the circumferential stress concentration factors and the radial stress concentration factors due to the cylindrical coordinate of which the origin is the center of a cutout. The considered loading condition is only axial tension loading condition. In this study, thus, the maximum stress is induced on perpendicular region against axial direction, on the coordinate. Various cutout sizes are expressed using the radius ratio, (equation omitted), which is the radius of a cutout over one of the cylindrical shell. Experimental results are obtained using strain gages, which are attached around a cutout of the cylindrical shell. As the result from this study, the stress concentration around a cutout can be predicted by using the analytical method for an orthotropic composite cylindrical shell having a circular or an elliptical cutout.

• Journal of Ocean Engineering and Technology
• /
• v.4 no.1
• /
• pp.110-119
• /
• 1990

This study is concerned about the stress concentration factor measurement by photoelastic method, for the case of two circular holes arrangement in 3mm semi-infinite plate under tensile load, the ratio of those two circular holes diameter, the ratio of distance apart from circular holes to breadth and the two holes arrangement angle with loading direction were varied. Besides, the measured stress concentration by photoelastic method around one circular hole was compared with that by strain-gage method.

• Textile Coloration and Finishing
• /
• v.22 no.1
• /
• pp.51-60
• /
• 2010

This research works on the effects of drawing conditions on the physical properties of the drawn worsted yarns. The drawn worsted yarns were made by the yarn drawing system under various drawing conditions such as concentration of reducing agent, draw ratio, setting time of drawn yarn, and concentration of oxidizing agent. The drawn worsted yarns from 2/80Nm to 2/90Nm were obtained from 2/60Nm worsted yarns, the surface and cross-sectional shapes and tensile properties of these various specimens were measured and discussed with the various drawing conditions. The drawing of worsted yarn made constituent wool fiber scratched and made it changing to polygonal cross-sectional shape. The tenacity and modulus were increased with draw ratio and concentration of reducing agent. And tensile strain was increased with draw ratio, which decreased with concentration of reducing agent.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.30 no.4
• /
• pp.275-282
• /
• 2017

In this paper, using a pattern transformation triggered by deformation, we propose a porous structure that exhibits the characteristic of negative Poisson's ratio in both tension and compression. Due to the lack of torque for rotational motion of ligaments, the existing porous structure of circular holes shows positive Poisson's ratio under tension loading. Also, the porous structure of elliptic holes has a drawback of low durability due to stress concentration. Thus, we design curved ligaments to increase the rotational torque under tension and to alleviate the stress concentration such that strain energy is uniformly distributed in the whole structure. The developed structure possesses better stiffness and durability than the existing structures. It also exhibits the negative Poisson ratio in both compression and tension of 10% nominal strain. Through nonlinear finite element analysis, the performance of developed structure is compared with the existing structure of elliptic holes. The developed structure turns out to be significantly improved in terms of stiffness and durability.

• Proceedings of the KSME Conference
• /
• 2007.05a
• /
• pp.554-559
• /
• 2007

The cylinder cover stud for assembling the combustion chamber components of low-speed marine diesel engine is one of the main structural components in engine. To understand the structural behavior of the stud is quite important for safe and economic design of it. In this paper, the structural behavior and design adequacy of the stud have been evaluated through strain measurement and structural analysis for the world's two largest engine types. Moreover, a feasibility study for design modification was carried out based on fatigue test and calculation. The results showed that 1) the stud experiences very high stress ratio under normal operating conditions, 2) the fatigue strength of the stud is sufficient, and 3) results from strain measurement and structural analysis were quite close each other.

• Microbiology and Biotechnology Letters
• /
• v.19 no.4
• /
• pp.419-427
• /
• 1991

Ethanol fermentation of glucose by a strain of Saccharomyces cereuisiae was studied in membrane recycle bioreactor, where the fermentation vessel was coupled with cross flow hollow fiber membrane. The cell recycle system controlled backflushing with fresh medium was proven to be effective in alleviating membrane fouling and allowing long term operation of high-cell continuous fermentation. Using 100 g/l initial glucose concentration, the maximum productivity of about 9 5 g/$l \cdot h$ has been achieved at dilution rate 2.5 $h^{-1}$ and bleed stream ratio 0.05 with the corresponding ethanol concentration of 35g/l and glucose conversion of 100%. Increasing the glucose concentration to 200 g/$l \cdot h$ resulted in an increase in ethanol concentration to 48 g/l and productivity to 120 g1l.h. Substrate conversion, however, was only 69%. This productivity was the highest value in the study, and about 38 fold more than that of batch culture and 17 fold more that of single stage continuous culture without cell recycling. No further increase in the productivity was obtained when the glucose concentration was increased reased to 300g/l.