• 반도체디스플레이기술학회지
• /
• 제13권4호
• /
• pp.33-36
• /
• 2014

In this paper, a carbon strain gauge for large strain was developed. The carbon strain gauge was fabricated by forming PCB and antenna pattern using Cu/Ni/Au film and carbon resistor pattern using screen printing process on plastic film substrate. It was possible to develop low-cost disposable strain gauge since the carbon paste was cheap and the fabrication process was simple. The wireless communication type carbon strain gauge was fabricated by integrating signal processing circuit, antenna and power all together on the same substrate as a strain gauge. The wireless communication type carbon strain gauge has a merit of being available immediately at the spot without any particular system.

• 한국항행학회논문지
• /
• 제23권2호
• /
• pp.200-206
• /
• 2019

산업현장에서의 지게차의 전복에 의한 안전사고 빈도가 매우 높은 편이다. 지게차 전복의 가장 큰 원인은 과적으로, 이를 방지하기 위해서 적재 중량을 측정해야 한다. 가장 보편적인 적재 중량 측정 방식은 로드셀(load cell)로 측정 오차가 적은 장점이 있지만 설치 단가가 비싸다는 점 때문에 산업현장에 쉽게 적용하지 못하고 있다. 본 연구는 로드 셀 방식의 대안으로 제시되었지만 측량 정밀도가 높지 않은 strain gauge 센싱 방식을 적용한 지게차 새로운 적재 중량 측정 시스템을 제안한다. 센서의 측량 정밀도와 내구성을 높이기 위해 4개의 센서가 각각 4개의 anchor bolt에 삽입되는 구조로 제작하였다. 제작된 anchor 볼트 형태의 strain gauge 센서를 지게차에 적용하여 측정한 결과 1%의 측정 오차를 얻을 수 있었다.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1991년도 한국자동제어학술회의논문집(국내학술편); KOEX, Seoul; 22-24 Oct. 1991
• /
• pp.1198-1203
• /
• 1991

A single w& optical fiber strain gauge subjected to the excited PZT-plate is presented which was obtained using a Mach-Zehnder interferometer. This paper has been performed the considerations to the experimental situation In which the dynamical behavior of a optical fiber strain gauge is illustrated. A comparison is reported between the dynamic response of a optical fiber strain gauge and the semiconductor strain gauge in the frequency range 5-50Hz. This result is shown in very good usage as the dynamical measurement of the low strain below l.mu..epsilon. by this system.

• 산업기술연구
• /
• 제30권A호
• /
• pp.89-93
• /
• 2010

This research suggested a development of a Data Acquisition System for strain gauge sensor which enables the usage of portable device in the various engineering field that includes, a strain indicator which is frequently used in civil and mechanical engineering, and a GUI function of data acquisition device. The developed system can record 16 channels of strain gauges at a time and its resolution is over 16 bits which can be used effectively in the actual field.

• 대한전자공학회논문지
• /
• 제27권5호
• /
• pp.793-801
• /
• 1990

A single mode fiber-optic Mach-Zehnder interferometer for the measurement of strain is described. A fiber-optic strain gauge with great resolution and wide measurement range is realized. In order to varify the dynamic response, the measurements of strain below 1涅 with frequency range 5-50Hz are compared with a semiconductor strain gauge. We report theoretical evaluation for mechanical analysis, PZT-plate, the phase change in a fiber-optic strain gauge and a semiconductor strain gauge. The dynamical characteristics of a fiber-optic strain gauge and a semiconductor strain gauge output siganl show equivalent behavior. This result is shown in very good usage as the dynamical measurement of the low strain below 1涅 by this system.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2010년도 춘계학술대회 논문집
• /
• pp.1065-1066
• /
• 2010

• 한국소음진동공학회논문집
• /
• 제14권9호
• /
• pp.819-826
• /
• 2004

A multi-step optimum strategy for the selection of the locations and directions of strain gauges is proposed in this paper to capture at best the modal response of blade in a series of modes on fan blades. It is consist of three steps including two pass reduction step, genetic algorithm and fine optimization to find the locations-directions of strain gauges. The optimization is based upon the maximum signal-to-noise ratio(SNR) of measured strain values with respect to the inherent system measurement noise, the mispositioning of the gauge in location and gauge failure. Optimal gauge positions for a fan blade is analyzed to prove the effectiveness of the multi-step optimum methodology and to investigate the effects of the considering parameters such as the mispositioning level, the probability of gauge failure, and the number of gauges on the optimal strain gauge position.

• 제어로봇시스템학회논문지
• /
• 제12권9호
• /
• pp.912-917
• /
• 2006

A strain gauge weight measuring instrumentation system was designed with RF sensor network facilities. In the sensor module system data conversion and a series of signal processing were totally equipped. 16 strain gauges are incoming sensors and each output of the strain gauge was amplified and filtered for proper analog signal processing. Several measuring instrumentation OP amps and general purposed OP amps were used. 12 bits A/D converters converted analog signals to digital bits and a PIC microprocessor controlled the 16 channels of strain gauges. RF RS232 modules were used for wireless communication between the PIC microprocessor and an Ethernet host far a remote sensor monitoring system development.

• 센서학회지
• /
• 제21권1호
• /
• pp.75-81
• /
• 2012

Optimizing the tapping time of a blast furnace is important to a stable operation and life extension. To optimize the tapping time of the blast furnace, the location of Hearth Liquid Level should be recognized. There are several ways to measure the hearth liquid level in the blast furnace, such as Electromotive Force(EMF) measurement, pressure measurement by putting in nitrogen probe and manometry with strain gauge. In this paper, it will be discussed using strain gauge among the three methods. Conventional strain gauge must be revised periodically. Since, internal pressure, temperature of internal refractory material and wind pressure have effect on the strain gauge. However, static pressure value is required to compensate. To solve these problems, this paper suggests finding relationship between Hearth Liquid Level and strain gauge output, adding digital filter in strain gauge. Using the proposed method, it was possible to estimate the hearth liquid level and determine the appropriate tapping time. Usefulness of the proposed method through simulations and experimental results are confirmed.

• 대한기계학회논문집A
• /
• 제30권5호
• /
• pp.560-567
• /
• 2006

The exact load measurements for the mechanical parts of a wind turbine are important step both fur the evaluation of a specific wind turbine design and for a certification process. A common method for a mechanical load measurement is using a strain gauge sensing. Two main problems ought to be answered in order for this method to be applied to the wind turbine project. These are strain gauge calibration and non-contact signal transmission from the strain gauge output to a load monitoring system. This paper suggests reliable solutions fer these two problems. A Bluetooth, a short range wireless data communication technology, is used to solve the second problem. The first one, the strain gauge calibration methodology for a load measurement in a wind turbine application, is fully explained in this paper. Various mechanical loadings for a strain gauge calibration in a wind turbine load measurement are introduced and analyzed. Initial experimental results which are obtained from a 1 kW small size wind turbine are analyzed, and the uncertainty problem in estimating mechanical loads using a calibration matrix is fully covered in this paper.